Intermetallics Characterization of Lead-Free Solder Joints under Isothermal Aging

2008 ◽  
Vol 37 (8) ◽  
pp. 1130-1138 ◽  
Author(s):  
Anupam Choubey ◽  
Hao Yu ◽  
Michael Osterman ◽  
Michael Pecht ◽  
Fu Yun ◽  
...  
Keyword(s):  
Isothermal Aging ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Free Solder

Effects of Current Stressing and Isothermal Aging on the Tensile Strength of Microscale Lead-Free Solder Joints with Different Joint Volumes

2013 ◽  
Vol 634-638 ◽  
pp. 2800-2803 ◽  
Author(s):  
Li Meng Yin ◽  
Yan Fei Geng ◽  
Zhang Liang Xu ◽  
Song Wei
Keyword(s):  
Tensile Strength ◽  
Current Density ◽  
Isothermal Aging ◽  
Solder Joints ◽  
High Current Density ◽  
Copper Wire ◽  
Lead Free ◽  
Lead Free Solder ◽  
Current Stressing ◽  
Free Solder

Adopting an accurate micro-tensile method based on dynamic mechanical analyzer (DMA) instrument, the tensile strength of three kinds of copper-wire/solder/copper-wire sandwich structured microscale lead-free solder joints that underwent current stressing with a direct current density of 1.0×104 A/cm2 and loading time of 48 hours were investigated, and compared with those solder joints isothermal aged at 100 0C for 48 hours and as-reflowed condition. These three kinds of microscale columnar solder joints have different volumes, i.e., a same diameter of 300 μm but different heights of 100 μm, 200 μm and 300 μm. Experimental results show that both current stressing and isothermal aging degrades the tensile strength of microscale solder joints, and the solder joint with smaller volume obtains higher tensile strength under same test condition. In addition, current stressing induces obvious electromigration (EM) issue under high current density of 1.0×104 A/cm2, resulting in the decreasing of tensile strength and different fracture position, mode and surface morphology of microscale solder joints. The degree of strength degradation increases with the increasing of joint height when keep joint diameter constant, this is mainly due to that electromigration leads to voids form and grow at the interface of cathode, and solder joints with larger volume may contains more soldering defects as well.

Nanoindentation Measurements of the Mechanical Properties of Individual Phases Within Lead Free Solder Joints Subjected to Isothermal Aging

2018 ◽  
Author(s):  
Abdullah Fahim ◽  
Sudan Ahmed ◽  
Jeffrey C. Suhling ◽  
Pradeep Lall
Keyword(s):  
Mechanical Properties ◽  
Isothermal Aging ◽  
Solder Joints ◽  
Bulk Solder ◽  
Lead Free ◽  
Nanoindentation Test ◽  
Lead Free Solder ◽  
Free Solder ◽  
The Individual ◽  
Sac Solder

Exposure of lead free solder joints to high temperature isothermal aging conditions leads to microstructure evolution, which mainly includes coarsening of the intermetallic (IMC) phases. In our previous work, it was found that the coarsening of IMCs led to degradation of the overall mechanical properties of the SAC solder composite consisting of β-Sn matrix and IMC particles. However, it is not known whether the isothermal aging changes properties of the individual β-Sn and IMC phases, which could also be affecting to the overall degradation of properties. In this study, the aging induced variations of the mechanical properties of the β-Sn phase, and of Sn-Cu IMC particles in SAC solder joints have been explored using nanoindentation. SAC solder joints extracted from SuperBGA (SBGA) packages were aged for different time intervals (0, 1, 5, 10 days) at T = 125 °C. Nanoindentation test samples were prepared by cross sectioning the solder joints, and then molding them in epoxy and polishing them to prepare the joint surfaces for nanoindentation. Multiple β-Sn grains were identified in joints using optical polarized microscopy and IMCs were also observed. Individual β-Sn grains and IMC particles were then indented at room temperature to measure their mechanical properties (elastic modulus and hardness) and time dependent creep deformations. Properties measured at different aging time were then compared to explore aging induced degradations of the individual phases. The properties of the individual phases did not show significant degradation. Thus, IMC coarsening is the primary reason for the degradation of bulk solder joint properties, and changes of the properties of the individual phases making up the lead free solder material are negligible.

Evaluation of thermomechanical fatigue lifetime of BGA lead-free solder joints and impact of isothermal aging

2021 ◽  
pp. 114201 ◽  
Author(s):  
Pierre Roumanille ◽  
Emna Ben Romdhane ◽  
Samuel Pin ◽  
Patrick Nguyen ◽  
Jean-Yves Delétage ◽  
...  
Keyword(s):  
Isothermal Aging ◽  
Solder Joints ◽  
Thermomechanical Fatigue ◽  
Lead Free ◽  
Lead Free Solder ◽  
Fatigue Lifetime ◽  
Free Solder

Isothermal Aging Effects on the Mechanical Shock Performance of Lead-Free Solder Joints

2011 ◽  
Vol 1 (5) ◽  
pp. 714-721 ◽  
Author(s):  
Hongtao Ma ◽  
Tae-Kyu Lee ◽  
Dong Hyun Kim ◽  
H G Park ◽  
Sang Ha Kim ◽  
...  
Keyword(s):  
Isothermal Aging ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Mechanical Shock ◽  
Aging Effects ◽  
Free Solder

Characterization of aging effects in lead free solder joints using nanoindentation

2013 ◽  
Author(s):  
Mohammad Hasnine ◽  
Muhannad Mustafa ◽  
Jeffrey C. Suhling ◽  
Barton C. Prorok ◽  
Michael J. Bozack ◽  
...  
Keyword(s):  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Aging Effects ◽  
Free Solder

Characterization of Recrystallization and Microstructure Evolution in Lead-Free Solder Joints Using EBSD and 3D-XRD

2012 ◽  
Vol 42 (2) ◽  
pp. 319-331 ◽  
Author(s):  
Bite Zhou ◽  
Thomas R. Bieler ◽  
Tae-Kyu Lee ◽  
Wenjun Liu
Keyword(s):  
Microstructure Evolution ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Free Solder
Sign in / Sign up

Export Citation Format

Share Document