A JIT part supply scheduling strategy with electric transport device between central receiving store and supermarkets in the automobile industry considering energy

2021 ◽  
pp. 100126
Author(s):  
Wenrui Jin ◽  
Zhaoxu He ◽  
Tao Peng
Keyword(s):  
Automobile Industry ◽  
Electric Transport ◽  
Scheduling Strategy ◽  
Transport Device

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Research on Development Strategy for China’s Powerful Automobile Industry

2018 ◽  
Vol 20 (1) ◽  
pp. 37
Author(s):  
Yang Dong ◽  
Yanhua Xu ◽  
Tianshu Pang ◽  
Peng Zou
Keyword(s):  
Development Strategy ◽  
Automobile Industry

Financial Performance of Automobile Industry in India

2012 ◽  
Vol 3 (1) ◽  
pp. 67-68
Author(s):  
P. Sankaran P. Sankaran ◽  
◽  
Dr. C. Gounasegaran Dr. C. Gounasegaran ◽  
Dr. R. Azhagaiah Dr. R. Azhagaiah
Keyword(s):  
Financial Performance ◽  
Automobile Industry

A Comparison of Two Sub-structuring Techniques for Representing the Modal Properties of Tires

2001 ◽  
Vol 29 (1) ◽  
pp. 23-43 ◽  
Author(s):  
D. Tsihlas ◽  
T. Lacroix ◽  
B. Clayton
Keyword(s):  
Automobile Industry ◽  
Dynamic Models ◽  
Transfer Functions ◽  
Component Mode Synthesis ◽  
Numerical Techniques ◽  
The Past ◽  
Custom Made ◽  
Modal Behavior ◽  
Noise Vibration ◽  
Reduced Dynamic

Abstract Different numerical sub-structuring techniques for the representation of tire modal behavior have been developed in the past 20 years. By using these numerical techniques reduced dynamic models are obtained which can not only be used for internal studies but also be provided to the automobile industry and linked to reduced dynamic vehicle models in order to optimize the coupled vehicle-tire response for noise vibration and harshness purposes. Two techniques that have been developed in a custom-made finite element code are presented: 1) the component mode synthesis type models for which the wheel center interface is free and 2) the Craig and Bampton type models for which the wheel center interface is fixed. For both techniques the interface between the tire and the ground is fixed. The choice of fixed or free wheel center boundary condition is arbitrary. In this paper we will compare the formulation of these two numerical methods, and we will show the equivalency of both methods by showing the results obtained in terms of frequency and transfer functions. We will show that the two methods are equivalent in principle and the reduced dynamic models can be converted from one to the other. The advantages-disadvantages of each method will be discussed along with a comparison with experimentally obtained results.

Sign in / Sign up

Export Citation Format

Share Document