Deformation Behavior of An O + β0 Processed Ti-21 Ai-23Nb Alloy at High Temperatures

1994 ◽  
Vol 364 ◽  
Author(s):  
Venkat Seetharaman
Keyword(s):  
Strain Rate ◽  
High Temperatures ◽  
High Volume ◽  
Strain Rate Range ◽  
Dynamic Strain ◽  
Initial Structure ◽  
Hot Workability ◽  
Compression Tests ◽  
Nominal Strain Rate ◽  
Heat Treated

AbstractA hot workability study was conducted on an orthorhombic Ti-21AI-23Nb alloy using isothermal, constant velocity compression tests, over the temperature range 900–1155°C and nominal strain rate range 0.001 to 1.0 s−1. Three different microstructures corresponding to (a) hot rolled and mill annealed, (b) β0 -heat treated, and (c) β0 solution treated and direct aged conditions were examined. These microstructures varied from a relatively coarse distribution of O-phase precipitates in a matrix of transformed βO to the metastable retained βO. Flow stress displayed a sharp dependence on temperature, strain rate and on the initial structure. While uniform plastic flow was obtained at high temperatures and for structures containing primary O, βO-heat treated structures led to pronounced flow softening. Strong yield point phenomena and serrated flow were observed in selected test conditions and for microstructures containing high volume fractions of metastable βO. These flow instabilities resulting from Luder band propagation and dynamic strain aging are interpreted in terms of dislocation interactions in supersaturated βO.

Hot Workability of a High Strength Low Alloy Steel for Construction Application

2012 ◽  
Vol 724 ◽  
pp. 178-181
Author(s):  
Woo Young Jung ◽  
Tae Kwon Ha
Keyword(s):  
Strain Rate ◽  
Power Dissipation ◽  
High Efficiency ◽  
Hsla Steel ◽  
High Strength ◽  
Plastic Instability ◽  
Strain Rate Range ◽  
Hot Workability ◽  
Compression Tests ◽  
Increasing Temperature

The hot deformation behavior of a high strength low alloy (HSLA) steel for construction application under hot working conditions in the temperature range of 900 to 1100 and strain rate range from 0.1 to 10 s-1 has been studied by performing a series of hot compression tests. The dynamic materials model has been employed for developing the processing maps, which show variation of the efficiency of power dissipation with temperature and strain rate. Also the Kumars model has been used for developing the instability map, which shows variation of the instability for plastic deformation with temperature and strain rate. The efficiency of power dissipation increased with decreasing strain rate and increasing temperature. High efficiency of power dissipation over 20 % was obtained at a finite strain level of 0.3 under the conditions of strain rate lower than 1 s-1 and temperature higher than 1050. Plastic instability was expected in the regime of temperatures lower than 1000°C and strain rate lower than 0.3 s-1.

scholarly journals Hot Workability of 300M Steel Investigated by In Situ and Ex Situ Compression Tests

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 880 ◽  
Author(s):  
Rongchuang Chen ◽  
Haifeng Xiao ◽  
Min Wang ◽  
Jianjun Li
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Hot Working ◽  
Ex Situ ◽  
Lower Strain Rate ◽  
Hot Workability ◽  
Compression Tests ◽  
300M Steel ◽  
Lower Strain

In this work, hot compression experiments of 300M steel were performed at 900–1150 °C and 0.01–10 s−1. The relation of flow stress and microstructure evolution was analyzed. The intriguing finding was that at a lower strain rate (0.01 s−1), the flow stress curves were single-peaked, while at a higher strain rate (10 s−1), no peak occurred. Metallographic observation results revealed the phenomenon was because dynamic recrystallization was more complete at a lower strain rate. In situ compression tests were carried out to compare with the results by ex situ compression tests. Hot working maps representing the influences of strains, strain rates, and temperatures were established. It was found that the power dissipation coefficient was not only related to the recrystallized grain size but was also related to the volume fraction of recrystallized grains. The optimal hot working parameters were suggested. This work provides comprehensive understanding of the hot workability of 300M steel in thermal compression.

Critical Strain for the Initiation of Dynamic Recrystallization in a Ni-Fe Base Alloy

2004 ◽  
Vol 449-452 ◽  
pp. 577-580
Author(s):  
Young Sang Na ◽  
Young Mok Rhyim ◽  
J.Y. Lee ◽  
Jae Ho Lee
Keyword(s):  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Critical Strain ◽  
Base Alloy ◽  
Strain Rate Range ◽  
Boundary Phase ◽  
Alloy 718 ◽  
Compression Tests ◽  
Temperature Range ◽  
Critical Strains

In order to quantitatively analyze the critical strain for the initiation of dynamic recrystallization in Ni-Fe-based Alloy 718, a series of uniaxial compression tests was conducted in the temperature range 927°C - 1066°C and the strain rate range 5 x 10-4s-1- 5 s-1with varying initial grain size. The critical strains were graphically determined based on one parameter approach and microscopically confirmed. The effect of γ'' (matrix-hardening phase) and δ (grain boundary phase)on the critical strain was simply discussed. The constitutive model for the critical strain of Alloy 718 was constructed using the experimental data obtained from the higher strain rate and the temperature range between 940°C and 1040°C.

scholarly journals Effect of Strain Rate on Hot Ductility of a Duplex Stainless Steel

2019 ◽  
Vol 2019 ◽  
pp. 1-6 ◽  
Author(s):  
Zhenhua Wang ◽  
Wenyuan Ma ◽  
Chengming Wang
Keyword(s):  
Strain Rate ◽  
Hot Forging ◽  
Total Elongation ◽  
Strain Rate Range ◽  
Hot Ductility ◽  
Hot Workability ◽  
Crack Tips ◽  
The Difference ◽  
Edge Cracking ◽  
Reduction In Area

Duplex stainless steels (DSSs) often have bad hot workability. In this study, specimens of 2205 DSS were hot tensioned over a strain rate range from 0.005 s–1 to 50 s–1 to examine the hot ductility. The crack morphology was observed, and the dependence of hot ductility on the strain rate was analyzed. From 0.005 s–1 to 0.5 s–1, both the total elongation and the reduction in area increased with the strain rate. The reduction in area exhibited a small decrease when the strain rate was greater than 0.5 s–1. More than 85% of cracks formed between the ferrite and austenite, and no less than 70% of crack tips propagated between the ferrite and austenite. When the strain rate was increased from 0.005 s–1 to 0.5 s–1, dynamic recrystallization was promoted in the austenite, and the number fraction of low-angle grain boundaries in the ferrite was improved. The higher strain rate reduced the difference between ferrite and austenite in hardness, which improved the hot ductility. For 2205 DDS, the suggested strain rate is 0.5 s–1 and above to avoid surface and edge cracking during hot forging or hot rolling. The findings will be of value for the understanding of hot ductility of DSSs and other dual-phase alloys.

Determination of Instability in Zr-2.5Nb-0.5Cu Using Lyapunov Function

2015 ◽  
Vol 830-831 ◽  
pp. 329-332 ◽  
Author(s):  
Kuldeep Kumar Saxena ◽  
Vivek Pancholi ◽  
Dinesh Srivastava ◽  
G.K. Dey ◽  
Sanjay K. Jha ◽  
...  
Keyword(s):  
Lyapunov Function ◽  
Strain Rate ◽  
Flow Instability ◽  
Peak Stress ◽  
Strain Rate Range ◽  
Rate Of Change ◽  
Deformation Condition ◽  
Hot Workability ◽  
Lower Temperature

Hot workability of Zr-2.5Nb-0.5Cu alloy has been investigated by means of hot compression test using Gleeble-3800®, in the temperature and strain rate range of 700 to 925°C and 0.01-10s-1, respectively. Deformation behavior was characterized in terms of flow instability using peak stress with the help of Lyapunov Function. The true stress-strain curves shows that softening occurs at all lower temperature and for entire strain rates of deformation. The instable flow was suggested by negative m value at deformation condition of 700°C (5 and 10 s-1), while s value at 925°C (10 s-1). The combined result of rate of change of m and s with respect to log strain rate suggest that the deformation condition ranges from 725-780°C (10-2- 10-1 s-1) and 700°C (1-10 s-1) representing safe domain for stable flow.

Strain Rate Sensitivity of Ultrafine-Grained CP-Ti Processed by ECAP at Room Temperature

2010 ◽  
Vol 667-669 ◽  
pp. 707-712 ◽  
Author(s):  
Xiao Yan Liu ◽  
Xi Cheng Zhao ◽  
Xi Rong Yang
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rate Range ◽  
Compression Tests ◽  
Ultrafine Grained ◽  
Die Set ◽  
Increasing Temperature ◽  
Cp Ti

Ultrafine-grained (UFG) commercially pure (CP) Ti with a grain size of about 200 nm was produced by ECAP up to 8 passes using route BC at room temperature. For ECAP processing a proper die set was designed and constructed with an internal channel angle Φ of 120° and an outer arc of curvature Ψ of 20°. Strain rate sensitivity of UFG CP-Ti and CG CP-Ti were investigated by compression tests in the temperature range of 298~673K and strain rate range of 10-4~100s-1 using Gleeble simulator machine. Evolution of the microstructure during compression testing was observed using optical microscopy (OM) and transmission electron microscopy (TEM). Strain rate sensitivity value m of the UFG CP-Ti has been measured and is found to increase with increasing temperature and decreasing strain rate, and is enhanced compared to that of CG CP-Ti. Result of the deformation activation energy determination of UFG CP-Ti indicates that the deformation mechanism in UFG CP-Ti is correlated to the grain boundaries.

Characterization of Hot Deformation Behavior of Udimet720Li Superalloy Using Processing Map

2014 ◽  
Vol 887-888 ◽  
pp. 1161-1168
Author(s):  
Jian Guo Wang ◽  
Dong Liu ◽  
Tao Wang ◽  
Yan Hui Yang
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
High Strain ◽  
Flow Behavior ◽  
Strain Range ◽  
Peak Stress ◽  
Strain Rate Range ◽  
Hot Working ◽  
Compression Tests ◽  
Hollomon Parameter

The deformation behavior of a Udimet720Li superalloy under hot compression tests was characterized in the temperature range of 1060~1160°C and strain rate range of 0.001~20s-1. Processing maps were conducted at a series of strains to calculate the efficiency of hot working and to recognize the instability regions of the flow behavior. A Zener-Hollomon parameter is given to characterize the dependence of peak stress on temperature and strain rate. The efficiency of power dissipation of the Udimet720Li superalloy obtained in a strain range of 0.1~0.7 are essentially similar, which indicates that strain does not have a significant influence and the instability region shown in high strain and high strain rates at all temperatures. The regions for the full recrystallization can be divided by the dissolution beginning temperature of primary γ'which are the optimum hot working parameters.

A Study on the Effects of Strain Rates on Characteristics of Brain Tissue

2017 ◽  
Author(s):  
Mohammad Hosseini Farid ◽  
Ashkan Eslaminejad ◽  
Mariusz Ziejewski ◽  
Ghodrat Karami
Keyword(s):  
Strain Rate ◽  
Brain Tissue ◽  
Mechanical Load ◽  
Experimental Studies ◽  
High Rate ◽  
Dynamic Strain ◽  
Strain Rates ◽  
Compression Tests ◽  
Static Strain ◽  
The Brain

Traumatic brain injury (TBI) often happens when the brain tissue undergoes a high rate mechanical load. Although numerous research works have been carried out to study the mechanical characterization of brain matter under quasi-static (strain rate ≤ 100 S−1) loading but a limited amount of experimental studies are available for brain tissue behavior under dynamic strain rates (strain rate ≥ 100 S−1). In this paper, the results of a study on mechanical properties of ovine brain tissue under unconfined compression tests are to be presented. The samples were compressed under uniaxial strain rates of 0.0667, 3.33, 6.667, 33.33, 66.667 and 200 S−1. The brain tissue presents a stiffer response with increasing strain rate, showing a time-dependent behavior. So the hyperelastic-only models are not adequate to exhibit the brain viscoelasticity. Therefore, two hyper-viscoelastic constitutive equations based on power function model and Mooney-Rivlin energy function are applied to the results with quasi-static strain rate (≤ 100 S−1). Good agreement of experimental and theoretical has been achieved for results of the low strain rates. It is concluded that the obtained material parameters from quasi-static tests are not appropriate enough to fit the result with the high strain rate of 200 S−1. The study will further provide new insight into a better understanding of the rate-dependency behavior of the brain tissue under dynamic conditions. This is essential in the development of constitutive material characteristics for an efficient human brain finite element models to predict TBI under impact condition or high motion.

Hot Deformation Behavior and Microstructural Evolution of Mg-Nd-Zn-Zr Magnesium Alloy

2013 ◽  
Vol 747-748 ◽  
pp. 320-326 ◽  
Author(s):  
Wen Xiang Wu ◽  
Li Jin ◽  
Jie Dong ◽  
Zhen Yan Zhang ◽  
Wen Jiang Ding
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Grain Boundaries ◽  
Microstructural Evolution ◽  
Hot Deformation ◽  
Fine Particles ◽  
Volume Fraction ◽  
Strain Rate Range ◽  
Compression Tests ◽  
Average Size

The hot deformation behaviors and microstructural evolution of Mg-3.0Nd-0.2Zn-0.4Zr (wt. %, NZ30K) alloy were investigated by means of the isothermal hot compression tests at temperatures of 350-500 °C with strain rates of 0.001, 0.01, 0.1 and 1s-1. The results showed that the flow stress increased to a peak and then decreased which showed a dynamic flow softening. The flow stress behavior was described by the hyperbolic sine constitutive equation with an average activation energy of 193.8 kJ/mol. The average size of dynamically recrystallized grains of hot deformed NZ30K alloy was reduced by increasing the strain rate and/or decreasing the deformation temperature. A large amount of fine particles precipitated in the grains interior and at the grain boundaries when heated to the compression temperatures and soaked for 5min below 450 °C. However, the volume fraction of particles decreased significantly when soaked for 5 min at 500 °C, and the coarse particles precipitated mainly at the grain boundaries. Hot deformation at the temperature of 500 °C around and at the strain rate range of 0.1s-1 was desirable for NZ30K alloy.

Sign in / Sign up

Export Citation Format

Share Document