Thermal behaviour of the flow boiling of a complex nanofluid in a rectangular channel: An experimental and numerical study

2020 ◽  
Vol 117 ◽  
pp. 104773
Author(s):  
Hayder I. Mohammed ◽  
Donald Giddings ◽  
Gavin S. Walker ◽  
Pouyan Talebizadehsardari ◽  
Jasim M. Mahdi
Keyword(s):  
Thermal Behaviour ◽  
Numerical Study ◽  
Flow Boiling ◽  
Rectangular Channel

An Experimental and Numerical Study of Heat Transfer and Pressure Loss in a Rectangular Channel With V-Shaped Ribs

2006 ◽  
Author(s):  
Michael Maurer ◽  
Jens von Wolfersdorf ◽  
Michael Gritsch
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Transfer Enhancement ◽  
High Reynolds Numbers ◽  
High Reynolds

An experimental and numerical study was conducted to determine the thermal performance of V-shaped ribs in a rectangular channel with an aspect ratio of 2:1. Local heat transfer coefficients were measured using the steady state thermochromic liquid crystal technique. Periodic pressure losses were obtained with pressure taps along the smooth channel sidewall. Reynolds numbers from 95,000 to 500,000 were investigated with V-shaped ribs located on one side or on both sides of the test channel. The rib height-to-hydraulic diameter ratios (e/Dh) were 0.0625 and 0.02, and the rib pitch-to-height ratio (P/e) was 10. In addition, all test cases were investigated numerically. The commercial software FLUENT™ was used with a two-layer k-ε turbulence model. Numerically and experimentally obtained data were compared. It was determined that the heat transfer enhancement based on the heat transfer of a smooth wall levels off for Reynolds numbers over 200,000. The introduction of a second ribbed sidewall slightly increased the heat transfer enhancement whereas the pressure penalty was approximately doubled. Diminishing the rib height at high Reynolds numbers had the disadvantage of a slightly decreased heat transfer enhancement, but benefits in a significantly reduced pressure loss. At high Reynolds numbers small-scale ribs in a one-sided ribbed channel were shown to have the best thermal performance.

scholarly journals Flow Pattern Map of Flow Boiling in a Rectangular Channel Filled with Porous Media

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2440
Author(s):  
Youngwoo Kim ◽  
Dae Yeon Kim ◽  
Kyung Chun Kim
Keyword(s):  
Porous Media ◽  
Flow Pattern ◽  
Flow Regime ◽  
Annular Flow ◽  
Flow Boiling ◽  
Rectangular Channel ◽  
Flow Patterns ◽  
Flow Pattern Map ◽  
Mist Flow ◽  
Churn Flow

A flow visualization study was carried out for flow boiling in a rectangular channel filled with and without metallic random porous media. Four main flow patterns are observed as intermittent slug-churn flow, churn-annular flow, annular-mist flow, and mist flow regimes. These flow patterns are clearly classified based on the high-speed images of the channel flow. The results of the flow pattern map according to the mass flow rate were presented using saturation temperatures and the materials of porous media as variables. As the saturation temperatures increased, the annular-mist flow regime occupied a larger area than the lower saturation temperatures condition. Therefore, the churn flow regime is narrower, and the slug flow more quickly turns to annular flow with the increasing vapor quality. The pattern map is not significantly affected by the materials of porous media.

Numerical Study of the Effect of Inlet Constriction on Bubble Growth During Flow Boiling in Microchannels

2005 ◽  
Author(s):  
Abhijit Mukherjee ◽  
Satish G. Kandlikar
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Flow Boiling ◽  
Navier Stokes ◽  
Channel Cross Section ◽  
Vapor Bubbles ◽  
Reversed Flow ◽  
Cross Sectional ◽  
Parallel Microchannels ◽  
Energy Equations

Flow boiling through microchannels is characterized by nucleation of vapor bubbles on the channel walls and their rapid growth as they fill the entire channel cross-section. In parallel microchannels connected through a common header, formation of vapor bubbles often results in flow maldistribution that leads to reversed flow in certain channels. The reversed flow is detrimental to the heat transfer and leads to early CHF condition. One way of eliminating the reversed flow is to incorporate flow restrictions at the channel inlet. In the present numerical study, a nucleating vapor bubble placed near the restricted end of a microchannel is numerically simulated. The complete Navier-Stokes equations along with continuity and energy equations are solved using the SIMPLER method. The liquid-vapor interface is captured using the level set technique. The results show that with no restriction the bubble moves towards the nearest channel outlet, whereas in the presence of a restriction, the bubble moves towards the distant but unrestricted end. It is proposed that channels with increasing cross-sectional area may be used to promote unidirectional growth of the vapor plugs and prevent reversed flow.

Performance of rectangular labyrinth weir- an experimental and numerical study

2022 ◽  
Author(s):  
Mosbah Ben Said ◽  
Ahmed Ouamane
Keyword(s):  
Discharge Capacity ◽  
Numerical Study ◽  
Flow Behavior ◽  
Rectangular Channel ◽  
Experimental Models ◽  
Absolute Relative Error ◽  
Labyrinth Weir ◽  
Specific Discharge ◽  
Labyrinth Weirs ◽  
Good Agreement

Abstract Labyrinth weirs are commonly used to increase the capacity of existing spillways and provide more efficient spillways for new dams due to their high specific discharge capacity compared to the linear weir. In the present study, experimental and numerical investigation was conducted to improve the rectangular labyrinth weir performance. In this context, four configurations were tested to evaluate the influence of the entrance shape and alveoli width on its discharge capacity. The experimental models, three models of rectangular labyrinth weir with rounded entrance and one with flat entrance, were tested in rectangular channel conditions for inlet width to outlet width ratios (a/b) equal to 0.67, 1 and 1.5. The results indicate that the rounded entrance increases the weir efficiency by up to 5%. A ratio a/b equal to 1.5 leads to an 8 and 18% increase in the discharge capacity compared to a/b ratio equal to 1 and 0.67, respectively. In addition, a numerical simulation was conducted using the opensource CFD OpenFOAM to analyze and provide more information about the flow behavior over the tested models. A comparison between the experimental and numerical discharge coefficient was performed and good agreement was found (Mean Absolute Relative Error of 4–6%).

Sign in / Sign up

Export Citation Format

Share Document