Microstructure, mechanical properties and in vitro biocompatibilities of a novel bionic hydroxyapatite bone scaffold prepared by the addition of boron nitride

2020 ◽  
Vol 55 (29) ◽  
pp. 14501-14515 ◽  
Author(s):  
Changbo Wang ◽  
Jinyang Feng ◽  
Jian Zhou ◽  
Xiaoguang Huang ◽  
Lin Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Bone Scaffold

scholarly journals Sustainable Boron Nitride Nanosheet-Reinforced Cellulose Nanofiber Composite Film with Improved Mechanical Properties and Oxygen Barrier without the Cost of Color and Brittleness

2018 ◽  
Author(s):  
Hoang-Linh Nguyen ◽  
Zahid Hanif ◽  
Seul-A. Park ◽  
Bong Gill Choi ◽  
Thang Hong Tran ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Boron Nitride ◽  
Composite Film ◽  
Food Packaging ◽  
Color Change ◽  
Cellulose Nanofiber ◽  
Oxygen Barrier ◽  
Boron Nitride Nanosheet

Herein, we introduce a boron nitride nanosheet (BNNS)-reinforced cellulose nanofiber (CNF) film as a sustainable oxygen barrier film that can potentially be applied in food packaging. Most of commodity plastics are oxygen-permeable. CNF exhibits an ideal oxygen transmittance rate (OTR) of <1 cc/m2/day in highly controlled conditions. A CNF film typically fabricated by the air drying of a CNF aqueous solution reveals an OTR of 19.08 cc/m2/day. The addition of 0-5 wt% BNNS to the CNF dispersion before drying results in a composite film with highly improved OTR, 4.7 cc/m2/day, which is sufficient for meat and cheese packaging. BNNS as a 2D nanomaterial increases the pathway of oxygen gas and reduces the chances of pin-hole formation during film fabrication involving water drying. In addition, BNNS improves the mechanical properties of the CNF films (Young’s modulus and tensile strength) without significant elongation reductions, probably due to the good miscibility of CNF and BNNS in the aqueous solution. BNNS addition also produces negligible color change, which is important for film aesthetics. An in vitro cell experiment was performed to reveal the low cytotoxicity of the CNF/BNNS composite. This composite film has great potential as a sustainable high-performance food packaging material.

Boron nitride nanotube reinforced polylactide–polycaprolactone copolymer composite: Mechanical properties and cytocompatibility with osteoblasts and macrophages in vitro

2010 ◽  
Vol 6 (9) ◽  
pp. 3524-3533 ◽  
Author(s):  
Debrupa Lahiri ◽  
Francois Rouzaud ◽  
Tanisha Richard ◽  
Anup K. Keshri ◽  
Srinivasa R. Bakshi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Boron Nitride Nanotube

Cytocompatibility and Material Properties of Poly-carbonate Urethane/Carbon Nanofiber Composites for Neural Applications

2003 ◽  
Vol 774 ◽  
Author(s):  
Janice L. McKenzie ◽  
Michael C. Waid ◽  
Riyi Shi ◽  
Thomas J. Webster
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanofibers ◽  
Material Properties ◽  
Carbon Nanofiber ◽  
Scar Tissue ◽  
Tissue Response ◽  
Positive Interactions ◽  
Weight Percentage ◽  
Poly Carbonate

AbstractCarbon nanofibers possess excellent conductivity properties, which may be beneficial in the design of more effective neural prostheses, however, limited evidence on their cytocompatibility properties exists. The objective of the present in vitro study was to determine cytocompatibility and material properties of formulations containing carbon nanofibers to predict the gliotic scar tissue response. Poly-carbonate urethane was combined with carbon nanofibers in varying weight percentages to provide a supportive matrix with beneficial bulk electrical and mechanical properties. The substrates were tested for mechanical properties and conductivity. Astrocytes (glial scar tissue-forming cells) were seeded onto the substrates for adhesion. Results provided the first evidence that astrocytes preferentially adhered to the composite material that contained the lowest weight percentage of carbon nanofibers. Positive interactions with neurons, and, at the same time, limited astrocyte functions leading to decreased gliotic scar tissue formation are essential for increased neuronal implant efficacy.

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

Boron nitride for modification of rubber based on isoprene elastomer

2020 ◽  
pp. 105-112
Author(s):  
K. S. Zhansakova ◽  
E. N. Eremin ◽  
G. S. Russkikh ◽  
O. V. Kropotin
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Gradual Increase ◽  
Physical And Mechanical Properties ◽  
Curing Time ◽  
Cross Link ◽  
Start Time ◽  
Link Density ◽  
Cross Link Density ◽  
Isoprene Rubber

The work studies vulcanization characteristics of elastomers based on isoprene rubber filled with carbon black N330 and boron nitride (BN). The influence of the boron nitride (BN) concentration on technological, dynamic, physical and mechanical properties of elastomers has been researched. The application of boron nitride for producing rubber with good properties has been considered. With a gradual increase of the inert filler BN concentration up to 35%, a decrease in the curing rate by 33% and polymer cross-link density by 26% is observed. Moreover, the start time of vulcanization increases by almost 300%, the optimal curing time by 200%.

scholarly journals Anti-Inflammatory Properties of Injectable Betamethasone-Loaded Tyramine-Modified Gellan Gum/Silk Fibroin Hydrogels

Biomolecules ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1456
Author(s):  
Isabel Matos Oliveira ◽  
Cristiana Gonçalves ◽  
Myeong Eun Shin ◽  
Sumi Lee ◽  
Rui Luis Reis ◽  
...  
Keyword(s):  
Rheumatoid Arthritis ◽  
Mechanical Properties ◽  
Silk Fibroin ◽  
Therapeutic Efficacy ◽  
Composite Structures ◽  
Gelation Time ◽  
Polymeric Materials ◽  
Gellan Gum ◽  
Traditional Use

Rheumatoid arthritis is a rheumatic disease for which a healing treatment does not presently exist. Silk fibroin has been extensively studied for use in drug delivery systems due to its uniqueness, versatility and strong clinical track record in medicine. However, in general, natural polymeric materials are not mechanically stable enough, and have high rates of biodegradation. Thus, synthetic materials such as gellan gum can be used to produce composite structures with biological signals to promote tissue-specific interactions while providing the desired mechanical properties. In this work, we aimed to produce hydrogels of tyramine-modified gellan gum with silk fibroin (Ty–GG/SF) via horseradish peroxidase (HRP), with encapsulated betamethasone, to improve the biocompatibility and mechanical properties, and further increase therapeutic efficacy to treat rheumatoid arthritis (RA). The Ty–GG/SF hydrogels presented a β-sheet secondary structure, with gelation time around 2–5 min, good resistance to enzymatic degradation, a suitable injectability profile, viscoelastic capacity with a significant solid component and a betamethasone-controlled release profile over time. In vitro studies showed that Ty–GG/SF hydrogels did not produce a deleterious effect on cellular metabolic activity, morphology or proliferation. Furthermore, Ty–GG/SF hydrogels with encapsulated betamethasone revealed greater therapeutic efficacy than the drug applied alone. Therefore, this strategy can provide an improvement in therapeutic efficacy when compared to the traditional use of drugs for the treatment of rheumatoid arthritis.

scholarly journals Mechanical Properties, Corrosion Resistance and Bioactivity of Oxide Layers Formed by Isothermal Oxidation of Ti-6Al-7Nb Alloy

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 505
Author(s):  
Krzysztof Aniołek ◽  
Bożena Łosiewicz ◽  
Julian Kubisztal ◽  
Patrycja Osak ◽  
Agnieszka Stróż ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Contact Potential Difference ◽  
Isothermal Oxidation ◽  
Potential Method ◽  
Open Circuit ◽  
Kelvin Probe ◽  
Contact Potential ◽  
Oxide Layers

Titanium and its alloys are among the most promising biomaterials for medical applications. In this work, the isothermal oxidation of Ti-6Al-7Nb biomedical alloy towards improving its mechanical properties, corrosion resistance, and bioactivity has been developed. The oxide layers were formed at 600, 700, and 800 °C for 72 h. Scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), 3D profilometry, and microindentation test, were used to characterize microstructure, surface geometrical structure, and the hardness of the diphase (α + β) Ti-6Al-7Nb alloy after oxidation, respectively. In vitro corrosion resistance tests were carried out in a saline solution at 37 °C using the open-circuit potential method and potentiodynamic measurements. Electronic properties in the air were studied using the Scanning Kelvin Probe (SKP) technique. The bioactivity test was conducted by soaking the alkali- and heat-treated samples in simulated body fluid for 7 days. The presence of apatite was confirmed using SEM/EDS and Fourier Transform Infrared Spectroscopy (FTIR) studies. The thickness of oxide layers formed increased with the temperature growth from 0.25 to 5.48 µm. It was found that with increasing isothermal oxidation temperature, the surface roughness, hardness, corrosion resistance, and contact potential difference increased. The Ti-6Al-7Nb alloy after oxidation revealed the HAp-forming ability in a biological environment.

Sign in / Sign up

Export Citation Format

Share Document