Mechanical Properties of AA 7075/Al2O3/SiC Nano-metal Matrix Composites by Stir-Casting Method

2019 ◽  
Vol 100 (1) ◽  
pp. 43-53 ◽  
Author(s):  
S. Suresh ◽  
G. Harinath Gowd ◽  
M. L. S. Deva Kumar
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Stir Casting ◽  
Matrix Composites ◽  
Casting Method ◽  
Aa 7075

Production of Al Metal Matrix Composites by the Stir-Casting Method

2013 ◽  
Vol 592-593 ◽  
pp. 614-617 ◽  
Author(s):  
Konstantinos Anthymidis ◽  
Kostas David ◽  
Pavlos Agrianidis ◽  
Afroditi Trakali
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Automobile Industry ◽  
Metal Matrix ◽  
Aluminum Matrix ◽  
Stir Casting ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Casting Method ◽  
Alloy Matrix

It is well known that the addition of ceramic phases in an alloy e.g. aluminum, in form of fibers or particles influences its mechanical properties. This leads to a new generation of materials, which are called metal matrix composites (MMCs). They have found a lot of application during the last twenty-five years due to their low density, high strength and toughness, good fatigue and wear resistance. Aluminum matrix composites reinforced by ceramic particles are well known for their good thermophysical and mechanical properties. As a result, during the last years, there has been a considerable interest in using aluminum metal matrix composites in the automobile industry. Automobile industry use aluminum alloy matrix composites reinforced with SiC or Al2O3 particles for the production of pistons, brake rotors, calipers and liners. However, no reference could be cited in the international literature concerning aluminum reinforced with TiB particles and Fe and Cr, although these composites are very promising for improving the mechanical properties of this metal without significantly alter its corrosion behavior. Several processing techniques have been developed for the production of reinforced aluminum alloys. This paper is concerned with the study of TiB, Fe and Cr reinforced aluminum produced by the stir-casting method.

Study on Mechanical Properties of Al 7075 Hybrid Metal Matrix Composites

2015 ◽  
Vol 813-814 ◽  
pp. 230-234 ◽  
Author(s):  
T.S.A. Suryakumari ◽  
S. Ranganathan ◽  
P. Shankar
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Stir Casting ◽  
Impact Loads ◽  
Matrix Composites ◽  
Casting Method ◽  
Weight Percentage ◽  
Hybrid Metal Matrix Composites ◽  
Al 7075

The present investigation involves studying the mechanical properties of the fabricated aluminium 7075 hybrid metal matrix composites reinforced with various weight % of SiC and Al2 O3 particulates by stir casting method. The Al 7075 hybrid metal matrix composites specimen were fabricated using L9 orthogonal array. The mechanical properties like Brinell Harness (BHN), Rockwell Hardness (HRC) and impact loads were experimented. The mechanical properties like hardness and impact loads have improved with the increase in weight percentage of SiC and Al2O3 particulates in the hybrid aluminium matrix.

Material Characterization Study on Aluminium Metal Matrix Composites by Enhanced Stir Casting Method

2014 ◽  
Vol 984-985 ◽  
pp. 326-330
Author(s):  
T.M. Chenthil Jegan ◽  
D. Ravindran ◽  
M. Dev Anand
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Tensile Strength ◽  
Boron Carbide ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Stir Casting ◽  
Aluminium Matrix ◽  
Matrix Composites ◽  
Casting Method

Metal Matrix Composites possesses high mechanical properties compared to unreinforced materials. Aluminium Matrix Composites (AMC) is attracted in the emerging world because of its low cost, less weight and enhanced mechanical properties. In the present study the enhancement in mechanical properties like hardness and tensile strength of AMCs by reinforcing AA 6061 matrix with silicon carbide (SiC) and boron carbide (B4C) particles are analyzed. By enhanced stir casting method aluminium matrix was reinforced with boron carbide particulates and silicon carbide particulates with the various weight percentage of 2.5 %,5% and 7.5%.The tensile strength and hardness was found to increase with the increase in wt% of the reinforcement. From the analysis it is observed that the mechanical property of B4C reinforced AMC is significantly good compared to SiC reinforced AMC.

scholarly journals Properties of AlSi9Cu3 metal matrix micro and nano composites produced via stir casting

2018 ◽  
Vol 16 (1) ◽  
pp. 726-731 ◽  
Author(s):  
Tennur Gülşen Ünal ◽  
Ege Anıl Diler
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix ◽  
Weight Fraction ◽  
Stir Casting ◽  
Mechanical Tests ◽  
Matrix Composites ◽  
Casting Method ◽  
Porosity Formation ◽  
Three Point Bending ◽  
Hardness Values

AbstractThe effects of micro and nano sized reinforcement particles on microstructure and mechanical properties of aluminium alloy-based metal matrix composites were investigated in this study. AlSi9Cu3 alloy was reinforced with micro and nano sized ceramic reinforcement particles at different weight fractions by using a stir casting method. The mechanical tests (hardness, three point bending) were performed to determine the mechanical properties of AlSi9Cu3 alloy-based microcomposites (AMMCs) and nanocomposites (AMMNCs). The experimental results have shown that the size and weight fraction of reinforcement particles have a strong influence on the microstructure and the mechanical properties of AlSi9Cu3 alloy-based microcomposites and nanocomposites. The relative densities of all AMMC and AMMNC samples are lower than unreinforced AlSi9Cu3 alloy due to porosity formation with the increase of weight fraction of reinforcement particles. As weight fraction increases, hardness values of AMMCs and AMMNCs increase. Maximum flexural strength can be obtained at 3.5wt.% for the AMMC sample with microsized Al2O3 particles and at 2wt.% for the AMMNC sample with nano-sized Al2O3 particles. After the weight fractions exceed these values, flexural strengths of both AMMCs and AMMNCs decrease due to clustering of Al2O3 particles.

Sign in / Sign up

Export Citation Format

Share Document