scholarly journals Formability study and metallurgical properties analysis of FSWed AA 6061 blank by the SPIF process

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
Payam Tayebi ◽  
Ali Fazli ◽  
Parviz Asadi ◽  
Mahdi Soltanpour
Keyword(s):  
Base Metal ◽  
Strain Distribution ◽  
Thickness Distribution ◽  
Experimental Studies ◽  
Welding Process ◽  
Forming Limit ◽  
Forming Process ◽  
Friction Stir ◽  
Numerical Process ◽  
Tailor Welded Blank

AbstractIn this study, in order to obtain the maximum possible formability in tailor-welded blank AA6061 sheets connected by the friction stir welding (FSW) procedure, the incremental sheet forming process has been utilized. The results are presented both numerically and experimentally. To obtain the forming limit angle, the base and FSWed sheets were formed in different angles with conical geometry, and ultimately, the forming limit angle for the base metal and FSWed sheet is estimated to be 60° and 57.5°, respectively. To explore the effects of welding and forming procedures on AA6061 sheets, experimental studies such as mechanical properties, microstructure and fracture analysis are carried out on the samples. Also, the thickness distribution of the samples is studied to investigate the effect of the welding process on the thickness distribution. Then, the numerical process was simulated by the ABAQUS commercial software to study the causes of the FSWed samples failure through analyzing the thickness distribution parameter, and major and minor strains and the strain distribution. Causes of failure in FSWed samples include increased minor strain, strain distribution and thickness distribution in welded areas, especially in the proximity of the base metal area.

Material Flow Behavior Modelling and Strain Distribution Prediction During Self-Reacting Friction Stir Welding Process Based on Computational Fluid Dynamics Method

2020 ◽  
Author(s):  
Chenyu Zhao ◽  
Xun Liu ◽  
Wei Zhang ◽  
Weiyu Cao
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Friction Stir Welding ◽  
Strain Distribution ◽  
Process Model ◽  
Flow Behavior ◽  
Experimental Studies ◽  
Welding Process ◽  
Friction Stir ◽  
Stress Boundary

Abstract Self-reacting friction stir welding (SRFSW) is an advanced variant of friction stir welding (FSW) and shows several superiorities with the double-sided tool configuration. Despite the considerable amount of experimental studies in this field, most of the tool development efforts are still empirical and resort to trial-and-error solutions. To reveal effects of tool features on process physics and guide tool designs, in this study, a multi-physics SRFSW process model is developed within the framework of computational fluid dynamics (CFD). A shear stress boundary condition is applied at the tool-workpiece contact interface. First, the velocity distribution at weld cross section are calculated and the results show that the threads on the pin contribute to the enhancement of stirring effect. Second, the temperature evolutions at advancing side (AS) and retreating side (RS) are compared, and position in RS has higher temperature than position in AS accordingly. Finally, the plastic strain distribution behind pin tool is calculated by integrating effective stain rate along pathlines. The result shows that AS has a more definable strain boundary than RS, which corresponds to the general macroscopic observations in SRFSW. The results may provide a reference on SRFSW tool design.

Optimization of Sheet Metal Process Parameters of a Shield Case Piece Using Computer Simulation

2006 ◽  
Vol 510-511 ◽  
pp. 330-333
Author(s):  
M.C. Curiel ◽  
Ho Sung Aum ◽  
Joaquín Lira-Olivares
Keyword(s):  
Sheet Metal ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Physical Processes ◽  
Forming Process ◽  
Element Analysis ◽  
One Step ◽  
Range Of Values ◽  
Principal Strains

Numerical simulations based on Finite Element Analysis (FEA) are widely used to predict and evaluate the forming parameters before performing the physical processes. In the sheet metal industry, there are basically two types of FE programs: the inverse (one-step) programs and the incremental programs. In the present paper, the forming process of the shield case piece (LTA260W1-L05) was optimized by performing simulations with both types of software. The main analyzed parameter was the blankholding force while the rest of the parameters were kept constant. The criteria used to determine the optimum value was based on the Forming Limit Diagram (FLD), fracture and wrinkling of the material, thickness distribution, and the principal strains obtained. It was found that the holding force during the forming process deeply affects the results, and a range of values was established in which the process is assumed to give a good quality piece.

scholarly journals Increasing of the Mechanical Properties of Friction Stir Welded Joints of 6061 Aluminum Alloy by Introducing Alumina Particles

2017 ◽  
Vol 17 (2) ◽  
pp. 29-40 ◽  
Author(s):  
M. A. Tashkandi ◽  
J. A. Al-Jarrah ◽  
M. Ibrahim
Keyword(s):  
Aluminum Alloy ◽  
Base Metal ◽  
Welded Joints ◽  
Volume Fraction ◽  
Welding Process ◽  
Welding Zone ◽  
6061 Aluminum Alloy ◽  
Friction Stir ◽  
Alumina Particles ◽  
Welding Line

AbstractThe main aim of this investigation is to produce a welding joint of higher strength than that of base metals. Composite welded joints were produced by friction stir welding process. 6061 aluminum alloy was used as a base metal and alumina particles added to welding zone to form metal matrix composites. The volume fraction of alumina particles incorporated in this study were 2, 4, 6, 8 and 10 vol% were added on both sides of welding line. Also, the alumina particles were pre-mixed with magnesium particles prior being added to the welding zone. Magnesium particles were used to enhance the bonding between the alumina particles and the matrix of 6061 aluminum alloy. Friction stir welded joints containing alumina particles were successfully obtained and it was observed that the strength of these joints was better than that of base metal. Experimental results showed that incorporating volume fraction of alumina particles up to 6 vol% into the welding zone led to higher strength of the composite welded joints as compared to plain welded joints.

Study on Forming Behaviour of Friction Stir Welded Blanks During Single Point Incremental Forming (SPIF) Process

2020 ◽  
Author(s):  
Shalin Marathe ◽  
Harit Raval
Keyword(s):  
Friction Stir Welding ◽  
Incremental Forming ◽  
Single Point ◽  
Base Material ◽  
Forming Limit ◽  
Single Point Incremental Forming ◽  
Cnc Milling ◽  
Forming Process ◽  
Friction Stir ◽  
Welding Processes

Abstract The automobile, transportation and shipbuilding industries are aiming at fuel efficient products. In order to enhance the fuel efficiency, the overall weight of the product should be brought down. This requirement has increased the use of material like aluminium and its alloys. But, it is difficult to weld aluminium using conventional welding processes. This problem can be solved by inventions like friction stir welding (FSW) process. During fabrication of product, FSW joints are subjected to many different processes and forming is one of them. During conventional forming, the formability of the welded blanks is found to be lower than the formability of the parent blank involved in it. One of the major reasons for reduction in formability is the global deformation provided on the blank during forming process. In order to improve the formability of homogeneous blanks, Single Point Incremental Forming (SPIF) is found to be giving excellent results. So, in this work formability of the welded blanks is investigated during the SPIF process. Friction Stir Welding is used to fabricate the welded blanks using AA 6061 T6 as base material. Welded blanks are formed in to truncated cone through SPIF process. CNC milling machine is used as SPIF machine tool to perform the experimental work. In order to avoid direct contact between weld seam and forming tool, a dummy sheet was used between them. As responses forming limit curve (FLC), surface roughness, and thinning are investigated. It was found that use of dummy sheet leads to improve the surface finish of the formed blank. The formability of the blank was found less in comparison to the parent metal involved in it. Uneven distribution of mechanical properties in the welded blanks leads to decrease the formability of the welded blanks.

Study on the Forming Process of the Crossmember in Car Intermediate Floor

2013 ◽  
Vol 442 ◽  
pp. 593-598
Author(s):  
Xue Xia Wang ◽  
Peng Chong Guan ◽  
Hai Peng Li ◽  
Li Hui Wang ◽  
Na Zhang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Model ◽  
Process Parameters ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Simulation Technology ◽  
Forming Process ◽  
Distribution Diagram ◽  
Simulation Results

Flanging and bending forming processes of the crossmember in car intermediate floor are investigated respectively by using numerical simulation technology. The numerical model of the crossmember was established and its press forming effect was simulated to determine the feasible process parameters affecting its manufacturability. Forming limit diagram and thickness distribution diagram are used to evaluate simulation results of different process schemes. And then optimum values of process parameters for flanging and bending are found, which can reduce the tendencies of wrinkling, springback and crackling during the stamping of the product.

Investigation on Forming Process of Automobile Trunk Side Panel Based on Numerical Simulation Technology

2013 ◽  
Vol 634-638 ◽  
pp. 2855-2860
Author(s):  
Hai Peng Li ◽  
Jia Wei Fan ◽  
Li Hui Wang ◽  
Xue Xia Wang ◽  
Ju Yuan Zhao
Keyword(s):  
Numerical Simulation ◽  
Process Parameters ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Simulation Technology ◽  
Forming Process ◽  
Distribution Diagram ◽  
Side Panel ◽  
Design Cycle

The forming process of automobile trunk side panel was investigated, using numerical simulation technology, to acquire the feasible process parameters and improve the formability of the product. With the technology, the manufacturability working procedures and drawing process parameters of the product were analyzed, calculated and simulated to achieve optimum formability characteristics. The method effectively lowers the probability of springback, wrinkling and thickness reduction, and shortens design cycle and cost. Based on the simulation results including forming limit diagram and thickness distribution diagram, the feasible process parameters are determined.

Experimental Study on Residual Formability of Single Point Incrementally Formed Part

2019 ◽  
Author(s):  
Chetan P. Nikhare
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Forming Limit ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Conventional Process

Abstract A substantial increase in demand on the sheet metal part usage in aerospace and automotive industries is due to the increase in the sale of these products to ease the transportation. However, due to the increase in fuel prices and further environmental regulation had left no choice but to manufacture more fuel efficient and inexpensive vehicles. These heavy demands force researchers to think outside the box. Many innovative research projects came to replace the conventional sheet metal forming of which single point incremental forming is one of them. SPIF is the emerging die-less sheet metal forming process in which the single point tool incrementally forces any single point of sheet metal at any processing time to undergo plastic deformation. It has several advantages over the conventional process like high process flexibility, elimination of die, complex shape and better formability. Previous literature provides enormous research on formability of metal during this process, process with various metals and hybrid metals, the influence of various process parameter, but residual formability after this process is untouched. Thus, the aim of this paper is to investigate the residual formability of the formed parts using single point incremental forming and then restrike with a conventional tool. The common process parameters of single point incremental forming were varied, and residual formability was studied through the conventional process. The strain and thickness distribution were measured and analyzed. In addition, the forming limit of the part was plotted and compared.

Influencing Factors of AZ31B Sheet Deep Drawing

2011 ◽  
Vol 189-193 ◽  
pp. 88-91
Author(s):  
Jun Gao ◽  
Zhen Ming Yue ◽  
Shu Xia Lin
Keyword(s):  
Numerical Simulation ◽  
Deep Drawing ◽  
Experimental Approach ◽  
Elevated Temperatures ◽  
Heating Temperature ◽  
Thickness Distribution ◽  
Simulation Software ◽  
Forming Limit ◽  
Forming Process ◽  
Specific Strength

Magnesium alloys have been attracting much more attentions due to its low density, high specific strength and its lightweight during the past 30 years. In this paper, the deep drawing performance of AZ31B magnisium alloy sheets at elevated temperature was studied by the experimental approach. The results indicated that the formability of the AZ31B sheets at elevated temperatures could be improved significantly. The best external forming parameters can be obtained such as heating temperature of sheet, die-punch clearance, punch fillet radius, etc. Simulating the forming process by using the numerical simulation software, we investigated the stress-strain distribution, thickness distribution and forming limit, etc. The thickness distribution by the numerical simulation agrees well with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document