Transient hot strip measures thermal conductivity of organic foam thermal insulation materials

2018 ◽  
Vol 91 ◽  
pp. 443-450 ◽  
Author(s):  
Rixing Hu ◽  
Aichun Ma ◽  
Yang Li
2014 ◽  
Vol 604 ◽  
pp. 285-288 ◽  
Author(s):  
Saulius Vaitkus ◽  
Rūta Karpavičiūtė ◽  
Sigitas Vėjelis ◽  
Lina Lekūnaitė

Natural fibres from flax and hemp are used as raw materials for efficient thermal insulation. In current work, tests were carried out using chopped and combed long flax fibres as well as chopped and combed long hemp fibres. Investigations have shown that thermal conductivity of natural fibres depends on their preparation method (combing, chopping) and materials density.


Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5616
Author(s):  
Katarzyna Uram ◽  
Maria Kurańska ◽  
Jacek Andrzejewski ◽  
Aleksander Prociak

This paper presents results of research on the preparation of biochar-modified rigid polyurethane foams that could be successfully used as thermal insulation materials. The biochar was introduced into polyurethane systems in an amount of up to 20 wt.%. As a result, foam cells became elongated in the direction of foam growth and their cross-sectional areas decreased. The filler-containing systems exhibited a reduction in their apparent densities of up to 20% compared to the unfilled system while maintaining a thermal conductivity of 25 mW/m·K. Biochar in rigid polyurethane foams improved their dimensional and thermal stability.


2013 ◽  
Vol 1558 ◽  
Author(s):  
Qing Hao ◽  
Minqing Li ◽  
Garrett Joseph Coleman ◽  
Qiang Li ◽  
Pierre Lucas

ABSTRACTWith extremely disordered atomic structures, a glass possesses a thermal conductivity k that approaches the theoretical minimum of its composition, known as the Einstein’s limit.1 Depending on the material composition and the extent of disorder, the thermal conductivity of some glasses can be down to 0.1-0.3 W/m∙K at room temperature,2,3 representing some of the lowest k values among existing solids. Such a low k can be further reduced by the interfacial phonon scattering within a nanocomposite that can be used for thermal insulation applications. In this work, nanocomposites hot pressed from the mixture of glass nanopowder (GeSe4 or Ge20Te70Se10) and commercial SiO2 nanoparticles, or pure glass nanopowder, are investigated for the potential k reduction. It is found that adding SiO2 nanoparticles will instead increase k if the measured k values for usually porous nanocomposites are converted into those for the corresponding solid (kSolid) with Eucken’s formula. In contrast, pure glass nano-samples always show kSolid data significantly reduced from that for the starting glass. For a pure GeSe4 nano-sample, kSolid would beat the Einstein’s limit for its composition.


2020 ◽  
Vol 62 (4) ◽  
pp. 408-412
Author(s):  
Yuksel Palaci

Abstract In this study, the variation of thermal conductivity and density of 15 wt.-% boric acid - 85 wt.-% sepiolite, 30 wt.-% boric acid - 30 wt.-% sepiolite - 40 wt.-% perlite, 30 wt.-% boric acid - 30 wt.-% cordierite - 40 wt.-% perlite and 30 wt.-% boric acid - 30 wt.-% alumina - 40 wt.-% perlite compositions at 700 °C and 900 °C sintering temperatures were investigated. The results show that increasing the amount of boric acid and decreasing the sintering temperature lead to an improvement in thermal insulation properties. There is a direct relation between the thermal conductivity and density of the specimens. Both physical properties change with a change in the sintering temperature and the composition characteristics. Minimum thermal conductivity has been observed in a specimen consisting of 30 wt.-% boric acid - 30 wt.-% alumina - 40 wt.-% perlite.


2006 ◽  
Vol 27 (6) ◽  
pp. 1816-1825 ◽  
Author(s):  
M. Gustavsson ◽  
H. Wang ◽  
R. M. Trejo ◽  
E. Lara-Curzio ◽  
R. B. Dinwiddie ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document