scholarly journals Buckling and vibration analysis of shape memory laminated composite beams under axially heterogeneous in-plane loads in the glass transition temperature region

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Nilesh Tiwari ◽  
A. A. Shaikh
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Boundary Conditions ◽  
Shape Memory ◽  
Transition Region ◽  
Shape Memory Polymer ◽  
Shear Deformation Theory ◽  
Effect Of Temperature ◽  
Glass Transition Region

AbstractBuckling and vibration study of the shape memory polymer composites (SMPC) across the glass transition temperature under heterogeneous loading conditions are presented. Finite element analysis based on C° continuity equation through the higher order shear deformation theory (HSDT) is employed considering non linear Von Karman approach to estimate critical buckling and vibration for the temperature span from 273 to 373 K. Extensive numerical investigations are presented to understand the effect of temperature, boundary conditions, aspect ratio, fiber orientations, laminate stacking and modes of phenomenon on the buckling and vibration behavior of SMPC beam along with the validation and convergence study. Effect of thermal conditions, particularly in the glass transition region of the shape memory polymer, is considerable and presents cohesive relation between dynamic modulus properties with magnitude of critical buckling and vibration. Moreover, it has also been inferred that type of axial loading condition along with the corresponding boundary conditions significantly affect the buckling and vibration load across the glass transition region.

scholarly journals The Dynamic Constants of Unidirectional Fibrous Composites at the Glass Transition Region as Obtained from the Interphase Concept

2018 ◽  
Author(s):  
Emilio Sideridis ◽  
John Venetis
Keyword(s):  
Composite Material ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Transition Region ◽  
Loss Factor ◽  
Intermediate Phase ◽  
Mechanical Analysis ◽  
Fibrous Composites ◽  
Glass Transition Region

Dynamic mechanical analysis (DMA) is a versatile technique that complements the information given by the more traditional thermal analysis techniques such as differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and thermal mechanical analysis (TMA). Dynamic constants such as storage modulus, loss modulus, and loss factor are temperature dependent and provide information about interfacial bonding between reinforced fibre and polymer matrix of composite material. To study the above mentioned properties at the glass transition region, for unidirectional fibrous composites reinforced with continuous fibers a reliable model was applied. In particular, the composite material was considered as composed of three phases with the intermediate phase between matrix and fibres, the interphase, to have variable properties depending on those of main phases and the mode of preparation of the overall material. The glass transition temperature is defined as the point at which the specific volume versus temperature curve changes abruptly slope marking the region between rubbery polymer and glassy polymer nature. Hence, the behaviour of unidirectional fibrous composites was investigated at this region. Examination of the glass transition temperature, which constitutes an upper limit for the structurally important glassy region through the loss factor, was performed by its consideration as a combination of glass transition temperature of matrix and interphase.

Modification of the Mechanical Behavior in the Glass Transition Region of Poly(lactic acid) (PLA) through Catalyzed Reactive Extrusion with Poly(carbonate) (PC)

2015 ◽  
Vol 1119 ◽  
pp. 292-295
Author(s):  
Vu Thanh Phuong ◽  
Maria Beatrice Coltelli ◽  
Irene Anguillesi ◽  
Patrizia Cinelli ◽  
Andrea Lazzeri
Keyword(s):  
Thermal Stability ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Transition Region ◽  
Reactive Extrusion ◽  
Maximum Temperature ◽  
Glass Transition Region ◽  
The One ◽  
Poly Carbonate

In order to improve the thermal stability of PLA based materials it was followed the strategy of blending it with a polymer having a higher glass transition temperature such as poly (carbonate) of bisphenol A (PC) . PLA/PC blends with different compositions were by melt extrusion produced also in the presence of an interchange reaction catalyst, tetrabutylammonium tetraphenylborate (TBATPB) and triacetin. The dynamical mechanical thermal characterization showed an interesting change of the storage modulus behavior in the PLA glass transition region, evident exclusively in the catalyzed blends. In particular, a new peak in the Tan δ trend at a temperature in between the one of PLA and the one of PC was observed only in the blends obtained in the presence of triacetin and TBATPB. The height and maximum temperature of the peak was different after the annealing of samples at 80°C. The data showed an interesting improvement of thermal stability above the PLA glass transition, this was explained keeping into account the formation of PLA-PC copolymer during the reactive extrusion. Furthermore, the glass transition temperature of the copolymer as a function of composition was studied and the obtained trend was discussed by comparing with literature models developed for copolymers.

Characterizing and Modeling the Free Recovery and Constrained Recovery Behavior of a Polyurethane Shape Memory Polymer

2010 ◽  
Author(s):  
Brent L. Volk ◽  
Dimitris C. Lagoudas ◽  
Duncan J. Maitland
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Shape Memory ◽  
Volume Fraction ◽  
Shape Memory Polymer ◽  
Tensile Tests ◽  
Stress Recovery ◽  
Shear Moduli ◽  
Recovery Experiment

In this work, tensile tests are performed on a polyurethane shape memory polymer for both free recovery (extension recovery at zero load) and constrained recovery (stress recovery at constant extension) conditions. The experimental characterization is conducted on an electromechanical screw driven test frame, and a laser extensometer is used in conjunction with the electromechanical frame to provide a non-contact technique for measuring the deformation of the material. The specimens are deformed, above the glass transition temperature, to 10% extension. The SMP is then cooled, at a constant value of extension, to below the glass transition temperature to ‘lock’ the temporary shape. The extension recovery at zero load as well as the stress recovery at a constant value of extension is measured during the first shape memory cycle as the SMP is heated to above its glass transition temperature. The material is observed to recover 93% of the applied deformation when heated at zero load. In addition, a stress recovery of 1.5 MPa is observed when heated while holding a constant value of deformation (10% extension). After performing the experiments, the Chen and Lagoudas model, implemented in 1-D by Volk, et al., is used to simulate and predict the experimental results. The material properties used in the model — namely the coefficients of thermal expansion, shear moduli, and frozen volume fraction — are calibrated from a single free recovery experiment. The calibrated model is then used to simulate the material response for the free recovery tests as well as predict the response for the constrained recovery condition. The model simulations agree well with the free recovery experimental data but predict a larger compressive stress than what is observed during the constrained recovery experiment.

scholarly journals Advanced Infill Designs for 3D Printed Shape-Memory Components

Micromachines ◽  
2021 ◽  
Vol 12 (10) ◽  
pp. 1225
Author(s):  
Daniel Koske ◽  
Andrea Ehrmann
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Shape Memory ◽  
Fused Deposition Modeling ◽  
Shape Memory Polymer ◽  
The Other ◽  
Poly Lactic Acid ◽  
Fused Deposition ◽  
Other Hand

Poly(lactic acid) (PLA) is one of the most often used polymers in 3D printing based on the fused deposition modeling (FDM) method. On the other hand, PLA is also a shape memory polymer (SMP) with a relatively low glass transition temperature of ~60 °C, depending on the exact material composition. This enables, on the one hand, so-called 4D printing, i.e., printing flat objects which are deformed afterwards by heating them above the glass transition temperature, shaping them and cooling them down in the desired shape. On the other hand, objects from PLA which have been erroneously deformed, e.g., bumpers during an accident, can recover their original shape to a certain amount, depending on the applied temperature, the number of deformation cycles, and especially on the number of broken connections inside the object. Here, we report on an extension of a previous study, investigating optimized infill designs which avoid breaking in 3-point bending tests and thus allow for multiple repeated destruction and recovery cycles with only a small loss in maximum force at a certain deflection.

FLUCTUATION OF INTERNAL FRICTION IN METALLIC GLASSES

2011 ◽  
Vol 1300 ◽  
Author(s):  
Y. Miyauchi ◽  
R. Tamura ◽  
Y. Hiki
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Internal Friction ◽  
Metallic Glass ◽  
Transition Region ◽  
Frequency Spectrum ◽  
Metallic Glasses ◽  
Glass Transition Region ◽  
Characteristic Peak

AbstractInternal friction (IF) of a metallic glass Zr55Cu30Al10Ni5 has been measured near the glass transition temperature Tg (= 666 K). The measurement is performed by using DMA (TA Instrument) apparatus at a frequency of 0.01 Hz for a specimen stabilized by annealing. The specimen is kept at a constant temperature T, and the IF value Q-1 is measured as a function of time t. A fluctuation of Q-1 with time is seen, and the magnitude of the fluctuation, F(t), is derived from the Q-1-vs-t data. F(t) is Fourier transformed to the frequency spectrum F(f). Such experiment and analyses are carried out at various temperatures near Tg. A characteristic peak (f ~ 10-3 Hz) is found in the spectrum F(f) in the glass transition region.

Curved Type Pneumatic Artificial Rubber Muscle Using Shape-Memory Polymer

2012 ◽  
Vol 24 (3) ◽  
pp. 472-479 ◽  
Author(s):  
Kazuto Takashima ◽  
◽  
Toshiro Noritsugu ◽  
Jonathan Rossiter ◽  
Shijie Guo ◽  
...  
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Shape Memory ◽  
External Force ◽  
Shape Memory Polymer ◽  
Fiber Reinforcement ◽  
Artificial Muscle ◽  
Pneumatic Artificial Muscle ◽  
Initial Shape

A novel pneumatic artificial muscle actuator is presented which is based on the design of a conventional curved type pneumatic bellows actuator. By inhibiting the extension of one side with fiber reinforcement, bending motion can be induced when air is supplied to the internal bladder. In this study, we developed a new actuator by replacing the fiber reinforcement with a Shape-Memory Polymer (SMP). The SMP can be deformed above its glass transition temperature (Tg) and maintains a rigid shape after it is cooled below Tg. When next heated above Tg, it returns to its initial shape. When only part of our actuator is warmed above Tg, only that portion of the SMP is soft and can actuate. Therefore, the direction of the motion can be controlled by heating. Moreover, our actuator can be deformed by an external force above Tg and fixed by cooling it below Tg.

Sign in / Sign up

Export Citation Format

Share Document