Adoption of continuous processing technologies: Its strategic importance in standardized industrial product-markets

1992 ◽  
Vol 24 (3) ◽  
pp. 209-224 ◽  
Author(s):  
Steven A. Sinclair ◽  
David H. Cohen
Author(s):  
Attila Farkas ◽  
Brigitta Nagy ◽  
György Marosi

Hyperspectral imaging was applied to provide quantitative spatial information about pharmaceutical samples. The aim was to characterize the distribution of active pharmaceutical ingredient (API) in manufactured samples quantitatively. Two kind of API, imipramine and spironolactone were applied in three conventional and two continuous processing technologies. The homogeneity of distributions of 10% API was determined through Raman maps applying macropixel analysis method. Non-overlapping macropixel analysis (Poole-index) and calculation of distributional homogeneity indices (DHIs) were compared as a measure of homogeneity. Non-overlapping macropixel approach proved to be more sensible than DHI evaluation. For enhancing efficacy of DHI we suggest a correction by weighting scores and considering relative standard deviations. This way the capability of DHI can be improved significantly. The very slight differences between the continuous methods (the homogeneity of which are much higher than that of conventional technologies) could be quantified.


2021 ◽  
Author(s):  
Ajinkya Pandit ◽  
Gavin Walker

Crystallization, filtration and drying are important separation and purification unit operations in the pharmaceutical and speciality chemical industries. Continuous processing technologies have emerged as a promising alternative to the more conventional batch processing. Previous studies primarily focus on crystallization and as a result subsequent stage of filtration and drying are overlooked. In the present short communication, a phenomenological parallel is drawn with the drying of porous solids, studies for which are relatively widely reported. Such analysis helps to identify, the fundamental cause for lump formation, and possible mitigation strategies. Based on the postulated physical scenario, two prototype designs to intensify continuous operation of filtration and drying units are discussed. The prototype solutions could make it possible to intensify or combine multiple stages of filtration, deliquoring, washing and drying thus enabling efficient continuous processing of solid form pharmaceutical and specialty chemicals.


Author(s):  
N. Golub ◽  
M. Potapova ◽  
M. Shinkarchuk ◽  
O. Kozlovets

The paper deals with the waste disposal problem of the alcohol industry caused by the widespread use of alcohol as biofuels. In the technology for the production of alcohol from cereal crops, a distillery spent wash (DSW) is formed (per 1 dm3 of alcohol – 10–20 dm3 DSW), which refers to highly concentrated wastewater, the COD value reaches 40 g O2/dm3. Since the existing physical and chemical methods of its processing are not cost-effective, the researchers develop the processing technologies for its utilization, for example, an anaerobic digestion. Apart from the purification of highly concentrated wastewater, the advantage of this method is the production of biogas and highquality fertilizer. The problems of biotechnology for biogas production from the distillery spent wash are its high acidity–pH 3.7–5.0 (the optimum pH value for the methanogenesis process is 6.8–7.4) and low nitrogen content, the lack of which inhibits the development of the association of microorganisms. In order to solve these problems, additional raw materials of various origins (chemical compounds, spent anaerobic sludge, waste from livestock farms, etc.) are used. The purpose of this work is to determine the appropriate ratio of the fermentable mixture components: cosubstrate, distillery spent wash and wastewater of the plant for co-fermentation to produce an energy carrier (biogas) and effective wastewater treatment of the distillery. In order to ensure the optimal pH for methanogenesis, poultry manure has been used as a co-substrate. The co-fermentation process of DSW with manure has been carried out at dry matter ratios of 1:1, 1:3, 1:5, 1:7 respectively. It is found that when the concentration of manure in the mixture is insufficient (DSW/manure – 1:1, 1:3), the pH value decreases during fermentation which negatively affects methane formation; when the concentration of manure in the mixture is increased (DSW/manure – 1:5, 1:7), the process is characterized by a high yield of biogas and methane content. The maximum output of biogas with a methane concentration of 70 ± 2% is observed at the ratio of components on a dry matter “wastewater: DSW: manure” – 0,2:1:7 respectively. The COD reduction reaches a 70% when using co-fermentation with the combination of components “wastewater: DSW: manure” (0,3:1:5) respectively.


2020 ◽  
Vol 86 (4) ◽  
pp. 61-65
Author(s):  
M. V. Abramchuk ◽  
R. V. Pechenko ◽  
K. A. Nuzhdin ◽  
V. M. Musalimov

A reciprocating friction machine Tribal-T intended for automated quality control of the rubbing surfaces of tribopairs is described. The distinctive feature of the machine consists in implementation of the forced relative motion due to the frictional interaction of the rubbing surfaces fixed on the drive and conjugate platforms. Continuous processing of the signals from displacement sensors is carried out under conditions of continuous recording of mutual displacements of loaded tribopairs using classical approaches of the theory of automatic control to identify the tribological characteristics. The machine provides consistent visual real time monitoring of the parameters. The MATLAB based computer technologies are actively used in data processing. The calculated tribological characteristics of materials, i.e., the dynamic friction coefficient, damping coefficient and measure of the surface roughness, are presented. The tests revealed that a Tribal-T reciprocating friction machine is effective for real-time study of the aforementioned tribological characteristics of materials and can be used for monitoring of the condition of tribo-nodes of machines and mechanisms.


Author(s):  
Luzmila Burbano Mera ◽  
Marcos Dávila Cedeño ◽  
Tatiana Martínez Santana ◽  
Ramón E. Cevallos Cedeño

Abstract:  Manabí and Ecuadorian population in general are consumers of tomato paste in different forms, so that producers and industrial product processing always looking to have a high quality  and  good  prices  for  the  benefit  of its  customers.  This research based on the results obtained, it leaves a number of very valuable conclusions for determining the carrot pulp will have a positive impact on the physical, chemical and organoleptic, when combined with the tomato paste features, without diminishing or provide a look that could adversely affect its commercial presentation to the client. The objective of this research was to get the development of a tomato paste mixed with carrot paste, with the purpose of obtaining an improved nutritional properties (fiber and beta-carotene) for the benefit of the consumer. Index Terms:  Pasta, tomato, carrot, consistency, nutritional properties.


Sign in / Sign up

Export Citation Format

Share Document