Evolution of Microstructure in Brazed Joints of Austenitic-Martensitic Stainless Steel with Pure Silver Obtained with Ag-27Cu-5Sn Brazing Filler Material

2016 ◽  
Vol 47 (12) ◽  
pp. 6148-6159 ◽  
Author(s):  
S. Gangadharan ◽  
D. Sivakumar ◽  
T. Venkateswaran ◽  
Kaustubh Kulkarni
Keyword(s):  
Stainless Steel ◽  
Martensitic Stainless Steel ◽  
Filler Material ◽  
Pure Silver ◽  
Brazed Joints ◽  
Evolution Of Microstructure

Evolution of microstructure of 304 stainless steel joined by brazing process

2010 ◽  
Vol 1276 ◽  
Author(s):  
F. García-Vázquez ◽  
I. Guzmán-Flores ◽  
A. Garza ◽  
J. Acevedo
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Holding Time ◽  
304 Stainless Steel ◽  
Commercial Application ◽  
Wide Range ◽  
Unique Method ◽  
Brazed Joints ◽  
Brazed Joint ◽  
Evolution Of Microstructure

AbstractBrazing is a unique method to permanently join a wide range of materials without oxidation. It has wide commercial application in fabricating components. This paper discusses results regarding the brazing process of 304 stainless steel. The experimental brazing is carried out using a nickel-based (Ni-11Cr-3.5Si-2.25B-3.5Fe) filler alloy. In this process, boron and silicon are incorporated to reduce the melting point, however they form hard and brittle intermetallic compounds with nickel (eutectic phases) which are detrimental to the mechanical properties of brazed joints. This investigation deals with the effects of holding time and brazing temperature on the microstructure of joint and base metal, intermetallic phases formation within the brazed joint as well as measurement of the tensile strength. The results show that a maximum tensile strength of 464 MPa is obtained at 1120°C and 4 h holding time. The shortest holding times will make boron diffuse insufficiently and generate a great deal of brittle boride components.

Effects of Ni and Co Additions to Filler Metals on Ag-Brazed Joints of Cemented Carbide and Martensitic Stainless Steel

2014 ◽  
Vol 922 ◽  
pp. 322-327 ◽  
Author(s):  
Kengo Kaiwa ◽  
Shinji Yaoita ◽  
Tomohiro Sasaki ◽  
Takehiko Watanabe
Keyword(s):  
Stainless Steel ◽  
Joint Strength ◽  
Martensitic Stainless Steel ◽  
Braze Alloy ◽  
Cemented Carbide ◽  
Suppression Effect ◽  
Brazed Joints ◽  
Co Addition ◽  
Multiple Addition ◽  
Filler Metals

This study focuses on understanding the effect of Ni and Co additions to filler metals on Ag-brazed joints of cemented carbide and martensitic stainless steel. Ni and Co added braze alloys were processed based on Ag-Cu-Zn ternary alloy, and joint strength and microstructure of the brazed layer has been investigated. The joint strength increased by the 2.0mass%Ni and 0.5mass%Co addition into braze alloy. This trend is remarkable in the Co added alloy, and the brazed joint increased by 141% compared to that in no-added alloy. The joint strength was closely related to the suppression effect of Co dissolution from cemented carbide into filler layer and Fe diffusion from the stainless steel to the brazed layer. In the brazed microstructure, Co-depleted zone caused by dissolution of Co in the cemented carbide was observed near the interface between the cemented carbide and the steel. Width of the Co-depleted zone significantly decreased in the Co added alloy. However, the joint strength decreased in the multiple addition compared to that in the single addition of Ni or Co.

Fracture Behaviour of Brazed Soft Martensitic Stainless Steel Joints under Cyclic Loading

2010 ◽  
Vol 636-637 ◽  
pp. 1490-1495 ◽  
Author(s):  
Tanya A. Başer ◽  
Christian Leinenbach ◽  
Hans Jakob Schindler
Keyword(s):  
Stainless Steel ◽  
Fatigue Crack ◽  
Cyclic Loading ◽  
Martensitic Stainless Steel ◽  
Fracture Behaviour ◽  
Growth Curves ◽  
Threshold Values ◽  
Brazed Joints ◽  
Steel Joints ◽  
Very High

The fracture behaviour of brazed joints of the soft martensitic stainless steel X3CrNiMo13-4 under cyclic loading is investigated. The fatigue crack propagation curves (da/dN-ΔK) were derived for different load ratios R. The fatigue crack threshold values ΔKth were estimated to be 9 MPa m0.5, 7 MPa m0.5, 6 MPa m0.5 and 4 MPa m0.5 for the R values of 0.1, 0.3, 0.5 and 0.7, respectively. In addition, crack growth curves were derived for different constant loads ΔF. The Paris exponent, n, was estimated for the different R values and found to be very high compared to homogeneous materials. The work was completed with microstructural and fractographic investigation by scanning electron microscope (SEM).

CTS-BD30P ALLOY

Alloy Digest ◽  
2013 ◽  
Vol 62 (8) ◽  
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Martensitic Stainless Steel ◽  
Heat Treating ◽  
Powder Metal ◽  
High Concentration ◽  
Vanadium Carbides

Abstract Carpenter CTS-BD30P alloy is a powder metal processed, air-hardening, martensitic stainless steel that offers corrosion resistance comparable with Type 440C stainless, combined with excellent toughness and wear resistance attributed to a high concentration of vanadium carbides. The Carpenter CTS family of alloys is used for many blade applications. This datasheet provides information on composition and physical properties. It also includes information on corrosion resistance as well as heat treating and powder metal forms. Filing Code: SS-1154. Producer or source: Carpenter Specialty Alloys.

LESCALLOY 15-5 VAC-ARC

Alloy Digest ◽  
1991 ◽  
Vol 40 (8) ◽  
Keyword(s):  
Stainless Steel ◽  
Precipitation Hardening ◽  
Martensitic Stainless Steel ◽  
Heat Treating ◽  
Gas Content ◽  
Vacuum Arc ◽  
Steel Company ◽  
Delta Ferrite ◽  
Clean Steel ◽  
Vacuum Arc Remelting

Abstract LESCALLOY 15-5 VAC-ARC is a precipitation hardening martensitic stainless steel with minimal delta ferrite. Vacuum arc remelting in the production of the alloy provides a low gas content, clean steel with optimum transverse properties. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-522. Producer or source: Latrobe Steel Company.

CRUCIBLE CPM S30V

Alloy Digest ◽  
2003 ◽  
Vol 52 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Stainless Steel ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Martensitic Stainless Steel ◽  
Heat Treating ◽  
Corrosion And Wear ◽  
Better Than

Abstract Crucible CPM S30V is a martensitic stainless steel designed with a combination of toughness, wear resistance, and corrosion resistance equal to or better than 440C. This datasheet provides information on composition, physical properties, microstructure, hardness, and elasticity as well as fracture toughness. It also includes information on corrosion and wear resistance as well as heat treating and machining. Filing Code: SS-891. Producer or source: Crucible Service Centers.

Sign in / Sign up

Export Citation Format

Share Document