A novel approach for the strain rate dependent modelling of woven composites

2018 ◽  
Vol 192 ◽  
pp. 568-576 ◽  
Author(s):  
N. Feld ◽  
F. Coussa ◽  
B. Delattre
Keyword(s):  
Strain Rate ◽  
Woven Composites ◽  
Rate Dependent ◽  
Novel Approach

Modelling the in-plane strain rate dependent behaviour of woven composites with special emphasis on the non-linear shear response

2019 ◽  
Vol 210 ◽  
pp. 840-857 ◽  
Author(s):  
F. Martínez-Hergueta ◽  
D. Ares ◽  
A. Ridruejo ◽  
J. Wiegand ◽  
N. Petrinic
Keyword(s):  
Strain Rate ◽  
Plane Strain ◽  
Woven Composites ◽  
Shear Response ◽  
Rate Dependent ◽  
Non Linear ◽  
Linear Shear ◽  
Dependent Behaviour

scholarly journals A Strain Rate Dependent Progressive Damage Model for Carbon Fiber Woven Composites under Low Velocity Impact

2021 ◽  
Vol 2101 (1) ◽  
pp. 012073
Author(s):  
Xueyao Hu ◽  
Jiaojiao Tang ◽  
Wei Xiao ◽  
Kepeng Qu
Keyword(s):  
Strain Rate ◽  
Damage Model ◽  
Low Velocity Impact ◽  
Woven Composites ◽  
Progressive Damage ◽  
Low Velocity ◽  
Velocity Impact ◽  
Rate Dependent ◽  
Plane Direction ◽  
Progressive Damage Model

Abstract A progressive damage model was presented for carbon fiber woven composites under low velocity impact, considering the strain rate sensitivity of both mechanical properties and failure mechanisms. In this model, strain rate dependency of elastic modulus and nominal strength along in-plane direction are considered. Based on the Weibull distribution, stiffness progressive degradation is conducted by introducing strain rate dependent damage variables for distinct damage modes. With the model implemented in ABAQUS/Explicit via user-defined material subroutine (VUMAT), the mechanical behavior and possible damage modes of composites along in-plane direction can be determined. Furthermore, a bilinear traction separation model and a quadratic stress criterion are applied to predict the initiation and evolution of interlaminar delamination. Comparisons are made between the experimental results and numerical simulations. It is shown that the mechanical response and damage characteristics under low velocity impact, such as contact force history and delamination, are more consistent with the experimental results when taken the strain rate effect into consideration.

Strain-rate dependent material properties of selective laser melted AlSi10Mg and AlSi3.5Mg2.5

2020 ◽  
Vol 62 (6) ◽  
pp. 573-583
Author(s):  
Andreas Lutz ◽  
Lukas Huber ◽  
Claus Emmelmann
Keyword(s):  
Strain Rate ◽  
Material Properties ◽  
Rate Dependent

Strain-Rate Dependent Deformation Behavior in WC-10 wt%Ni 3Al Cermet Micropillars Under Uniaxial Compression

2019 ◽  
Author(s):  
Minai Zhang ◽  
Xin Wang ◽  
Alexander D. Dupuy ◽  
Julie M. Schoenung ◽  
Xiaoqiang Li
Keyword(s):  
Strain Rate ◽  
Uniaxial Compression ◽  
Deformation Behavior ◽  
Rate Dependent

scholarly journals Identification of the LLDPE Constitutive Material Model for Energy Absorption in Impact Applications

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1537
Author(s):  
Luděk Hynčík ◽  
Petra Kochová ◽  
Jan Špička ◽  
Tomasz Bońkowski ◽  
Robert Cimrman ◽  
...  
Keyword(s):  
Strain Rate ◽  
Material Model ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Stress Strain ◽  
Rate Dependent ◽  
Constitutive Material Model ◽  
Principal Directions ◽  
Constitutive Material

Current industrial trends bring new challenges in energy absorbing systems. Polymer materials as the traditional packaging materials seem to be promising due to their low weight, structure, and production price. Based on the review, the linear low-density polyethylene (LLDPE) material was identified as the most promising material for absorbing impact energy. The current paper addresses the identification of the material parameters and the development of a constitutive material model to be used in future designs by virtual prototyping. The paper deals with the experimental measurement of the stress-strain relations of linear low-density polyethylene under static and dynamic loading. The quasi-static measurement was realized in two perpendicular principal directions and was supplemented by a test measurement in the 45° direction, i.e., exactly between the principal directions. The quasi-static stress-strain curves were analyzed as an initial step for dynamic strain rate-dependent material behavior. The dynamic response was tested in a drop tower using a spherical impactor hitting a flat material multi-layered specimen at two different energy levels. The strain rate-dependent material model was identified by optimizing the static material response obtained in the dynamic experiments. The material model was validated by the virtual reconstruction of the experiments and by comparing the numerical results to the experimental ones.

A Modified Peric Model for Al-Mg Alloy Sheet with Rate-Independent Initial Yield Stress at Warm Temperatures

2019 ◽  
Vol 287 ◽  
pp. 3-7
Author(s):  
Yong Zhang ◽  
Qing Zhang ◽  
Yuan Tao Sun ◽  
Xian Rong Qin
Keyword(s):  
Flow Stress ◽  
Plastic Strain ◽  
Strain Rate ◽  
Yield Stress ◽  
Constitutive Models ◽  
Mg Alloy ◽  
Initial Yield Stress ◽  
Initial Yield ◽  
Rate Dependent ◽  
Dependent Flow

The constitutive modeling of aluminum alloy under warm forming conditions generally considers the influence of temperature and strain rate. It has been shown by published flow stress curves of Al-Mg alloy that there is nearly no effect of strain rate on initial yield stress at various temperatures. However, most constitutive models ignored this phenomenon and may lead to inaccurate description. In order to capture the rate-independent initial yield stress, Peric model is modified via introducing plastic strain to multiply the strain rate, for eliminating the effect of strain rate when the plastic strain is zero. Other constitutive models including the Wagoner, modified Hockett–Sherby and Peric are also considered and compared. The results show that the modified Peric model could not only describe the temperature-and rate-dependent flow stress, but also capture the rate-independent initial yield stress, while the Wagoner, modified Hockett–Sherby and Peric model can only describe the temperature-and rate-dependent flow stress. Moreover, the modified Peric model could obtain proper static yield stress more naturally, and this property may have potential applications in rate-dependent simulations.

Sign in / Sign up

Export Citation Format

Share Document