V-band CMOS injection-locked frequency tripler using differential harmonic current injection technique

2021 ◽  
Author(s):  
Yu-Hsin Chang
Keyword(s):  
Current Injection ◽  
Injection Technique ◽  
Harmonic Current ◽  
V Band

scholarly journals Fast control of the six phase asymmetric generator with the 3rd harmonic current injection

2016 ◽  
Vol 65 (1) ◽  
pp. 59-71
Author(s):  
Marek Gołębiowski
Keyword(s):  
Wind Turbine ◽  
Current Injection ◽  
Injection Technique ◽  
Harmonic Current ◽  
Flux Control ◽  
Constant Flux ◽  
Constant Torque ◽  
Wind Turbine System ◽  
Fast Control ◽  
Generator Performance

Abstract In this paper the MTPA, MTPF, constant torque and constant flux control trajectories are presented. These trajectories are calculated for a 6-phase asymmetric insettype SMPMSM generator with the assumption of a certain level of 3rd harmonic current injection. This injection technique increases the generator performance due to the cooperation of the fundamental and 3rd harmonic. The presented trajectories are used for fast control of the generator working in the gearless wind turbine system.

scholarly journals A Novel Method for Harmonic Current Injection with Sensor Supported Adaptation on Permanent Magnet Synchronous Machines

Machines ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 139
Author(s):  
Matthias Vollat ◽  
Dominik Krahe ◽  
Frank Gauterin
Keyword(s):  
Permanent Magnet ◽  
Current Injection ◽  
Synchronous Machines ◽  
Permanent Magnet Synchronous Machine ◽  
Permanent Magnet Synchronous Machines ◽  
Harmonic Current ◽  
Harmonic Currents ◽  
Sensor Signals ◽  
Novel Method ◽  
Higher Harmonic

To reduce torque oscillations in electric motors, harmonic current injection (HCI) has been used in industry for some time. For this purpose, higher harmonic currents calculated in advance are injected into the machine. Since the general conditions for the machine can change during its life cycle, this article presents a method that makes it possible to change the parameters of HCI during operation. For this purpose, sensor signals are used to detect the reaction of the electric motor to small variations of the HCI parameters. The knowledge gained in this way is used to make further suitable variations. FEM simulations were used to verify the effectiveness of the approach. The results show that the algorithm can independently optimize the HCI parameters during runtime and reduces the amplitude of the 6th harmonic in the torque by 87% for a permanent magnet synchronous machine.

scholarly journals High-Harmonic Injection-Based Brushless Wound Field Synchronous Machine Topology

Mathematics ◽  
2021 ◽  
Vol 9 (15) ◽  
pp. 1721
Author(s):  
Syed Sabir Hussain Bukhari ◽  
Fareed Hussain Mangi ◽  
Irfan Sami ◽  
Qasim Ali ◽  
Jong-Suk Ro
Keyword(s):  
High Harmonic ◽  
Current Injection ◽  
Harmonic Current ◽  
Element Analysis ◽  
Magnetomotive Force ◽  
Excitation Scheme ◽  
Three Phase ◽  
Harmonic Injection ◽  
Field Excitation ◽  
Electromagnetic Performance

This paper discusses the design and analysis of a high-harmonic injection-based field excitation scheme for the brushless operation of wound field synchronous machines (WFSMs) in order to achieve a higher efficiency. The proposed scheme involves two inverters. One of these inverters provides the three-phase fundamental-harmonic current to the armature winding, whereas the second inverter injects the single-phase high-harmonic i.e., 6th harmonic current in this case, to the neutral-point of the Y-connected armature winding. The injection of the high-harmonic current in the armature winding develops the high-harmonic magnetomotive force (MMF) in the air gap of the machine beside the fundamental. The high-harmonic MMF induces the harmonic current in the excitation winding of the rotor, whereas the fundamental MMF develops the main armature field. The harmonic current is rectified to inject the direct current (DC) into the main rotor field winding. The main armature and rotor fields, when interacting with each other, produce torque. Finite element analysis (FEA) is carried out in order to develop a 4-pole 24-slot machine and investigate it using a 6th harmonic current injection for the rotor field excitation to both attain a brushless operation and analyze its electromagnetic performance. Later on, the performance of the proposed topology is compared with the typical brushless WFSM topology employing the 3rd harmonic current injection-based field excitation scheme.

scholarly journals Third harmonic current injection into highly saturated multi-phase machines

2017 ◽  
Vol 66 (1) ◽  
pp. 179-187
Author(s):  
Felix Klute ◽  
Torben Jonsky
Keyword(s):  
Current Injection ◽  
Saturation Level ◽  
Permanent Magnet Synchronous Machines ◽  
Flux Linkage ◽  
Harmonic Current ◽  
Fem Model ◽  
Third Harmonic ◽  
The Third ◽  
Rotor Flux ◽  
Multi Phase

Abstract One advantage of multi-phase machines is the possibility to use the third harmonic of the rotor flux for additional torque generation. This effect can be maximised for Permanent Magnet Synchronous Machines (PMSM) with a high third harmonic content in the magnet flux. This paper discusses the effects of third harmonic current injection (THCI) on a five-phase PMSM with a conventional magnet shape depending on saturation. The effects of THCI in five-phase machines are shown in a 2D FEM model in Ansys Maxwell verified by measurement results. The results of the FEM model are analytically analysed using the Park model. It is shown in simulation and measurement that the torque improvement by THCI increases significantly with the saturation level, as the amplitude of the third harmonic flux linkage increases with the saturation level but the phase shift of the rotor flux linkage has to be considered. This paper gives a detailed analysis of saturation mechanisms of PMSM, which can be used for optimizing the efficiency in operating points of high saturations, without using special magnet shapes.

Sign in / Sign up

Export Citation Format

Share Document