An investigation on the performance of lightweight mortar-based geopolymer containing high-volume LECA aggregate against high temperatures

AbstractA hot workability study was conducted on an orthorhombic Ti-21AI-23Nb alloy using isothermal, constant velocity compression tests, over the temperature range 900–1155°C and nominal strain rate range 0.001 to 1.0 s−1. Three different microstructures corresponding to (a) hot rolled and mill annealed, (b) β0 -heat treated, and (c) β0 solution treated and direct aged conditions were examined. These microstructures varied from a relatively coarse distribution of O-phase precipitates in a matrix of transformed βO to the metastable retained βO. Flow stress displayed a sharp dependence on temperature, strain rate and on the initial structure. While uniform plastic flow was obtained at high temperatures and for structures containing primary O, βO-heat treated structures led to pronounced flow softening. Strong yield point phenomena and serrated flow were observed in selected test conditions and for microstructures containing high volume fractions of metastable βO. These flow instabilities resulting from Luder band propagation and dynamic strain aging are interpreted in terms of dislocation interactions in supersaturated βO.

Download Full-text

Morphology, Distribution and Identification of Micro-Constituents Along Grain Boundaries in Nickel-Base Alloys

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100071326 ◽

1973 ◽

Vol 31 ◽

pp. 176-177

Author(s):

D. E. Fornwalt ◽

A. R. Geary ◽

B. H. Kear

Keyword(s):

Electron Microscope ◽

Grain Boundaries ◽

Volume Fraction ◽

Rupture Life ◽

Stress Rupture ◽

High Volume ◽

Precipitate Morphology ◽

Stress Rupture Life ◽

Nickel Base ◽

Scanning Electron

A systematic study has been made of the effects of various heat treatments on the microstructures of several experimental high volume fraction γ’ precipitation hardened nickel-base alloys, after doping with ∼2 w/o Hf so as to improve the stress rupture life and ductility. The most significant microstructural chan§e brought about by prolonged aging at temperatures in the range 1600°-1900°F was the decoration of grain boundaries with precipitate particles.Precipitation along the grain boundaries was first detected by optical microscopy, but it was necessary to use the scanning electron microscope to reveal the details of the precipitate morphology. Figure 1(a) shows the grain boundary precipitates in relief, after partial dissolution of the surrounding γ + γ’ matrix.

Download Full-text

In situ REM imaging of surface processes on ceramic bulk crystals from 300 to 1670 K in a conventional TEM

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100087616 ◽

1991 ◽

Vol 49 ◽

pp. 660-661

Author(s):

Z. L. Wang ◽

J. Bentley

Keyword(s):

High Temperatures ◽

Image Resolution ◽

Atomic Processes ◽

Crystal Surfaces ◽

Beam Radiation ◽

Surface Areas ◽

Transmission Electron ◽

Reflection Electron Microscopy ◽

Gas Reactions

Studying the behavior of surfaces at high temperatures is of great importance for understanding the properties of ceramics and associated surface-gas reactions. Atomic processes occurring on bulk crystal surfaces at high temperatures can be recorded by reflection electron microscopy (REM) in a conventional transmission electron microscope (TEM) with relatively high resolution, because REM is especially sensitive to atomic-height steps.Improved REM image resolution with a FEG: Cleaved surfaces of a-alumina (012) exhibit atomic flatness with steps of height about 5 Å, determined by reference to a screw (or near screw) dislocation with a presumed Burgers vector of b = (1/3)<012> (see Fig. 1). Steps of heights less than about 0.8 Å can be clearly resolved only with a field emission gun (FEG) (Fig. 2). The small steps are formed by the surface oscillating between the closely packed O and Al stacking layers. The bands of dark contrast (Fig. 2b) are the result of beam radiation damage to surface areas initially terminated with O ions.

Download Full-text

A Comparison of Tem and Apfim to the Interpretation of Modulated Microstructures

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s042482010011742x ◽

1985 ◽

Vol 43 ◽

pp. 70-71

Author(s):

M.G. Burke ◽

M.K. Miller

Keyword(s):

Low Temperature ◽

Microstructural Characterization ◽

Superlattice Reflection ◽

High Volume ◽

Atom Probe ◽

Dark Field ◽

Miscibility Gap ◽

Second Phase ◽

Two Phase ◽

Probe Field

Interpretation of fine-scale microstructures containing high volume fractions of second phase is complex. In particular, microstructures developed through decomposition within low temperature miscibility gaps may be extremely fine. This paper compares the morphological interpretations of such complex microstructures by the high-resolution techniques of TEM and atom probe field-ion microscopy (APFIM).The Fe-25 at% Be alloy selected for this study was aged within the low temperature miscibility gap to form a <100> aligned two-phase microstructure. This triaxially modulated microstructure is composed of an Fe-rich ferrite phase and a B2-ordered Be-enriched phase. The microstructural characterization through conventional bright-field TEM is inadequate because of the many contributions to image contrast. The ordering reaction which accompanies spinodal decomposition in this alloy permits simplification of the image by the use of the centered dark field technique to image just one phase. A CDF image formed with a B2 superlattice reflection is shown in fig. 1. In this CDF micrograph, the the B2-ordered Be-enriched phase appears as bright regions in the darkly-imaging ferrite. By examining the specimen in a [001] orientation, the <100> nature of the modulations is evident.

Download Full-text