Mechanical and Corrosion Behavior of Inconel 718 Nickel-Based Super Alloy Doped with Graphene Nanoplatelets

2019 ◽  
Vol 19 (5) ◽  
pp. 1493-1497 ◽  
Author(s):  
Khotso Khoele ◽  
David Jacobus Delport
Keyword(s):  
Corrosion Behavior ◽  
Inconel 718 ◽  
Graphene Nanoplatelets ◽  
Super Alloy

Corrosion Behavior of a Selective Laser Melted Inconel 718 Alloy in a 3.5 wt.% NaCl Solution

2021 ◽  
Author(s):  
Yanbing Tang ◽  
Xinwang Shen ◽  
Yanxin Qiao ◽  
Lanlan Yang ◽  
Jian Chen ◽  
...  
Keyword(s):  
Corrosion Behavior ◽  
Inconel 718 ◽  
Nacl Solution ◽  
Inconel 718 Alloy

Study on surface defects in milling Inconel 718 super alloy

2015 ◽  
Vol 29 (4) ◽  
pp. 1723-1730 ◽  
Author(s):  
Chang Liu ◽  
Chengzu Ren ◽  
Guofeng Wang ◽  
Yinwei Yang ◽  
Lu Zhang
Keyword(s):  
Inconel 718 ◽  
Surface Defects ◽  
Super Alloy

scholarly journals Investigation of low stress rupture properties in Inconel-718 super alloy

2016 ◽  
Vol 146 ◽  
pp. 012051 ◽  
Author(s):  
T. Zaman ◽  
M. Farooque ◽  
S. A. Rizvi ◽  
I. Salam ◽  
M. Waseem
Keyword(s):  
Inconel 718 ◽  
Stress Rupture ◽  
Stress Rupture Properties ◽  
Rupture Properties ◽  
Super Alloy

Research on Drilling Process of Nickel-Based Super-Alloy

2010 ◽  
Vol 33 ◽  
pp. 373-377
Author(s):  
Jian Wu ◽  
Rong Di Han
Keyword(s):  
Feed Rate ◽  
Empirical Formula ◽  
Inconel 718 ◽  
Thrust Force ◽  
Shear Angle ◽  
Drilling Process ◽  
Deformation Characteristics ◽  
Drilling Speed ◽  
Aisi 1045 ◽  
Super Alloy

Nickel-based super-alloy belongs to difficult-to-machine materials, its machinability is low. To find out the difficulties of drilling nickel-based super-alloy, it is necessary to study the drilling process. The study on the drilling process of nickel-based super-alloy Inconel 718 is discussed from two aspects, drilling deformation and drilling forces distribution. For studying the drilling deformation characteristics and influence laws, the drilling chip specimens are obtained by using self-made drilling quick-stop device. Then, the empirical formula of shear angle is also given. Finally, the drilling forces distribution is studied. Results shows that: drilling deformation decreases when the distance to chisel edge, drilling speed and feed rate increases; drilling deformation of Inconel 718 is larger than AISI 1045; the ratio of torque and thrust force on the lead cutting edge is 29%~33%, 74%~77%, respectively; the torque and thrust force of Inconel 718 is about 1.8~2.3 times than that of AISI 1045.

scholarly journals Effect of Aging Condition on Fatigue Properties of Ni-Base Super Alloy Inconel 718 at Room Temperature

2008 ◽  
Vol 74 (743) ◽  
pp. 994-999 ◽  
Author(s):  
Norio KAWAGOISHI ◽  
Shogo YOSHIMI ◽  
Masahiro GOTO ◽  
Yuzo NAKAMURA ◽  
Yoshihisa OHZONO
Keyword(s):  
Inconel 718 ◽  
Room Temperature ◽  
Fatigue Properties ◽  
Aging Condition ◽  
Super Alloy
Sign in / Sign up

Export Citation Format

Share Document