Transcript abundance of enzymes involved in lignin biosynthesis of Eucalyptus globulus genotypes with contrasting levels of pulp yield and wood density

2011 ◽  
Vol 7 (4) ◽  
pp. 697-705 ◽  
Author(s):  
Juan Pedro Elissetche ◽  
Sofía Valenzuela ◽  
Renán García ◽  
Marcela Norambuena ◽  
Carolina Iturra ◽  
...  
Keyword(s):  
Wood Density ◽  
Eucalyptus Globulus ◽  
Lignin Biosynthesis ◽  
Transcript Abundance ◽  
Pulp Yield

Direct Effects of Wood Characteristics on Pulp and Handsheet Properties of Eucalyptus globulus

Holzforschung ◽  
2002 ◽  
Vol 56 (3) ◽  
pp. 244-252 ◽  
Author(s):  
R. Wimmer ◽  
G.M. Downes ◽  
R. Evans ◽  
G. Rasmussen ◽  
J. French
Keyword(s):  
Wood Density ◽  
Eucalyptus Globulus ◽  
Strong Predictor ◽  
Fibre Length ◽  
Microfibril Angle ◽  
Wood Properties ◽  
Bending Stiffness ◽  
Pulp Yield ◽  
Paper Properties ◽  
Handsheet Properties

Summary Fibre length, microfibril angle and wood density were measured in eight-year-old Eucalyptus globulus clones planted on three different sites. Samples were chipped and pulped, and the pulps beaten prior to preparation of 60g/m2 handsheets. Eleven physical handsheet properties, together with pulp freeness, were measured using standard methods. Direct relationships between wood properties and pulp/paper properties were studied using path analysis. Fibre length had a strong, direct effect on tear index, bending stiffness, freeness, pulp yield and active alkali consumption. Wood density was a strong predictor of most handsheet properties: high density woods produced bulkier, more porous sheets with higher bending stiffness, while lower density woods produced smoother, denser sheets with higher tensile strength.The effect of microfibril angle was small and more evident in handsheets made from beaten pulp.

scholarly journals Genetic parameters for growth, wood density and pulp yield in Eucalyptus globulus

2008 ◽  
Vol 5 (2) ◽  
pp. 291-305 ◽  
Author(s):  
João Costa e Silva ◽  
Nuno M. G. Borralho ◽  
José A. Araújo ◽  
René E. Vaillancourt ◽  
Brad M. Potts
Keyword(s):  
Wood Density ◽  
Eucalyptus Globulus ◽  
Genetic Parameters ◽  
Pulp Yield

Genetic control of kraft pulp yield in Eucalyptus globulus

2010 ◽  
Vol 40 (5) ◽  
pp. 917-927 ◽  
Author(s):  
Desmond J. Stackpole ◽  
René E. Vaillancourt ◽  
Geoffrey M. Downes ◽  
Christopher E. Harwood ◽  
Brad M. Potts
Keyword(s):  
Genetic Control ◽  
Eucalyptus Globulus ◽  
Kraft Pulp ◽  
Near Infrared ◽  
Genetic Correlations ◽  
Basic Density ◽  
Pulp Yield ◽  
Narrow Sense Heritability ◽  
Selection Gradients ◽  
Economic Worth

Pulp yield is an important breeding objective for Eucalyptus globulus Labill., but evaluation of its genetic control and genetic correlations with other traits has been limited by its high assessment cost. We used near infrared spectroscopy to study genetic variation in pulp yield and other traits in a 16-year-old E. globulus trial. Pulp yield was predicted for 2165 trees from 467 open-pollinated families from 17 geographic subraces. Significant differences between subraces and between families within subraces were detected for all traits. The high pulp yield of southern Tasmanian subraces suggested that their economic worth was previously underestimated. The narrow-sense heritability of pulp yield was medium (0.40). The significant positive genetic correlation between pulp yield and diameter (0.52) was at odds with the generally neutral values reported. The average of the reported genetic correlations between pulp yield and basic density (0.50) was also at odds with our nonsignificant estimate. Pulp yield of the subraces increased with increasing latitude, producing a negative correlation with density (–0.58). The absence of genetic correlations within subraces between pulp yield and density suggests that the correlation may be an independent response of the two traits to the same or different selection gradients that vary with latitude.

scholarly journals Chemical characteristics and Kraft pulping of tension wood from Eucalyptus globulus labill

2012 ◽  
Vol 36 (6) ◽  
pp. 1163-1172 ◽  
Author(s):  
María Graciela Aguayo ◽  
Regis Teixeira Mendonça ◽  
Paulina Martínez ◽  
Jaime Rodríguez ◽  
Miguel Pereira
Keyword(s):  
Eucalyptus Globulus ◽  
Lignin Content ◽  
Strength Properties ◽  
Kraft Pulping ◽  
Pulp Yield ◽  
Chemical Characteristics ◽  
Kraft Pulps ◽  
Opposite Wood ◽  
Alkali Consumption ◽  
Pulp Strength

Tension (TW) and opposite wood (OW) of Eucalyptus globulus trees were analyzed for its chemical characteristics and Kraft pulp production. Lignin content was 16% lower and contained 32% more syringyl units in TW than in OW. The increase in syringyl units favoured the formation of β-O-4 bonds that was also higher in TW than in OW (84% vs. 64%, respectively). The effect of these wood features was evaluated in the production of Kraft pulps from both types of wood. At kappa number 16, Kraft pulps obtained from TW demanded less active alkali in delignification and presented slightly higher or similar pulp yield than pulps made with OW. Fiber length, coarseness and intrinsic viscosity were also higher in tension than in opposite pulps. When pulps where refined to 30°SR, TW pulps needed 18% more revolutions in the PFI mill to achieve the same beating degree than OW pulps. Strength properties (tensile, tear and burst indexes) were slightly higher or similar in tension as compared with opposite wood pulps. After an OD0(EO)D1 bleaching sequence, both pulps achieved up to 89% ISO brightness. Bleached pulps from TW presented higher viscosity and low amount of hexenuronic acids than pulps from OW. Results showed that TW presented high xylans and low lignin content that caused a decrease in alkali consumption, increase pulp strength properties and similar bleaching performance as compared with pulps from OW.

Effect of fertilizer on wood properties of Eucalyptus globulus

2000 ◽  
Vol 30 (1) ◽  
pp. 136-144 ◽  
Author(s):  
C A Raymond ◽  
A Muneri
Keyword(s):  
Eucalyptus Globulus ◽  
Fibre Length ◽  
Basic Density ◽  
Wood Properties ◽  
Pulp Yield ◽  
Growth Responses ◽  
P Concentration ◽  
Tree Growth Rate ◽  
Western Australian ◽  
P Fertilizers

The effects of N and P fertilizers applied to Eucalyptus globulus Labill. at plantation establishment on basic density, fibre length, fibre coarseness, predicted pulp yield, and N and P concentration in the wood were examined by sampling four fertilizer factorial trials: three in Victoria and one in Western Australia. Treatments sampled were control, maximum levels of N and P by themselves and combined. Growth responses varied across sites with significant growth responses at the Victorian sites but no response at the Western Australian site. An interaction was suggested between rainfall and the effects of the fertilizer; wood properties at the drier sites were detrimentally affected by fertilizer but there was little effect at the wetter sites. On the two drier sites, application of both N and P, alone or in combination, resulted in changes in density, shorter fibres, and slightly lower predicted pulp yield. Addition of both N and P increased the levels of these nutrients in the wood at the three Victorian sites. Changes occurred in wood properties in the absence of growth responses to the applied fertilizer indicating that these changes were not induced by changing tree growth rate.

Relationships between Density, Shrinkage, Extractives Content and Microfibril Angle in Tension Wood from Three Provenances of 10-Year-Old Eucalyptus globulus Labill

Holzforschung ◽  
2001 ◽  
Vol 55 (2) ◽  
pp. 176-182 ◽  
Author(s):  
R. Washusen ◽  
P. Ades ◽  
R. Evans ◽  
J. Ilic ◽  
P. Vinden
Keyword(s):  
Wood Density ◽  
Eucalyptus Globulus ◽  
Tension Wood ◽  
Microfibril Angle ◽  
Positive Association ◽  
Normal Wood ◽  
X Ray Diffraction ◽  
X Ray ◽  
Saturation Method ◽  
Improvement Programs

Summary Density and microfibril angle (MFA) of tension wood and normal wood were assessed in the sapwood and heartwood, from three provenanaces of 10-year-old Eucalyptus globulus Labill. Density was measured using a modified saturation method that also enabled the calculation of the extractives lost during saturation. Microdensity and MFA were determined by SilviScan 2, a rapid X-ray densitometry and X-ray diffraction system developed at CSIRO. Significant differences were found in density and extractives between provenances and also density between the sapwood and adjacent heartwood from each provenance. This result may explain some of the drying differences between provenances found in an earlier study (Washusen and Ilic 2000). Sapwood samples with high percentages of tension wood fibres had high density and a significant positive correlation was found between microdensity and tension wood fibre percentage. MFA was found to be very low in normal wood in the sapwood, where most tension wood was found, so tension wood could not be identified by MFA. The positive association between tension wood and wood density suggests that caution should be taken when selecting trees for high wood density in tree improvement programs.

scholarly journals Towards a Systems Approach for Lignin Biosynthesis in Populus trichocarpa: Transcript Abundance and Specificity of the Monolignol Biosynthetic Genes

2009 ◽  
Vol 51 (1) ◽  
pp. 144-163 ◽  
Author(s):  
Rui Shi ◽  
Ying-Hsuan Sun ◽  
Quanzi Li ◽  
Steffen Heber ◽  
Ronald Sederoff ◽  
...  
Keyword(s):  
Systems Approach ◽  
Populus Trichocarpa ◽  
Lignin Biosynthesis ◽  
Transcript Abundance ◽  
Biosynthetic Genes

Development of near infrared reflectance analysis calibrations for estimating genetic parameters for cellulose content in Eucalyptus globulus

2002 ◽  
Vol 32 (1) ◽  
pp. 170-176 ◽  
Author(s):  
C A Raymond ◽  
L R Schimleck
Keyword(s):  
Eucalyptus Globulus ◽  
Kraft Pulp ◽  
Near Infrared ◽  
Genetic Correlations ◽  
Basic Density ◽  
Pulp Yield ◽  
Cellulose Content ◽  
Infrared Reflectance ◽  
Near Infrared Reflectance ◽  
Reflectance Analysis

Determining kraft pulp yield in the traditional way is slow and expensive, limiting the numbers of samples that may be processed. An alternative is to use a secondary standard, such as cellulose content of the wood, which is strongly correlated with kraft pulp yield. The feasibility and efficiency of predicting cellulose content using near infrared reflectance (NIR) analysis was examined for Eucalyptus globulus Labill. Calibrations for NIR prediction of cellulose content indicated that NIR analysis could be used as a reliable predictor. Standard errors of calibration were 1% or lower, and there was excellent agreement between laboratory and predicted cellulose values. Cellulose content was under moderate genetic control (h2 ranging from 0.32 to 0.57), and genetic correlations with tree diameter and basic density were variable (ranging from –0.11 to –0.51 and –0.33 to 0.67, respectively). The advantages, disadvantages, and potential applications of NIR analysis for predicting cellulose content are examined.

Calibration and Uncertainty Analysis of a Carbon Accounting Model to Stem Wood Density and Partitioning of Biomass for Eucalyptus globulus and Pinus Radiata

New Forests ◽  
2006 ◽  
Vol 31 (3) ◽  
pp. 513-533 ◽  
Author(s):  
Keryn Paul ◽  
Phil Polglase ◽  
Peter Snowdon ◽  
Tivi Theiveyanathan ◽  
John Raison ◽  
...  
Keyword(s):  
Uncertainty Analysis ◽  
Wood Density ◽  
Pinus Radiata ◽  
Eucalyptus Globulus ◽  
Carbon Accounting ◽  
Stem Wood ◽  
Accounting Model
Sign in / Sign up

Export Citation Format

Share Document