Quantifying deep cryogenic treatment extent and its effect on steel properties

2021 ◽  
Vol 167 ◽  
pp. 103521
Author(s):  
Paul A. Funk ◽  
Ahmed Kanaan ◽  
Christine Shank ◽  
Peter Cooke ◽  
Igor Sevostianov ◽  
...  
Keyword(s):  
Cryogenic Treatment ◽  
Deep Cryogenic Treatment ◽  
Steel Properties

Effect of Deep-Cryogenic Treatment on High Speed Steel Properties

2009 ◽  
Vol 24 (7-8) ◽  
pp. 743-746 ◽  
Author(s):  
Franjo Cajner ◽  
Vojteh Leskovšek ◽  
Darko Landek ◽  
Hrvoje Cajner
Keyword(s):  
High Speed ◽  
Cryogenic Treatment ◽  
High Speed Steel ◽  
Deep Cryogenic Treatment ◽  
Steel Properties

scholarly journals Effect of deep cryogenic treatment on surface chemistry and microstructure of selected high-speed steels

2021 ◽  
Vol 548 ◽  
pp. 149257
Author(s):  
Patricia Jovičević-Klug ◽  
Monika Jenko ◽  
Matic Jovičević-Klug ◽  
Barbara Šetina Batič ◽  
Janez Kovač ◽  
...  
Keyword(s):  
Surface Chemistry ◽  
High Speed ◽  
Cryogenic Treatment ◽  
Deep Cryogenic Treatment

Effects of deep cryogenic treatment on machinability, hardness and microstructure in dry turning process of tempered steels

2020 ◽  
pp. 095440892097944
Author(s):  
Menderes Kam
Keyword(s):  
Cryogenic Treatment ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Point Of View ◽  
Turning Process ◽  
Deep Cryogenic Treatment ◽  
Dry Turning ◽  
Control Factors ◽  
Heat Treated ◽  
Hardness Values

This study investigated the effects of Deep Cryogenic Treatment (DCT) on machinability, hardness, and microstructure in dry turning process of AISI 4140 (48-51 HRc) tempered steels with ceramic cutting tools on the surface roughness (Ra). DCT process of steels has shown significant improvement in their mechanical properties. In this context, experiments were made with Taguchi L16 method and optimum values were determined. Three different values for each control factors as: different heat treated samples, cutting speeds (160, 200, 240, 280 m/min), feed rates (0.08, 0.12, 0.16, 0.20 mm/rev) were selected. As a result, the lowest Ra value was found to be 0.159 µm for the DCTT36 sample at a cutting speed of 240 m/min, a feed rate of 0.08 mm/rev. The optimum Ra value was the lowest for the DCTT36 sample compared to the other samples as 0.206 µm. The hardness values of the micro and macro were highest for the DCTT36 sample. Microstructural point of view Scanning Electron Microscopy (SEM) point of view, the DCCT36 sample showed that best results owing to its homogeneity. It was concluded that lower Ra values can be obtained with ceramic cutting tool in dry turning experiments according to the studies in the literature review. It is thought to be preferred as an alternative to cylindrical grinding process due to lower cost.

scholarly journals Effect of Deep Cryogenic Treatment on Corrosion Properties of Various High-Speed Steels

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 14
Author(s):  
Jure Voglar ◽  
Živa Novak ◽  
Patricia Jovičević-Klug ◽  
Bojan Podgornik ◽  
Tadeja Kosec
Keyword(s):  
High Speed ◽  
Cryogenic Treatment ◽  
Test Procedure ◽  
High Speed Steel ◽  
High Hardness ◽  
Polarization Measurement ◽  
Deep Cryogenic Treatment ◽  
Corrosion Properties ◽  
Potential Measurement ◽  
Corrosion Studies

The aim of the study was to evaluate the corrosion properties of three different grades of high-speed steel following a heat treatment procedure involving deep cryogenic treatment after quenching and to investigate how these properties are connected to the microstructure and hardness of the material. The hardness of steels was measured, and microstructural properties were determined through observation of the metallographically prepared steels using scanning electron microscopy. These studies were complemented corrosion evaluation by the use of corrosion potential measurement and linear polarization measurement of steels in a sodium tetraborate buffer at pH 10. The results showed that the deep cryogenic procedure of high-speed steel changed the microstructure and consequently affected the hardness of the investigated steels to different extents, depending on their chemical composition. Corrosion studies have confirmed that some high-speed steels have improved corrosion properties after deep cryogenic treatment. The most important improvement in corrosion resistance was observed for deep cryogenically treated high-speed steel EN 1.3395 (M3:2) by 31% when hardened to high hardness values and by 116% under lower hardness conditions. The test procedure for differentiating corrosion properties of differently heat-treated tool steels was established alongside the investigation.

Sign in / Sign up

Export Citation Format

Share Document