Mechanical Behavior of 2D C/SiC Composites at Elevated Temperatures under Uniaxial Compression

2011 ◽  
Vol 462-463 ◽  
pp. 1-6 ◽  
Author(s):  
Tao Suo ◽  
Yu Long Li ◽  
Ming Shuang Liu
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
Carbon Fiber ◽  
Mechanical Behavior ◽  
Uniaxial Compression ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Carbon Matrix ◽  
Structural Applications ◽  
Sic Composites

As Carbon-fiber-reinforced SiC-matrix (C/SiC) composites are widely used in high-temperature structural applications, its mechanical behavior at high temperature is important for the reliability of structures. In this paper, mechanical behavior of a kind of 2D C/SiC composite was investigated at temperatures ranging from room temperature (20C) to 600C under quasi-static and dynamic uniaxial compression. The results show the composite has excellent high temperature mechanical properties at the tested temperature range. Catastrophic brittle failure is not observed for the specimens tested at different strain rates. The compressive strength of the composite deceases only 10% at 600C if compared with that at room temperature. It is proposed that the decrease of compressive strength of the 2D C/SiC composite at high temperature is influenced mainly by release of thermal residual stresses in the reinforced carbon fiber and silicon carbon matrix and oxidation of the composite in high temperature atmosphere.

High-Temperature Compression Testing of Graphite

1953 ◽  
Vol 20 (2) ◽  
pp. 289-294
Author(s):  
Leon Green
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Temperature ◽  
Stress Relaxation ◽  
Temperature Control ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Limited Degree ◽  
Relaxation Curves ◽  
Short Time

Abstract Experiments on the compression of graphite cylinders at elevated temperatures are described. It is found that the short-time compressive strength increases with temperature in the range from room temperature to 2000 C, a variation which is consistent with the previously reported behavior of the tensile strength. Photographs of typical modes of deformation and their corresponding stress-strain curves are presented, but a limited degree of temperature control renders the curves semiquantitative in nature. The large, mutually opposing influences of temperature and strain rate are illustrated by photographs of typical failures, and stress-relaxation curves manifest the plasticity of graphite at high temperatures.

Phase transformation and layer evolution in molybdenum disilicide-silicon carbide nanolayered coatings

1994 ◽  
Vol 52 ◽  
pp. 538-539
Author(s):  
H. Kung ◽  
T. R. Jervis ◽  
J.-P. Hirvonen ◽  
M. Nastasi ◽  
T. E. Mitchell ◽  
...  
Keyword(s):  
Phase Transformation ◽  
High Temperature ◽  
Oxidation Resistance ◽  
Elevated Temperatures ◽  
Matrix Material ◽  
Molybdenum Disilicide ◽  
High Temperature Strength ◽  
Cross Sectional ◽  
Good Oxidation Resistance ◽  
Structural Applications

MoSi2 is a potential matrix material for high temperature structural composites due to its high melting temperature and good oxidation resistance at elevated temperatures. The two major drawbacksfor structural applications are inadequate high temperature strength and poor low temperature ductility. The search for appropriate composite additions has been the focus of extensive investigations in recent years. The addition of SiC in a nanolayered configuration was shown to exhibit superior oxidation resistance and significant hardness increase through annealing at 500°C. One potential application of MoSi2- SiC multilayers is for high temperature coatings, where structural stability ofthe layering is of major concern. In this study, we have systematically investigated both the evolution of phases and the stability of layers by varying the heat treating conditions.Alternating layers of MoSi2 and SiC were synthesized by DC-magnetron and rf-diode sputtering respectively. Cross-sectional transmission electron microscopy (XTEM) was used to examine three distinct reactions in the specimens when exposed to different annealing conditions: crystallization and phase transformation of MoSi2, crystallization of SiC, and spheroidization of the layer structures.

FANSTEEL 85 METAL

Alloy Digest ◽  
1981 ◽  
Vol 30 (6) ◽  
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Creep Strength ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Base Alloy ◽  
Heat Treating ◽  
Good Combination ◽  
Bend Strength ◽  
Temperature Performance

Abstract FANSTEEL 85 METAL is a columbium-base alloy characterized by good fabricability at room temperature, good weldability and a good combination of creep strength and oxidation resistance at elevated temperatures. Its applications include missile and rocket components and many other high-temperature parts. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, tensile properties, and bend strength as well as creep. It also includes information on low and high temperature performance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Cb-7. Producer or source: Fansteel Metallurgical Corporation. Originally published December 1963, revised June 1981.

CARPENTER T-K

Alloy Digest ◽  
1969 ◽  
Vol 18 (5) ◽  
Keyword(s):  
Wear Resistance ◽  
Compressive Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Elevated Temperatures ◽  
Heat Treating ◽  
Extrusion Dies ◽  
Temperature Performance ◽  
Red Hardness

Abstract Carpenter T-K is a tungsten-chromium type hot-work steel having good red-hardness and resistance to abrasion. It will withstand high operating temperatures up to 1000 F for long periods. It is recommended for hot shear blades, forging and extrusion dies, hot compression tools, and similar applications where high compressive strength and wear resistance at elevated temperatures are required. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on high temperature performance as well as forming, heat treating, machining, and joining. Filing Code: TS-219. Producer or source: Carpenter.

scholarly journals Undergraduate Research Program to Recycle Composite Waste

2021 ◽  
Vol 11 (7) ◽  
pp. 354
Author(s):  
Waleed Ahmed ◽  
Essam Zaneldin ◽  
Amged Al Hassan
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Carbon Fiber ◽  
Undergraduate Students ◽  
Research Program ◽  
Modulus Of Elasticity ◽  
Undergraduate Research ◽  
Undergraduate Research Program ◽  
Structural Applications ◽  
Cfrp Composite

With the rapid growth in the manufacturing industry and increased urbanization, higher amounts of composite material waste are being produced, causing severe threats to the environment. These environmental concerns, coupled with the fact that undergraduate students typically have minimal experience in research, have initiated the need at the UAE University to promote research among undergraduate students, leading to the development of a summer undergraduate research program. In this study, a recycling methodology is presented to test lab-fabricated Carbon-Fiber-Reinforced Polymer (CFRP) for potential applications in industrial composite waste. The work was conducted by two groups of undergraduate students at the UAE University. The methodology involved the chemical dissolution of the composite waste, followed by compression molding and adequate heat treatment for rapid curing of CFRP. Subsequently, the CFRP samples were divided into three groups based on their geometrical distinctions. The mechanical properties (i.e., modulus of elasticity and compressive strength) were determined through material testing, and the results were then compared with steel for prompt reference. The results revealed that the values of mechanical properties range from 2 to 4.3 GPa for the modulus of elasticity and from 203.7 to 301.5 MPa for the compressive strength. These values are considered competitive and optimal, and as such, carbon fiber waste can be used as an alternate material for various structural applications. The inconsistencies in the values are due to discrepancies in the procedure as a result of the lack of specialized equipment for handling CFRP waste material. The study concluded that the properties of CFRP composite prepreg scrap tend to be reusable instead of disposable. Despite the meager experimental discrepancies, test values and mechanical properties indicate that CFRP composite can be successfully used as a material for nonstructural applications.

Effects of Elevated Temperatures on the Compressive Strength of HFCC

2011 ◽  
Vol 261-263 ◽  
pp. 416-420 ◽  
Author(s):  
Fu Ping Jia ◽  
Heng Lin Lv ◽  
Yi Bing Sun ◽  
Bu Yu Cao ◽  
Shi Ning Ding
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Relative Strength ◽  
Ordinary Concrete ◽  
Residual Compressive Strength ◽  
Fly Ash Concrete ◽  
The Relationship

This paper presents the results of elevated temperatures on the compressive of high fly ash content concrete (HFCC). The specimens were prepared with three different replacements of cement by fly ash 30%, 40% and 50% by mass and the residual compressive strength was tested after exposure to elevated temperature 250, 450, 550 and 650°C and room temperature respectively. The results showed that the compressive strength apparently decreased with the elevated temperature increased. The presence of fly ash was effective for improvement of the relative strength, which was the ratio of residual compressive strength after exposure to elevated temperature and ordinary concrete. The relative compressive strength of fly ash concrete was higher than those of ordinary concrete. Based on the experiments results, the alternating simulation formula to determine the relationship among relative strength, elevated temperature and fly ash replacement is developed by using regression of results, which provides the theoretical basis for the evaluation and repair of HFCC after elevated temperature.

scholarly journals Experimental Study on the Effect of Basalt Fiber and Sodium Alginate in Polymer Concrete Exposed to Elevated Temperature

Processes ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 510
Author(s):  
Seyed Esmaeil Mohammadyan-Yasouj ◽  
Hossein Abbastabar Ahangar ◽  
Narges Ahevani Oskoei ◽  
Hoofar Shokravi ◽  
Seyed Saeid Rahimian Koloor ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Vinyl Ester ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Basalt Fiber ◽  
Polymer Concrete ◽  
Strength Increase ◽  
Extensive Literature ◽  
Polymer Binders ◽  
Preliminary Phase

Polymer concrete contains aggregates and a polymeric binder such as epoxy, polyester, vinyl ester, or normal epoxy mixture. Since polymer binders in polymer concrete are made of organic materials, they have a very low heat and fire resistance compared to minerals. This paper investigates the effect of basalt fibers (BF) and alginate on the compressive strength of polymer concrete. An extensive literature review was completed, then two experimental phases including the preliminary phase to set the appropriate mix design, and the main phase to investigate the compressive strength of samples after exposure to elevated temperatures of 100 °C, 150 °C, and 180 °C were conducted. The addition of BF and/or alginate decreases concrete compressive strength under room temperature, but the addition of BF and alginate each alone leads to compressive strength increase during exposure to heat and increase in the temperature to 180 °C showed almost positive on the compressive strength. The addition of BF and alginate both together increases the rate of strength growth of polymer concrete under heat from 100 °C to 180 °C. In conclusion, BF and alginate decrease the compressive strength of polymer concretes under room temperature, but they improve the resistance against raised temperatures.

Martensite decomposition during post-heat treatments and the aging response of near-α Ti–6Al–2Sn–4Zr–2Mo (Ti-6242) titanium alloy processed by selective laser melting (SLM)

2021 ◽  
pp. 2050018
Author(s):  
Haiyang Fan ◽  
Yahui Liu ◽  
Shoufeng Yang
Keyword(s):  
Titanium Alloy ◽  
High Temperature ◽  
Titanium Alloys ◽  
Selective Laser Melting ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Aging Treatment ◽  
Water Quenching ◽  
Laser Melting ◽  
Aging Response

Ti–6Al–2Sn–4Zr–2Mo (Ti-6242), a near-[Formula: see text] titanium alloy explicitly designed for high-temperature applications, consists of a martensitic structure after selective laser melting (SLM). However, martensite is thermally unstable and thus adverse to the long-term service at high temperatures. Hence, understanding martensite decomposition is a high priority for seeking post-heat treatment for SLMed Ti-6242. Besides, compared to the room-temperature titanium alloys like Ti–6Al–4V, aging treatment is indispensable to high-temperature near-[Formula: see text] titanium alloys so that their microstructures and mechanical properties are pre-stabilized before working at elevated temperatures. Therefore, the aging response of the material is another concern of this study. To elaborate the two concerns, SLMed Ti-6242 was first isothermally annealed at 650[Formula: see text]C and then water-quenched to room temperature, followed by standard aging at 595[Formula: see text]C. The microstructure analysis revealed a temperature-dependent martensite decomposition, which proceeded sluggishly at [Formula: see text]C despite a long duration but rapidly transformed into lamellar [Formula: see text] above the martensite transition zone (770[Formula: see text]C). As heating to [Formula: see text]C), it produced a coarse microstructure containing new martensites formed in water quenching. The subsequent mechanical testing indicated that SLM-built Ti-6242 is excellent in terms of both room- and high-temperature tensile properties, with around 1400 MPa (UTS)[Formula: see text]5% elongation and 1150 MPa (UTS)[Formula: see text]10% elongation, respectively. However, the combination of water quenching and aging embrittled the as-built material severely.

scholarly journals Development of Creep-Resistant, Alumina-Forming Ferrous Alloys for High-Temperature Structural Use

2018 ◽  
Author(s):  
Y. Yamamoto ◽  
M. P. Brady ◽  
G. Muralidharan ◽  
B. A. Pint ◽  
P. J. Maziasz ◽  
...  
Keyword(s):  
High Temperature ◽  
Elevated Temperatures ◽  
Extreme Environments ◽  
Alloy Design ◽  
Austenitic Steels ◽  
Strength Development ◽  
Second Phase ◽  
Ferrous Alloys ◽  
Steel Alloys ◽  
Structural Applications

This paper overviews recent advances in developing novel alloy design concepts of creep-resistant, alumina-forming Fe-base alloys, including both ferritic and austenitic steels, for high-temperature structural applications in fossil-fired power generation systems. Protective, external alumina-scales offer improved oxidation resistance compared to chromia-scales in steam-containing environments at elevated temperatures. Alloy design utilizes computational thermodynamic tools with compositional guidelines based on experimental results accumulated in the last decade, along with design and control of the second-phase precipitates to maximize high-temperature strengths. The alloys developed to date, including ferritic (Fe-Cr-Al-Nb-W base) and austenitic (Fe-Cr-Ni-Al-Nb base) alloys, successfully incorporated the balanced properties of steam/water vapor-oxidation and/or ash-corrosion resistance and improved creep strength. Development of cast alumina-forming austenitic (AFA) stainless steel alloys is also in progress with successful improvement of higher temperature capability targeting up to ∼1100°C. Current alloy design approach and developmental efforts with guidance of computational tools were found to be beneficial for further development of the new heat resistant steel alloys for various extreme environments.

scholarly journals Comparison of Mechanical and Microstructural Properties of as-Cast Al-Cu-Mg-Ag Alloys: Room Temperature vs. High Temperature

Crystals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1330
Author(s):  
Muhammad Farzik Ijaz ◽  
Mahmoud S. Soliman ◽  
Ahmed S. Alasmari ◽  
Adel T. Abbas ◽  
Faraz Hussain Hashmi
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Mechanical Testing ◽  
Tensile Testing ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Microstructural Properties ◽  
Testing Environments ◽  
Mechanical And Microstructural Properties ◽  
Mg Content

Unfolding the structure–property linkages between the mechanical performance and microstructural characteristics could be an attractive pathway to develop new single- and polycrystalline Al-based alloys to achieve ambitious high strength and fuel economy goals. A lot of polycrystalline as-cast Al-Cu-Mg-Ag alloy systems fabricated by conventional casting techniques have been reported to date. However, no one has reported a comparison of mechanical and microstructural properties that simultaneously incorporates the effects of both alloy chemistry and mechanical testing environments for the as-cast Al-Cu-Mg-Ag alloy systems. This preliminary prospective paper presents the examined experimental results of two alloys (denoted Alloy 1 and Alloy 2), with constant Cu content of ~3 wt.%, Cu/Mg ratios of 12.60 and 6.30, and a constant Ag of 0.65 wt.%, and correlates the synergistic comparison of mechanical properties at room and elevated temperatures. According to experimental results, the effect of the precipitation state and the mechanical properties showed strong dependence on the composition and testing environments for peak-aged, heat-treated specimens. In the room-temperature mechanical testing scenario, the higher Cu/Mg ratio alloy with Mg content of 0.23 wt.% (Alloy 1) possessed higher ultimate tensile strength when compared to the low Cu/Mg ratio with Mg content of 0.47 wt.% (Alloy 2). From phase constitution analysis, it is inferred that the increase in strength for Alloy 1 under room-temperature tensile testing is mainly ascribable to the small grain size and fine and uniform distribution of θ precipitates, which provided a barrier to slip by deaccelerating the dislocation movement in the room-temperature environment. Meanwhile, Alloy 2 showed significantly less degradation of mechanical strength under high-temperature tensile testing. Indeed, in most cases, low Cu/Mg ratios had a strong influence on the copious precipitation of thermally stable omega phase, which is known to be a major strengthening phase at elevated temperatures in the Al-Cu-Mg-Ag alloying system. Consequently, it is rationally suggested that in the high-temperature testing scenario, the improvement in mechanical and/or thermal stability in the case of the Alloy 2 specimen was mainly due to its compositional design.

Sign in / Sign up

Export Citation Format

Share Document