scholarly journals Effects of hole configuration on film cooling effectiveness and particle deposition on curved surfaces in gas turbines

2021 ◽  
Vol 190 ◽  
pp. 116861
Author(s):  
Jin Wang ◽  
Zhanming Zhao ◽  
Liang Tian ◽  
Xiaodong Ren ◽  
Bengt Sundén
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Particle Deposition ◽  
Curved Surfaces ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Hole Configuration

Conjugate Heat Transfer and Film Cooling of a Multi-Stage Cooling Scheme

2008 ◽  
Author(s):  
M. Ghorab ◽  
S. I. Kim ◽  
I. Hassan
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Gas Turbines ◽  
Conjugate Heat Transfer ◽  
Density Ratio ◽  
Design Parameters ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Multi Stage ◽  
Internal Gap

Cooling techniques play a key role in improving efficiency and power output of modern gas turbines. The conjugate technique of film and impingement cooling schemes is considered in this study. The Multi-Stage Cooling Scheme (MSCS) involves coolant passing from inside to outside turbine blade through two stages. The first stage; the coolant passes through first hole to internal gap where the impinging jet cools the external layer of the blade. Finally, the coolant passes through the internal gap to the second hole which has specific designed geometry for external film cooling. The effect of design parameters, such as, offset distance between two-stage holes, gap height, and inclination angle of the first hole, on upstream conjugate heat transfer rate and downstream film cooling effectiveness performance are investigated computationally. An Inconel 617 alloy with variable properties is selected for the solid material. The conjugate heat transfer and film cooling characteristics of MSCS are analyzed across blowing ratios of Br = 1 and 2 for density ratio, 2. This study presents upstream wall temperature distributions due to conjugate heat transfer for different gap design parameters. The maximum film cooling effectiveness with upstream conjugate heat transfer is less than adiabatic film cooling effectiveness by 24–34%. However, the full coverage of cooling effectiveness in spanwise direction can be obtained using internal cooling with conjugate heat transfer, whereas adiabatic film cooling effectiveness has narrow distribution.

scholarly journals A review of multiphase flow and deposition effects in film-cooled gas turbines

2018 ◽  
Vol 22 (5) ◽  
pp. 1905-1921 ◽  
Author(s):  
Jin Wang ◽  
Milan Vujanovic ◽  
Bengt Sunden
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Particle Deposition ◽  
Experimental Studies ◽  
Turbulence Models ◽  
Phase Flow ◽  
Two Phase ◽  
Film Cooling Effectiveness ◽  
Factors Affecting ◽  
Multi Phase Flow

This paper presents a review of particle deposition research in film-cooled gas turbines based on the recent open literature. Factors affecting deposition capture efficiency and film cooling effectiveness are analyzed. Experimental studies are summarized into two discussions in actual and virtual deposition environments. For investigation in virtual deposition environments, available and reasonable results are obtained by comparison of the Stokes numbers. Recent advances in particle deposition modeling for computational fluid dynamics are also reviewed. Various turbulence models for numerical simulations are investigated, and solutions for treatment of the particle sticking probability are described. In addition, analysis of injecting mist into the coolant flow is conducted to investigate gas-liquid two-phase flow in gas turbines. The conclusion remains that considerable re-search is yet necessary to fully understand the roles of both deposition and multi-phase flow in gas turbines.

Implementation of Hole-Pair in Ramp to Improve Film Cooling Effectiveness on a Plain Surface

2020 ◽  
Author(s):  
Sadam Hussain ◽  
Xin Yan
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Density Ratio ◽  
Hole Pair ◽  
Cooling Effect ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cooling Hole ◽  
Plain Surface

Abstract Film cooling is one of the most critical technologies in modern gas turbine engine to protect the high temperature components from erosion. It allows gas turbines to operate above the thermal limits of blade materials by providing the protective cooling film layer on outer surfaces of blade against hot gases. To get a higher film cooling effect on plain surface, current study proposes a novel strategy with the implementation of hole-pair into ramp. To gain the film cooling effectiveness on the plain surface, RANS equations combined with k-ω turbulence model were solved with the commercial CFD solver ANSYS CFX11.0. In the numerical simulations, the density ratio (DR) is fixed at 1.6, and the film cooling effect on plain surface with different configurations (i.e. with only cooling hole, with only ramp, and with hole-pair in ramp) were numerically investigated at three blowing ratios M = 0.25, 0.5, and 0.75. The results show that the configuration with Hole-Pair in Ramp (HPR) upstream the cooling hole has a positive effect on film cooling enhancement on plain surface, especially along the spanwise direction. Compared with the baseline configuration, i.e. plain surface with cylindrical hole, the laterally-averaged film cooling effectiveness on plain surface with HPR is increased by 18%, while the laterally-averaged film cooling effectiveness on plain surface with only ramp is increased by 8% at M = 0.5. As the blowing ratio M increases from 0.25 to 0.75, the laterally-averaged film cooling effectiveness on plain surface with HPR is kept on increasing. At higher blowing ratio M = 0.75, film cooling effectiveness on plain surface with HPR is about 19% higher than the configuration with only ramp.

An Experimental Study of the Leakage Flow Effect on the Film Cooling Effectiveness of a Gas Turbine Shroud

2021 ◽  
pp. 1-18
Author(s):  
Gi Mun Kim ◽  
Soo In Lee ◽  
Jin Young Jeong ◽  
Jae Su Kwak ◽  
Seokbeom Kim ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Density Ratio ◽  
Secondary Flows ◽  
Leakage Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
High Heat Transfer ◽  
Hole Configuration ◽  
Cooling Hole

Abstract In the vicinity of gas turbine blades, a complex flow field is formed due to the flow separation, reattachment, and secondary flows, and this results in a locally non-uniform and high heat transfer on the surfaces. The present study experimentally investigates the effects of leakage flow through the slot between the gas turbine vane and blade rows on the film cooling effectiveness of the forward region of the shroud ring segment. The experiment is carried out in a linear cascade with five blades. Instead of the vane, a row of rods at the location of the vane trailing edge is installed to consider the wake effect. The leakage flow is introduced through the slot between the vane and blade rows, and additional coolant air is injected from the cooling holes installed at the vane's outer zone. The effects of the slot geometry, cooling hole configuration, and blowing ratio on the film cooling effectiveness are experimentally investigated using the pressure sensitive paint (PSP) technique. CO2 gas and a mixture of SF6 and N2 (25%+75%) are used to simulate the leakage flow to the mainstream density ratios of 1.5 and 2.0, respectively. The results indicate that the area averaged film cooling effectiveness is affected more by the slot width than by the cooling hole configuration at the same injection conditions, and the lower density ratio cases show higher film cooling effectiveness than the higher density ratio case at the same cooling configuration.

Effects of Blowing Ratio on Multiple Shallow Angle Film Cooling Holes

2012 ◽  
Vol 225 ◽  
pp. 49-54 ◽  
Author(s):  
Kamil Abdullah ◽  
Ken Ichi Funazaki
Keyword(s):  
Temperature Field ◽  
Surface Temperature ◽  
Film Cooling ◽  
Cooling Effectiveness ◽  
Ir Camera ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Hole Configuration ◽  
The Common ◽  
Film Cooling Holes

This paper presents the investigation on the effects of the blowing ratio of multiple shallow angle film cooling holes. Multiple film cooling holes having a shallow hole angle (θ = 20°), arranged to perform in-line hole configuration has been considered in the present study. The investigation focuses on the effects of high blowing ratio of the film cooling effectiveness which have been carried out at ReD= 3100 and BR = 2.0, 3.0 and 4.0. The experiments make use of the IR camera in capturing the surface temperature to determine the film cooling effectiveness. The contours of the film cooling effectiveness distribution together with plots on laterally average film cooling effectiveness along the x/D are presented. The discussions have been made with a support of the temperature field captured at x/D = 3, 13, 23, and 33. The results clearly show the benefit of the employment of shallow hole angle (θ = 20°) at high blowing ratio which is much more superior in comparison to the common hole configuration (θ = 35°).

Highest-Efficient Film Cooling by Improved NEKOMIMI Film Cooling Holes: Part 1 — Ambient Air Flow Conditions

2013 ◽  
Author(s):  
Karsten Kusterer ◽  
Nurettin Tekin ◽  
Frederieke Reiners ◽  
Dieter Bohn ◽  
Takao Sugimoto ◽  
...  
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Air Flow ◽  
Ambient Air ◽  
Flow Conditions ◽  
Test Rig ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Technology ◽  
Cooling Air

In modern gas turbines, the film cooling technology is essential for the protection of the hot parts, in particular of the first stage vanes and blades of the turbine, against the hot gases from the combustion process in order to reach an acceptable life span of the components. As the cooling air is usually extracted from the compressor, the reduction of the cooling effort would directly result to an increased thermal efficiency of the gas turbine. Understanding of the fundamental physics of film cooling is necessary for the improvement of the state-of-the-art. Thus, huge research efforts by industry as well as research organizations have been undertaken to establish high efficient film cooling technologies. It is a today common knowledge that film cooling effectiveness degradation is caused by secondary flows inside the cooling jets, i.e. the Counter-Rotating Vortices (CRV) or sometimes also mentioned as kidney-vortices, which induce a lift-off of the jet. Further understanding of the secondary flow development inside the jet and how this could be influenced, has led to hole configurations, which can induce Anti-Counter-Rotating Vortices (ACRV) in the cooling jets. As a result, the cooling air remains close to the wall and is additionally distributed flatly along the surface. Beside different other technologies, the NEKOMIMI cooling technology is a promising approach to establish the desired ACRV. It consists of a combination of two holes in just one configuration so that the air is distributed mainly on two cooling air streaks following the special shape of the generated geometry. The original configuration was found to be difficult for manufacturing even by advanced manufacturing processes. Thus, the improvement of this configuration has been reached by a set of geometry parameters, which lead to configurations much easier to be manufactured but preserving the principle of the NEKOMIMI technology. Within a numerical parametric study several advanced configurations have been obtained and investigated under ambient air flow conditions similar to conditions for a wind tunnel test rig. By systematic variation of the parameters a further optimization with respect to highest film cooling effectiveness has been performed. A set of most promising configurations has been also investigated experimentally in the test rig. The best configuration outperforms the basic configuration by 17% regarding the overall averaged adiabatic film cooling effectiveness under the experimental conditions.

Double-Jet Ejection of Cooling Air for Improved Film-Cooling

2006 ◽  
Author(s):  
Karsten Kusterer ◽  
Dieter Bohn ◽  
Takao Sugimoto ◽  
Ryozo Tanaka
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Gas Flow ◽  
Operating Conditions ◽  
Cooling Effectiveness ◽  
Equal Distribution ◽  
Cooling Fluid ◽  
Film Cooling Effectiveness ◽  
Conventional Film ◽  
Cooling Technology

Film-cooling in gas turbines leads to aerodynamic mixing losses and reduced temperatures of the gas flow. Improvements of the gas turbine thermal efficiency can be achieved by reducing the cooling fluid amount and by establishing a more equal distribution of the cooling fluid along the surface. It is well known that vortex systems in the cooling jets are the origin of reduced film-cooling effectiveness. For the streamwise ejection case, kidney-vortices result in a lift-off of the cooling jets; for the lateral ejection case, usually only one dominating vortex remains, leading to hot gas flow underneath the jet from one side. Based on the results of numerical analyses, a new cooling technology has been introduced by the authors, which reaches high film-cooling effectiveness as a result of a well-designed cooling hole arrangement for interaction of two neighbouring cooling jets (Double-jet Film-cooling DJFC). The results show that configurations exist, where an improved film-cooling effectiveness can be reached because an anti-kidney vortex pair is established in the double-jet. The paper aims on following major contributions: • to introduce the Double-jet Film-cooling (DJFC) as an alternative film-cooling technology to conventional film-cooling design. • to explain the major phenomena, which lead to the improvement of the film-cooling effectiveness by application of the DJFC. • to prove basic applicability of the DJFC to a realistic blade cooling configuration and present first test results under machine operating conditions.

scholarly journals Computational Analysis of Surface Curvature Effect on Mist Film-Cooling Performance

2008 ◽  
Vol 130 (12) ◽  
Author(s):  
Xianchang Li ◽  
Ting Wang
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Leading Edge ◽  
Operating Conditions ◽  
Curved Surfaces ◽  
Curvature Effect ◽  
Water Droplets ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Air Film

Air-film cooling has been widely employed to cool gas turbine hot components, such as combustor liners, combustor transition pieces, turbine vanes, and blades. Studies with flat surfaces show that significant enhancement of air-film cooling can be achieved by injecting water droplets with diameters of 5–10 μm into the coolant airflow. The mist/air-film cooling on curved surfaces needs to be studied further. Numerical simulation is adopted to investigate the curvature effect on mist/air-film cooling, specifically the film cooling near the leading edge and on the curved surfaces. Water droplets are injected as dispersed phase into the coolant air and thus exchange mass, momentum, and energy with the airflow. Simulations are conducted for both 2D and 3D settings at low laboratory and high operating conditions. With a nominal blowing ratio of 1.33, air-only adiabatic film-cooling effectiveness on the curved surface is lower than on a flat surface. The concave (pressure) surface has a better cooling effectiveness than the convex (suction) surface, and the leading-edge film cooling has the lowest performance due to the main flow impinging against the coolant injection. By adding 2% (weight) mist, film-cooling effectiveness can be enhanced approximately 40% at the leading edge, 60% on the concave surface, and 30% on the convex surface. The leading edge film cooling can be significantly affected by changing of the incident angle due to startup or part-load operation. The film cooling coverage could switch from the suction side to the pressure side and leave the surface of the other part unprotected by the cooling film. Under real gas turbine operating conditions at high temperature, pressure, and velocity, mist-cooling enhancement could reach up to 20% and provide a wall cooling of approximately 180 K.

scholarly journals Heat transfer and film cooling measurements on aerodynamic geometries relevant for turbomachinery

2021 ◽  
Vol 3 (12) ◽  
Author(s):  
Patrick Jagerhofer ◽  
Jakob Woisetschläger ◽  
Gerhard Erlacher ◽  
Emil Göttlich
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Measurement Technique ◽  
Film Cooling ◽  
Curved Surfaces ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Horseshoe Vortices

Abstract A measurement technique for recording convective heat transfer coefficient and adiabatic film cooling effectiveness in demanding environments with highly curved surfaces and limited optical access, such as turbomachinery, is presented. Thermography and tailor-made flexible heating foils are used in conjunction with a novel multistep calibration and data reduction method. This method compensates for sensor drift, angle dependence of surface emissivity and window transmissivity, heat flux inhomogeneity, and conductive losses. The 2D infrared images are mapped onto the 3D curved surfaces and overlapped, creating surface maps of heat transfer coefficient and film cooling effectiveness covering areas significantly larger than the window size. The measurement technique’s capability is demonstrated in a sector-cascade test rig of a turbine center frame (TCF), an inherent component of modern two-spool turbofan engines. The horseshoe vortices were found to play a major role for the thermal integrity of turbine center frames, as they lead to a local increase in heat transfer, and at the same instance, to a reduction of film cooling effectiveness. It was also found that the horseshoe vortices lift off from the curved surface at 50% hub length, resulting in a pair of counter-rotating vortices. The measurement technique was validated by comparing the data against flat plate correlations and also by the linear relation between temperature difference and heat flux. This study is complemented with an extensive error and uncertainty analysis. Article highlights This paper presents an accurate measurement technique for heat transfer and film cooling on 3D curved surfaces with limited optical access using flexible tailor-made heating foils, infrared thermography and a high-fidelity multistep calibration process. Graphical abstract

Double-Jet Film-Cooling for Highly Efficient Film-Cooling With Low Blowing Ratios

2008 ◽  
Author(s):  
Karsten Kusterer ◽  
Anas Elyas ◽  
Dieter Bohn ◽  
Takao Sugimoto ◽  
Ryozo Tanaka
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Original Design ◽  
Long Distance ◽  
Mixing Processes ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Air ◽  
Very High

Further improvement of the thermal efficiency of modern gas turbines can be achieved by a further reduction of the cooling air amount. Therefore, it is necessary to increase the cooling effectiveness so that the available cooling air fulfils the cooling task even if the amount has been reduced. In particular, the cooling effort for the vanes and blades of the first stage in a modern gas turbine is very high. The task of the film-cooling is to protect the blade material from the hot gas attack to the surface. Unfortunately, aerodynamic mixing processes are enhanced by secondary vortices in the cooling jets and, thus, the film-cooling effectiveness is reduced shortly behind the cooling air ejection through the holes. By improvement of the hole positioning the negative interaction effects can be reduced. The Double-jet Film-cooling (DJFC) Technology invented by the authors is one method to reach a significant increase in film-cooling effectiveness by establishing an anti-kidney vortex pair in a combined jet from the two jets starting from cylindrical ejection holes. This has been shown by numerical investigations and application to an industrial gas turbine as reported in recent publications. Whereas the original design application has been for moderate and high blowing ratios, the present numerical investigation shows that the DJFC is also applicable for lower blowing ratios (0.5<M<1.0) with only slight modification of the geometry of the configuration. The anti-kidney vortex concept can also be established for the lower blowing ratios and, as a result, a very high film-cooling effectiveness is reached not only behind the ejection holes but also for a very long distance downstream (> 30 hole diameters).

Sign in / Sign up

Export Citation Format

Share Document