Kinetic modelling of geochemical processes at the Aitik mining waste rock site in northern Sweden

1994 ◽  
Vol 9 (5) ◽  
pp. 583-595 ◽  
Author(s):  
Bo Strömberg ◽  
Steven Banwart
2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Saijun Zhou ◽  
Andrew Hursthouse ◽  
Tengshu Chen

Major sources of pollution during the antimony (Sb) mining and processing are mining waste rock, smelting waste, tailings dam, and underground tunnel wastewater. The aim of the present study was to assess magnitude of pollution from Sb mine by taking four types of samples: soil in the mining waste rock zone, soil in the smelting zone, soil in tailings zone, and soil in underground tunnel wastewater zone. Sixty soil samples from the four zones were taken for experimental work, and the contents and morphological characteristics of the six potentially toxic elements (PTEs) such as Sb, As, Hg, Pb, Cd, and Zn in the soil samples were measured by using a hydride generation atomic fluorescence spectrometer (AFS-9700). The results show that the soil of the mine area is seriously polluted. The average contents of Sb, As, Hg, Pb, Cd, and Zn in the soil reach 1267.20 mg·kg−1, 94.44 mg·kg−1, 1.46 mg·kg−1, 184.19 mg·kg−1, 8.54 mg·kg−1, and 1054.11 mg·kg−1, respectively. There exists good correlation between the PTEs in the soil, with Sb strongly positively correlated with As, Hg, Pb, and Zn. The intensity of pollution is highest in the antimony-smelting zone, where the potential ecological risk index is over 15,000, followed by the tailings zone and mining waste rock zone, with the underground tunnel wastewater zone being the lowest. Using sequential chemical extraction, the elements are associated with the residual fraction, followed by organic-sulfide fraction, and smaller portions in the Fe-Mn oxide, carbonate, and exchangeable fractions. There are great differences in the speciation content of different elements in different sampling zones. The study implicates that Sb-smelting zone is the potential source of PTEs and maximum metals are associated with residual phase, out of which significant portion is associated with mobile fraction or phase.


2006 ◽  
Vol 2006 (2) ◽  
pp. 2262-2281 ◽  
Author(s):  
Ken Wangerud ◽  
Roelof Versteeg ◽  
Gail Heath ◽  
Rich Markiewicz ◽  
Alex Richardson

2007 ◽  
Vol 20-21 ◽  
pp. 189-192
Author(s):  
L. Moreno

The release of contaminants from mining wastes containing sulphide minerals is addressed. The paper shows the application of a methodology, Performance Assessment (PA), to the long-term behaviour of waste deposits. The aim of the paper is to address the different processes that occur in deposits for mining waste. These processes are applied to one study case; drainage water from a waste rock dump at the Aitik mine in northern Sweden.


Author(s):  
He Niu ◽  
Lugas Raka Adrianto ◽  
Alexandra Gomez Escobar ◽  
Vladimir Zhukov ◽  
Priyadharshini Perumal ◽  
...  

Abstract Sulfidic mining waste rock is a side stream from the mining industry with a potential environmental burden. Alkali activation is a promising method for transforming mining waste into construction materials. However, the low reactivity of minerals can be a sizeable challenge in alkali activation. In the present study, the reactivity of waste rock was enhanced by mechanochemical treatment with a LiCl-containing grinding aid. X-ray diffraction (XRD) and diffuse reflectance infrared Fourier transform (DRIFT) analysis were utilized to display the structural alteration of individual minerals. A schematic implication of the grinding mechanism of mica was provided according to the results of transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The alkaline solubility displayed the enhanced chemical reactivity of the waste rock, in which Si and Al solubility increased by roughly 10 times and 40 times, respectively. The amorphization of aluminosilicate is achieved through chemical assisted mechanochemical activation. Sulfidic waste rock, as the sole precursor in alkali activation, achieved a 28-day compressive strength exceeding 10 MPa under ambient curing conditions. The simulation of the upscaled grinding process was conducted via the HSC Chemistry® software with a life-cycle assessment. The results showed that mining waste rock can be a promising candidate for geopolymer production with a lower carbon footprint, compared to traditional Portland cement. Graphical Abstract


Sign in / Sign up

Export Citation Format

Share Document