scholarly journals Numerical quantification of the impact of microstructure on the mechanical behavior of particulate Al/SiC composites in 2D

2017 ◽  
Vol 117 ◽  
pp. 91-103 ◽  
Author(s):  
Bowen Liang ◽  
Anand Nagarajan ◽  
Soheil Soghrati
Keyword(s):  
Mechanical Behavior ◽  
Sic Composites ◽  
The Impact

scholarly journals Influence of SiC Content on Microstructure, Dislocation Density and Mechanical Behavior of Cu/SiC Composite

2022 ◽  
Vol 24 (1) ◽  
pp. 186-200
Author(s):  
H. A. EL-Fattah ◽  
◽  
M.A. Metwally ◽  
M. M. Sadawy ◽  
I .G.El- Batanony ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Mechanical Behavior ◽  
Volume Fraction ◽  
Percentage Increase ◽  
Sintering Process ◽  
Xrd Diffraction ◽  
Microstructure Examination ◽  
Sic Composites ◽  
The Impact ◽  
Pure Cu

The present investigation has examined the impact of micro-SiC on microstructure, dislocation and mechanical behavior of Cu/SiC composite. The micro-composite samples have been fabricated under a constant pressure (480 MPa) and sintered temperature (860oC) for 2 h. The sintering process was performed under argon gas. The microstructure examination was conducted using SEM/EDS and XRD diffraction. The SiC contents were 0, 5, 10,15,20,25 and 30 volume fraction. The outcomes showed that the density was significantly decreased with an increase of silicon carbide content. The relative densities of Cu and Cu/SiC composites was ranged from 91.24% to 83.56% for pure Cu and Cu/30 vol%SiC composites. The copper crystallite size was reduced with growing SiC content while the hardness, ultimate and yield compressive strength increased with increment of SiC volume fraction to 20% vol. The values of hardness, ultimate and yield compressive strength increased to 231 HV,343 and 176 N/mm2 , respectively for the composite sample containing 20% SiC particles with a percentage increase of 75%,26.6% and 57.2% compared with pure Cu.

scholarly journals The effect of the outlet angle β2 on the thermomechanical behavior of a centrifugal compressor blade

2020 ◽  
Vol 29 (1) ◽  
pp. 1-8
Author(s):  
Ahmed Allali ◽  
Sadia Belbachir ◽  
Ahmed Alami ◽  
Belhadj Boucham ◽  
Abdelkader Lousdad
Keyword(s):  
Mechanical Behavior ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Complex Form ◽  
Compressor Blade ◽  
Stress Fields ◽  
The Finite Element Method ◽  
Mechanical Fatigue ◽  
Outlet Angle ◽  
The Impact

AbstractThe objective of this work lies in the three-dimensional study of the thermo mechanical behavior of a blade of a centrifugal compressor. Numerical modeling is performed on the computational code "ABAQUS" based on the finite element method. The aim is to study the impact of the change of types of blades, which are defined as a function of wheel output angle β2, on the stress fields and displacements coupled with the variation of the temperature.This coupling defines in a realistic way the thermo mechanical behavior of the blade where one can note the important concentrations of stresses and displacements in the different zones of its complex form as well as the effects at the edges. It will then be possible to prevent damage and cracks in the blades of the centrifugal compressor leading to its failure which can be caused by the thermal or mechanical fatigue of the material with which the wheel is manufactured.

Mechanical behavior of SiCf/SiC composites with alternating PyC/SiC multilayer interphases

2013 ◽  
Vol 44 ◽  
pp. 320-324 ◽  
Author(s):  
Haijiao Yu ◽  
Xingui Zhou ◽  
Wei Zhang ◽  
Huaxin Peng ◽  
Changrui Zhang
Keyword(s):  
Mechanical Behavior ◽  
Sic Composites

Investigation on Mechanical Properties of Fibreglass Reinforced Flexible Pipes Under Torsion

2018 ◽  
Author(s):  
Pan Fang ◽  
Yuxin Xu ◽  
Shuai Yuan ◽  
Yong Bai ◽  
Peng Cheng
Keyword(s):  
Mechanical Behavior ◽  
Torsion Angle ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Load Condition ◽  
Element Model ◽  
Flexible Pipe ◽  
Torsional Load ◽  
Flexible Pipes ◽  
The Impact

Fibreglass reinforced flexible pipe (FRFP) is regarded as a great alternative to many bonded flexible pipes in the field of oil or gas transportation in shallow water. This paper describes an analysis of the mechanical behavior of FRFP under torsion. The mechanical behavior of FRFP subjected to pure torsion was investigated by experimental, analytical and numerical methods. Firstly, this paper presents experimental studies of three 10-layer FRFP subjected to torsional load. Torque-torsion angle relations were recorded during this test. Then, a theoretical model based on three-dimensional (3D) anisotropic elasticity theory was proposed to study the mechanical behavior of FRFP. In addition, a finite element model (FEM) including reinforced layers and PE layers was used to simulate the torsional load condition in ABAQUS. Torque-torsion angle relations obtained from these three methods agree well with each other, which illustrates the accuracy and reliability of the analytical model and FEM. The impact of fibreglass winding angle, thickness of reinforced layers and radius-thickness ratio were also studied. Conclusions obtained from this research may be of great practicality to manufacturing engineers.

The Impact of Surface Charge on the Mechanical Behavior of High-Porosity Chalk

2012 ◽  
Vol 46 (5) ◽  
pp. 1073-1090 ◽  
Author(s):  
M. Megawati ◽  
A. Hiorth ◽  
M. V. Madland
Keyword(s):  
Mechanical Behavior ◽  
Surface Charge ◽  
High Porosity ◽  
The Impact

Mechanical Behavior of 2D C/SiC Composites at Elevated Temperatures under Uniaxial Compression

2011 ◽  
Vol 462-463 ◽  
pp. 1-6 ◽  
Author(s):  
Tao Suo ◽  
Yu Long Li ◽  
Ming Shuang Liu
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
Carbon Fiber ◽  
Mechanical Behavior ◽  
Uniaxial Compression ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Carbon Matrix ◽  
Structural Applications ◽  
Sic Composites

As Carbon-fiber-reinforced SiC-matrix (C/SiC) composites are widely used in high-temperature structural applications, its mechanical behavior at high temperature is important for the reliability of structures. In this paper, mechanical behavior of a kind of 2D C/SiC composite was investigated at temperatures ranging from room temperature (20C) to 600C under quasi-static and dynamic uniaxial compression. The results show the composite has excellent high temperature mechanical properties at the tested temperature range. Catastrophic brittle failure is not observed for the specimens tested at different strain rates. The compressive strength of the composite deceases only 10% at 600C if compared with that at room temperature. It is proposed that the decrease of compressive strength of the 2D C/SiC composite at high temperature is influenced mainly by release of thermal residual stresses in the reinforced carbon fiber and silicon carbon matrix and oxidation of the composite in high temperature atmosphere.

Mechanical Behavior of Heat Activated Film Adhesives

2021 ◽  
Author(s):  
Prabhat Janamanchi ◽  
Abhijit Dasgupta ◽  
Narendra Singh
Keyword(s):  
Mechanical Behavior ◽  
Thermal Exposure ◽  
Melting Transition ◽  
Preliminary Evaluation ◽  
Curing Conditions ◽  
Structural Applications ◽  
History Of ◽  
Favorable Conditions ◽  
The Impact ◽  
Curing Age

Abstract Heat activated film (HAF) adhesives enable the bonding of materials that are difficult to bond with conventional adhesives where one of the substrates is flexible. Although they are traditionally found in the context of industrial and structural applications, they are increasingly finding use in in electronic products. This paper provides a preliminary evaluation of the mechanical behavior of HAFs. Two commercial polyurethane HAF formulations (designated as HAF-II and HAF-III, for the purpose of this paper) were evaluated to assess the dependence of the mechanical properties on phase transitions and on the thermal exposure history of the material. Both factors were found to play a significant role in determining the overall usability of the materials. The melting transition occurs under 50°C for both materials, after which their stiffness drops significantly. Among the two, HAF-III is preferable as it undergoes a delayed melting transition, effectively extending the usable operating temperature range. As with any adhesive, there are several other factors that can influence the performance of adhesives such as post-curing age, storage, and curing conditions to name a few. The impact of these factors on the material’s strength is also discussed in brief and a recommendation for favorable conditions is provided.

Sign in / Sign up

Export Citation Format

Share Document