Extended model for single-blow transient testing method in evaluating thermal performance of heat transfer surfaces

1994 ◽  
Vol 21 (1) ◽  
pp. 53-63 ◽  
Author(s):  
Chin-Hsiang Cheng ◽  
Chih-Shih Huang
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Extended Model ◽  
Testing Method ◽  
Performance Of Heat Transfer

Effects of Surface Coating of Nanoparticles on Thermal Performance of Open Loop Pulsating Heat Pipes

2012 ◽  
Author(s):  
Mehdi Taslimifar ◽  
Maziar Mohammadi ◽  
Ali Adibnia ◽  
Hossein Afshin ◽  
Mohammad Hassan Saidi ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Surface Coating ◽  
Heat Pipes ◽  
Open Loop ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Performance Of Heat Transfer

Homogenous dispersing of nanoparticles in a base fluid is an excellent way to increase the thermal performance of heat transfer devices especially Heat Pipes (HPs). As a wickless, cheap and efficient heat pipe, Pulsating Heat Pipes (PHPs) are important candidates for thermal application considerations. In the present research an Open Loop Pulsating Heat Pipe (OLPHP) is fabricated and tested experimentally. The effects of working fluid namely, water, Silica Coated ferrofluid (SC ferrofluid), and ferrofluid without surface coating of nanoparticles (ferrofluid), charging ratio, heat input, and application of magnetic field on the overall thermal performance of the OLPHPs are investigated. Experimental results show that ferrofluid has better heat transport capability relative to SC ferrofluid. Furthermore, application of magnetic field improves the heat transfer performance of OLPHPs charged with both ferrofluids.

Experimental study of thermohydraulic characteristics and irreversibility analysis of novel axial corrugated tube with spring tape inserts

2020 ◽  
Vol 92 (3) ◽  
pp. 30901
Author(s):  
Suvanjan Bhattacharyya ◽  
Debraj Sarkar ◽  
Ulavathi Shettar Mahabaleshwar ◽  
Manoj K. Soni ◽  
M. Mohanraj
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Thermal Performance ◽  
Working Fluid ◽  
The Novel ◽  
Heat Exchanger Tube ◽  
Heat Transfer Augmentation ◽  
Corrugated Tube ◽  
The Impact ◽  
Exchanger Tube

The current study experimentally investigates the heat transfer augmentation on the novel axial corrugated heat exchanger tube in which the spring tape is introduced. Air (Pr = 0.707) is used as a working fluid. In order to augment the thermohydraulic performance, a corrugated tube with inserts is offered. The experimental study is further extended by varying the important parameters like spring ratio (y = 1.5, 2.0, 2.5) and Reynolds number (Re = 10 000–52 000). The angular pitch between the two neighboring corrugations and the angle of the corrugation is kept constant through the experiments at β = 1200 and α = 600 respectively, while two different corrugations heights (h) are analyzed. While increasing the corrugation height and decreasing the spring ratio, the impact of the swirling effect improves the thermal performance of the system. The maximum thermal performance is obtained when the corrugation height is h = 0.2 and spring ratio y = 1.5. Eventually, correlations for predicting friction factor (f) and Nusselt number (Nu) are developed.

An Investigation of the Effect of interrupted fin arrangements on the Thermal Performance of a Heat Sink under a Free Convection Condition

2019 ◽  
Vol 7 (1) ◽  
pp. 43-53
Author(s):  
Abbas Jassem Jubear ◽  
Ali Hameed Abd
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Natural Convection ◽  
Thermal Performance ◽  
Heat Sink ◽  
Numerical Study ◽  
Ansys Fluent ◽  
Fluent Software ◽  
Steady State Heat ◽  
Steady State Heat Transfer

The heat sink with vertically rectangular interrupted fins was investigated numerically in a natural convection field, with steady-state heat transfer. A numerical study has been conducted using ANSYS Fluent software (R16.1) in order to develop a 3-D numerical model.  The dimensions of the fins are (305 mm length, 100 mm width, 17 mm height, and 9.5 mm space between fins. The number of fins used on the surface is eight. In this study, the heat input was used as follows: 20, 40, 60, 80, 100, and 120 watts. This study focused on interrupted rectangular fins with a different arrangement and angle of the fins. Results show that the addition of interruption in fins in various arrangements will improve the thermal performance of the heat sink, and through the results, a better interruption rate as an equation can be obtained.

An Experimental and Numerical Study of Heat Transfer and Pressure Loss in a Rectangular Channel With V-Shaped Ribs

2006 ◽  
Author(s):  
Michael Maurer ◽  
Jens von Wolfersdorf ◽  
Michael Gritsch
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Transfer Enhancement ◽  
High Reynolds Numbers ◽  
High Reynolds

An experimental and numerical study was conducted to determine the thermal performance of V-shaped ribs in a rectangular channel with an aspect ratio of 2:1. Local heat transfer coefficients were measured using the steady state thermochromic liquid crystal technique. Periodic pressure losses were obtained with pressure taps along the smooth channel sidewall. Reynolds numbers from 95,000 to 500,000 were investigated with V-shaped ribs located on one side or on both sides of the test channel. The rib height-to-hydraulic diameter ratios (e/Dh) were 0.0625 and 0.02, and the rib pitch-to-height ratio (P/e) was 10. In addition, all test cases were investigated numerically. The commercial software FLUENT™ was used with a two-layer k-ε turbulence model. Numerically and experimentally obtained data were compared. It was determined that the heat transfer enhancement based on the heat transfer of a smooth wall levels off for Reynolds numbers over 200,000. The introduction of a second ribbed sidewall slightly increased the heat transfer enhancement whereas the pressure penalty was approximately doubled. Diminishing the rib height at high Reynolds numbers had the disadvantage of a slightly decreased heat transfer enhancement, but benefits in a significantly reduced pressure loss. At high Reynolds numbers small-scale ribs in a one-sided ribbed channel were shown to have the best thermal performance.

Sign in / Sign up

Export Citation Format

Share Document