LES study on the influence of the diffuser inlet angle of a centrifugal pump on pressure fluctuations

2021 ◽  
Vol 89 ◽  
pp. 108804
Author(s):  
Antonio Posa
Keyword(s):  
Centrifugal Pump ◽  
Pressure Fluctuations ◽  
Inlet Angle

The Effect of the Operating Point on the Pressure Fluctuations at the Blade Passage Frequency in the Volute of a Centrifugal Pump

2002 ◽  
Vol 124 (3) ◽  
pp. 784-790 ◽  
Author(s):  
Jorge L. Parrondo-Gayo ◽  
Jose´ Gonza´lez-Pe´rez ◽  
Joaquı´n Ferna´ndez-Francos
Keyword(s):  
Centrifugal Pump ◽  
Pressure Fluctuations ◽  
Fast Response ◽  
Strong Increase ◽  
Flow Rates ◽  
Blade Passage ◽  
Pressure Transducers ◽  
Leading Role ◽  
Dynamic Forces ◽  
Response Pressure

An experimental investigation is presented which analyzes the unsteady pressure distribution existing in the volute of a conventional centrifugal pump with a nondimensional specific speed of 0.48, for flow-rates from 0% to 160% of the best-efficiency point. For that purpose, pressure signals were obtained at 36 different locations along the volute casing by means of fast-response pressure transducers. Particular attention was paid to the pressure fluctuations at the blade passage frequency, regarding both amplitude and phase delay relative to the motion of the blades. Also, the experimental data obtained was used to adjust the parameters of a simple acoustic model for the volute of the pump. The results clearly show the leading role played by the tongue in the impeller-volute interaction and the strong increase in the magnitude of dynamic forces and dipole-like sound generation in off-design conditions.

Relationship Between Unsteady Flow, Pressure Fluctuations, and Noise in a Centrifugal Pump—Part B: Effects of Blade-Tongue Interactions

1995 ◽  
Vol 117 (1) ◽  
pp. 30-35 ◽  
Author(s):  
S. Chu ◽  
R. Dong ◽  
J. Katz
Keyword(s):  
Unsteady Flow ◽  
Centrifugal Pump ◽  
Pressure Difference ◽  
Pressure Fluctuations ◽  
Primary Sources ◽  
Pressure Measurements ◽  
Local Pressure ◽  
Pressure Distributions ◽  
Flow Pressure ◽  
Tip Of The Tongue

Maps of pressure distributions computed using PDV data, combined with noise and local pressure measurements, are used for identifying primary sources of noise in a centrifugal pump. In the vicinity of the impeller pressure minima occur around the blade and near a vortex train generated as a result of non-uniform outflux from the impeller. The pressure everywhere also varies depending on the orientation of the impeller relative to the tongue. Noise peaks are generated when the pressure difference across the tongue is maximum, probably due to tongue oscillations, and when the wake impinges on the tip of the tongue.

Experimental Investigation of Pressure Fluctuations on Inner Wall of a Centrifugal Pump

2019 ◽  
Vol 36 (4) ◽  
pp. 401-410 ◽  
Author(s):  
Xiao-Qi Jia ◽  
Bao-Ling Cui ◽  
Zu-Chao Zhu ◽  
Yu-Liang Zhang
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Pressure Fluctuations ◽  
High Flow ◽  
Low Flow ◽  
Centrifugal Pumps ◽  
Flow Rates ◽  
Pressure Distributions ◽  
Blade Passing Frequency

Abstract Affected by rotor–stator interaction and unstable inner flow, asymmetric pressure distributions and pressure fluctuations cannot be avoided in centrifugal pumps. To study the pressure distributions on volute and front casing walls, dynamic pressure tests are carried out on a centrifugal pump. Frequency spectrum analysis of pressure fluctuation is presented based on Fast Fourier transform and steady pressure distribution is obtained based on time-average method. The results show that amplitudes of pressure fluctuation and blade-passing frequency are sensitive to the flow rate. At low flow rates, high-pressure region and large pressure gradients near the volute tongue are observed, and the main factors contributing to the pressure fluctuation are fluctuations in blade-passing frequency and high-frequency fluctuations. By contrast, at high flow rates, fluctuations of rotating-frequency and low frequencies are the main contributors to pressure fluctuation. Moreover, at low flow rates, pressure near volute tongue increases rapidly at first and thereafter increases slowly, whereas at high flow rates, pressure decreases sharply. Asymmetries are observed in the pressure distributions on both volute and front casing walls. With increasing of flow rate, both asymmetries in the pressure distributions and magnitude of the pressure decrease.

Effects of short blades on performance and inner flow characteristics of a low-specific-speed centrifugal pump

2017 ◽  
Vol 231 (4) ◽  
pp. 290-302 ◽  
Author(s):  
Can Kang ◽  
Ning Mao ◽  
Chen Pan ◽  
Yang Zhu ◽  
Bing Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Low Flow ◽  
Back Surface ◽  
Flow Rates ◽  
Pump Operation ◽  
Low Specific Speed ◽  
Specific Speed

A low-specific-speed centrifugal pump equipped with long and short blades is studied. Emphasis is placed on the pump performance and inner flow characteristics at low flow rates. Each short blade is intentionally shifted towards the back surface of the neighboring long blade, and the outlet parts of the short blades are uniformly shortened. Unsteady numerical simulation is conducted to disclose inner flow patterns associated with the modified design. Thereby, a comparison is enabled between the two schemes featured by different short blades. Both practical operation data and numerical results support that the deviation and cutting of the short blades can eliminate the positive slope of pump head curve at low flow rates. Therefore, the modification of short blades improves the pump operation stability. Due to the shortening of the outlet parts of the short blades, velocity distributions between impeller outlet and radial diffuser inlet exhibit explicitly altered circumferential flow periodicity. Pressure fluctuations in the radial diffuser are complex in terms of diversified periodicity and amplitudes. Flow rate influences pressure fluctuations in the radial diffuser considerably. As flow rate decreases, the regularity of the orbit of hydraulic loads exerted upon the impeller collapses while hydraulic loads exerted upon the short blades remain circumferentially periodic.

Unsteady Flow Structure on a Centrifugal Pump: Experimental and Numerical Approaches

2002 ◽  
Author(s):  
Jose´ Gonza´lez ◽  
Carlos Santolaria ◽  
Eduardo Blanco ◽  
Joaqui´n Ferna´ndez
Keyword(s):  
Numerical Model ◽  
Centrifugal Pump ◽  
Pressure Field ◽  
Pressure Fluctuations ◽  
Side Wall ◽  
Relative Effect ◽  
Pressure Transducers ◽  
Unsteady Pressure ◽  
Blade Passing Frequency ◽  
Wide Range

Both experimental and numerical studies of the unsteady pressure field inside a centrifugal pump have been carried out. The unsteady patterns found for the pressure fluctuations are compared and a further and more detailed flow study from the numerical model developed will be presented in this paper. Measurements were carried out with pressure transducers installed on the volute shroud. At the same time, the unsteady pressure field inside the volute of a centrifugal pump has been numerically modelled using a finite volume commercial code and the dynamic variables obtained have been compared with the experimental data available. In particular, the amplitude of the fluctuating pressure field in the shroud side wall of the volute at the blade passing frequency is successfully captured by the model for a wide range of operating flow rates. Once the developed numerical model has shown its capability in describing the unsteady patterns experimentally measured, an explanation for such patterns is searched. Moreover, the possibilities of the numerical model can be extended to other sections (besides the shroud wall of the volute), which can provide plausible explanations for the dynamic interaction effects between the flow at the impeller exit and the volute tongue at different axial positions. The results of the numerical simulation are focused in the blade passing frequency in order to study the relative effect of the two main phenomena occurring at that frequency for a given position: the blade passing in front of the tongue and the wakes of the blades.

Influence of wall roughness on the static performance and pressure fluctuation characteristics of a double-suction centrifugal pump

2018 ◽  
Vol 232 (7) ◽  
pp. 826-840 ◽  
Author(s):  
Zhifeng Yao ◽  
Min Yang ◽  
Ruofu Xiao ◽  
Fujun Wang
Keyword(s):  
Centrifugal Pump ◽  
Pressure Fluctuation ◽  
Pressure Fluctuations ◽  
Design Flow ◽  
Experimental Investigations ◽  
Wall Roughness ◽  
Detached Eddy Simulation ◽  
Centrifugal Pumps ◽  
Eddy Simulation ◽  
Static Performance

The unsteady flow field and pressure fluctuations in double-suction centrifugal pumps are greatly affected by the wall roughness of internal surfaces. To determine the wall roughness effect, numerical and experimental investigations were carried out. Three impeller schemes for different wall roughness were solved using detached eddy simulation, and the performance and pressure fluctuations resolved by detached eddy simulation were compared with the experimental data. The results show that the effects of wall roughness on the static performance of a pump are remarkable. The head and efficiency of the tested double-suction centrifugal pump are raised by 2.53% and 6.60% respectively as the wall roughness is reduced by means of sand blasting and coating treatments. The detached eddy simulation method has been proven to be accurate for the prediction of the head and efficiency of the double-suction centrifugal pump with roughness effects. The influence of the roughness on pressure fluctuation is greatly dependent on the location relative to the volute tongue region. For locations close to the volute tongue, the peak-to-peak value of the pressure fluctuations of a wall roughness of Ra = 0.10 mm may be 23.27% larger than the case where Ra = 0.02 mm at design flow rate.

Relationship Between Flow Instability and Performance of a Centrifugal Pump With a Volute

2020 ◽  
Vol 142 (11) ◽  
Author(s):  
Hyeon-Seok Shim ◽  
Kwang-Yong Kim
Keyword(s):  
Centrifugal Pump ◽  
Numerical Solutions ◽  
Flow Instability ◽  
Pressure Fluctuations ◽  
Three Dimensional ◽  
Performance Characteristics ◽  
Recovery Coefficient ◽  
Partial Load ◽  
And Performance ◽  
Static Head

Abstract Flow instability and its correlations with performance characteristics were investigated for a centrifugal pump with a volute. Unsteady three-dimensional Reynolds-averaged Navier–Stokes analysis was performed to analyze the flow and performance characteristics using the shear stress transport (SST) turbulence model. The grid dependence and temporal resolution were tested to evaluate the numerical uncertainties, and the numerical solutions were validated using experimental data. The total-to-static head coefficient, the impeller's total-to-static head coefficient, and the volute static pressure recovery coefficient were selected as performance parameters. To identify the flow instability, pressure fluctuations were monitored upstream of the impeller, at the volute inlet, and on the shroud wall of the impeller. Three different types of flow instability were detected in partial-load conditions: inside the volute, upstream of the impeller, and at the interface between the impeller and volute. The time-dependent flow structures were investigated to obtain insight into the onset of the flow instability. The correlation of the onset of the flow instability with the performance curves was discussed.

scholarly journals Flow Characteristics in Volute of a Double-Suction Centrifugal Pump with Different Impeller Arrangements

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 669 ◽  
Author(s):  
Yu Song ◽  
Honggang Fan ◽  
Wei Zhang ◽  
Zhifeng Xie
Keyword(s):  
Centrifugal Pump ◽  
High Efficiency ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Weighted Average ◽  
Complex Flow ◽  
Suction Pump ◽  
Impeller Outlet ◽  
Large Flow ◽  
Dominant Frequencies

As an important type of centrifugal pump, the double-suction pump has been widely used due to its high efficiency region and large flow rate. In the present study, the complex flow in volute of a double-suction centrifugal pump is investigated by numerical simulation using a re-normalization group (RNG) k-ε model with experimental validation. Axial flows are observed in volute near the impeller outlet and compared with four staggered angles. The net area-weighted average axial velocities decrease as the staggered angle increases. The axial flows are mainly caused by the different circumferential pressure distribution at the twin impeller outlet. The dominant frequencies of the axial velocities for different staggered angles are fBP and its harmonic. The pressure fluctuations in most regions of the volute are obtained by superimposing the pressure generated by the two impellers.

3D Quasi-Unsteady Flow Simulation in a Centrifugal Pump: Comparison With the Experimental Results

2004 ◽  
Author(s):  
Miguel Asuaje ◽  
Farid Bakir ◽  
Andres Tremante ◽  
Ricardo Noguera ◽  
Robert Rey
Keyword(s):  
Unsteady Flow ◽  
Centrifugal Pump ◽  
Cfd Simulation ◽  
Pressure Fluctuations ◽  
Pressure Sensors ◽  
Flow Simulation ◽  
Turbulence Models ◽  
Numerical Predictions ◽  
Radial Thrust ◽  
Unsteady Flow Simulation

A 3D-CFD simulation of the impeller and volute casing of a centrifugal pump has been performed using commercial codes CFX 5.5 and CFX-TASCflow 2.12. The pump has an specific speed of 32 (metric units) and an outside impeller diameter of 400 mm. First, a 3D-flow simulation for the isolated impeller with a structured grid is presented. A sensitivity analysis regarding grid quality and turbulence models were also performed. A 3D quasi-unsteady flow simulation of the impeller-volute assembly is presented, as well. This flow simulation was carried out for several impeller blades and volute tongue relative positions. As a result, the radial thrust on the pump shaft were calculated for different flow rates. Experimental test were carried out in order to compare theoretical pressure fluctuations with the experimental ones measured by various unsteady pressure sensors placed on the impeller shroud and volute. The qualitative and quantitative results ratify numerical predictions.

scholarly journals Pressure Fluctuations due to Air Entrainment in a Screw-Type Centrifugal Pump.

2000 ◽  
Vol 66 (644) ◽  
pp. 1126-1131 ◽  
Author(s):  
You-Taek KIM ◽  
Kazuhiro TANAKA ◽  
Iyoji YAMADA ◽  
Yoichiro MATSUMOTO
Keyword(s):  
Centrifugal Pump ◽  
Pressure Fluctuations ◽  
Air Entrainment
Sign in / Sign up

Export Citation Format

Share Document