Optimization of continuous drive friction welding process for AA6061-T6 circular pipe and conical head

Structures ◽  
2022 ◽  
Vol 36 ◽  
pp. 1068-1079
Author(s):  
Dabin Yang ◽  
Xiangyi Sun ◽  
Guangen Zhou ◽  
Hongquan Jiang ◽  
Litai Sun ◽  
...  
Keyword(s):  
Friction Welding ◽  
Welding Process ◽  
Circular Pipe

Efficiency of the Inertia Friction Welding Process and Its Dependence on Process Parameters

2017 ◽  
Vol 48 (7) ◽  
pp. 3328-3342 ◽  
Author(s):  
O. N. Senkov ◽  
D. W. Mahaffey ◽  
D. J. Tung ◽  
W. Zhang ◽  
S. L. Semiatin
Keyword(s):  
Process Parameters ◽  
Friction Welding ◽  
Welding Process ◽  
Inertia Friction Welding

scholarly journals Microstructure and Mechanical Properties of Dissimilar Friction Welding Ti-6Al-4V Alloy to Nitinol

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 109
Author(s):  
Ateekh Ur Rehman ◽  
Nagumothu Kishore Babu ◽  
Mahesh Kumar Talari ◽  
Yusuf Siraj Usmani ◽  
Hisham Al-Khalefah
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flow Stress ◽  
Intermetallic Compound ◽  
Ultimate Tensile Strength ◽  
Friction Welding ◽  
Welding Process ◽  
Weld Interface ◽  
Dissimilar Joints ◽  
Dissimilar Alloys

In the present study, a friction welding process was adopted to join dissimilar alloys of Ti-Al-4V to Nitinol. The effect of friction welding on the evolution of welded macro and microstructures and their hardnesses and tensile properties were studied and discussed in detail. The macrostructure of Ti-6Al-4V and Nitinol dissimilar joints revealed flash formation on the Ti-6Al-4V side due to a reduction in flow stress at high temperatures during friction welding. The optical microstructures revealed fine grains near the Ti-6Al-4V interface due to dynamic recrystallization and strain hardening effects. In contrast, the area nearer to the nitinol interface did not show any grain refinement. This study reveals that the formation of an intermetallic compound (Ti2Ni) at the weld interface resulted in poor ultimate tensile strength (UTS) and elongation values. All tensile specimens failed at the weld interface due to the formation of intermetallic compounds.

scholarly journals Structure Analysis and Design of Automobile plastic clutch pump body based on friction welding

2020 ◽  
Vol 316 ◽  
pp. 02001
Author(s):  
Jing Sheng ◽  
Aamir Sohail ◽  
Mengguang Wang ◽  
Zhimin Wang
Keyword(s):  
High Temperature ◽  
Structural Design ◽  
Friction Welding ◽  
Room Temperature ◽  
Welding Process ◽  
Structure Type ◽  
Mechanical Analysis ◽  
Analysis And Design ◽  
Technical Requirements ◽  
Design Requirements

In order to realize the need for lightweight automobiles through replacing steel with plastics, the research and development of the plastic clutch pump body based on the friction welding was carried out. For the clutch pump body connected by friction welding process between the upper pump body and the lower pump body, the technical requirements of pressure 14 MPa and durability (high temperature 7.0 × 104 times, room temperature 7.0 × 105) are required. The structure type of the upper and lower pump bodies of the end face welding type was proposed. Through the static analysis of the pump body and weld and the mechanical analysis under the working condition, the structure of the clutch pump body (upper and lower pump body) was determined. According to the established welding process, the pressure of the clutch pump body is more than 15 MPa, and the number of high-temperature durable circulation and the number of room temperature durable circulation also reached 7.2×104 and 7.3×105 times respectively. The results show that the structural design of a clutch pump body meets the design requirements.

METALLURGICAL AND CORROSION CHARACTERIZATION OF POST WELD HEAT TREATED DUPLEX STAINLESS STEEL (UNS S31803) JOINTS BY FRICTION WELDING PROCESS

2016 ◽  
Vol 23 (03) ◽  
pp. 1650013 ◽  
Author(s):  
MOHAMMED ASIF M. ◽  
KULKARNI ANUP SHRIKRISHNA ◽  
P. SATHIYA
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Friction Welding ◽  
Volume Fraction ◽  
Welding Process ◽  
Equilibrium Temperature ◽  
Weld Interface ◽  
Heat Treated ◽  
Weld Heat

The present study focuses on the metallurgical and corrosion characterization of post weld heat treated duplex stainless steel joints. After friction welding, it was confirmed that there is an increase in ferrite content at weld interface due to dynamic recrystallization. This caused the weldments prone to pitting corrosion attack. Hence the post weld heat treatments were performed at three temperatures 1080[Formula: see text]C, 1150[Formula: see text]C and 1200[Formula: see text]C with 15[Formula: see text]min of aging time. This was followed by water and oil quenching. The volume fraction of ferrite to austenite ratio was balanced and highest pit nucleation resistance were achieved after PWHT at 1080[Formula: see text]C followed by water quench and at 1150[Formula: see text]C followed by oil quench. This had happened exactly at parameter set containing heating pressure (HP):40 heating time (HT):4 upsetting pressure (UP):80 upsetting time (UP):2 (experiment no. 5). Dual phase presence and absence of precipitates were conformed through TEM which follow Kurdjumov–Sachs relationship. PREN of ferrite was decreasing with increase in temperature and that of austenite increased. The equilibrium temperature for water quenching was around 1100[Formula: see text]C and that for oil quenching was around 1140[Formula: see text]C. The pit depths were found to be in the range of 100[Formula: see text]nm and width of 1.5–2[Formula: see text][Formula: see text]m.

Effect of Process Parameters on Welding Variables during Linear Friction Welding of Ti-6Al-4V Alloy

2011 ◽  
Vol 314-316 ◽  
pp. 979-983
Author(s):  
Tie Jun Ma ◽  
Xi Chen ◽  
Wen Ya Li
Keyword(s):  
Titanium Alloy ◽  
Process Parameters ◽  
Friction Welding ◽  
Welding Process ◽  
Orthogonal Experimental Design ◽  
Linear Friction Welding ◽  
Influence Of Process Parameters ◽  
Linear Friction ◽  
Suitable Process ◽  
Axial Shortening

The orthogonal experimental design was conducted for linear friction welding of Ti-6Al-4V titanium alloy (TC4). The friction power and joint temperature were collected during the welding process. The influence of process parameters on the axial shortening was analyzed. The suitable process parameters were determined by investigating the joint appearance, the requirement of axial shortening and welding variables during welding. The results provide important reference for establishing process parameters of linear friction welding in practice.

Sign in / Sign up

Export Citation Format

Share Document