scholarly journals Effect of carbon distribution range in mixed bainite / martensite / retained austenite microstructure on mechanical properties

2022 ◽  
Author(s):  
X.Y. Long ◽  
D.Y. Sun ◽  
K. Wang ◽  
F.C. Zhang ◽  
Z.N. Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Distribution Range ◽  
Carbon Distribution

scholarly journals The Effect of Different Annealing Strategies on the Microstructure Development and Mechanical Response of Austempered Steels

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1041
Author(s):  
Eliseo Hernandez-Duran ◽  
Luca Corallo ◽  
Tanya Ros-Yanez ◽  
Felipe Castro-Cerda ◽  
Roumen H. Petrov
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Mechanical Response ◽  
Steel Grade ◽  
The Other ◽  
Microstructure Development ◽  
Microstructural Refinement ◽  
Heterogeneous Distribution ◽  
Parent Austenite ◽  
Conventional Annealing

This study focuses on the effect of non-conventional annealing strategies on the microstructure and related mechanical properties of austempered steels. Multistep thermo-cycling (TC) and ultrafast heating (UFH) annealing were carried out and compared with the outcome obtained from a conventionally annealed (CA) 0.3C-2Mn-1.5Si steel. After the annealing path, steel samples were fast cooled and isothermally treated at 400 °C employing the same parameters. It was found that TC and UFH strategies produce an equivalent level of microstructural refinement. Nevertheless, the obtained microstructure via TC has not led to an improvement in the mechanical properties in comparison with the CA steel. On the other hand, the steel grade produced via a combination of ultrafast heating annealing and austempering exhibits enhanced ductility without decreasing the strength level with respect to TC and CA, giving the best strength–ductility balance among the studied steels. The outstanding mechanical response exhibited by the UFH steel is related to the formation of heterogeneous distribution of ferrite, bainite and retained austenite in proportions 0.09–0.78–0.14. The microstructural formation after UFH is discussed in terms of chemical heterogeneities in the parent austenite.

Effect of Si Content on Microstructure and Properties of 60Si2CrVA Spring Steel

2014 ◽  
Vol 968 ◽  
pp. 63-66 ◽  
Author(s):  
Fei Zhao ◽  
Zhan Ling Zhang ◽  
Jun Shuai Li ◽  
Cui Ye ◽  
Ni Li
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Testing Machine ◽  
Spring Steel ◽  
Impact Testing ◽  
X Ray ◽  
Comprehensive Properties ◽  
Spring Steels ◽  
Si Content

The microstructure and mechanical properties of the four spring steels with different Si content treated by Q-I-Q-T process were studied by metallographic microscope, MTS, impact testing machine and X-ray stress analyzer. The results show that the tensile strength and yield strength is first increased and then decreased with the increase of Si content, the volume fraction of retained austenite and elongation are fist decreased and then increased when the Si content is less than 2.1%, and the microstructure become finer and homogeneous. When Si content reaches 2.1%, the comprehensive properties of 60Si2CrVA spring steel is the best.

Microstructure and Properties of a Non-Quenched Prehardened Steel at Different Cooling Rate

2012 ◽  
Vol 524-527 ◽  
pp. 1976-1979
Author(s):  
Yi Luo ◽  
Jin Ming Peng
Keyword(s):  
Mechanical Properties ◽  
Fine Structure ◽  
Optical Microscopy ◽  
Cooling Rate ◽  
Retained Austenite ◽  
Transformation Products ◽  
Electronic Microscopy ◽  
Transmission Electronic Microscopy ◽  
Microstructure And Properties ◽  
Cooling Conditions

Mechanical properties of non-quenched prehardened (NQP) steel air cooled and sand cooled after forged were tested and their microstructure was investigated by optical microscopy and transmission electronic microscopy(TEM). The results show that mechanical properties of the NQP steel are similar at both cooling conditions, and their microstructure is bainite, whose fine structure is main bainite ferrite laths, retained austenite films, retained austenite islands and their transformation products. Bainite ferrite laths of the NQP steel air cooled are narrower than that sand cooled, while more retained austenite islands exist in latter.

Microstructure and Mechanical Properties of a Low-Carbon Steel Treated by One-Step Quenching and Partitioning Process

2014 ◽  
Vol 1082 ◽  
pp. 202-207 ◽  
Author(s):  
Shu Yan ◽  
Xiang Hua Liu
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Microstructural Evolution ◽  
Retained Austenite ◽  
Uniform Elongation ◽  
Low Carbon Steel ◽  
Total Elongation ◽  
Low Carbon ◽  
Quenching And Partitioning ◽  
Partitioning Time

A low carbon steel was treated by quenching and partitioning (Q&P) process, and a detailed characterization of the microstructural evolution and testing of mechanical properties were carried out. The resulted mechanical properties indicate that with the partitioning time increasing, the tensile strength decreases rapidly first and then remains stable, and the total elongation increases first then decreases. The investigated steel subjected to Q&P process exhibits excellent products of strength and elongation (17.8-20.6 GPa•%). The microstructural evolution of martensite matrix during the partitioning step was observed, and the morphology and content of retained austenite were characterized. The working hardening behavior of the samples was analyzed, and the retained austenite with higher carbon content contributes to the uniform elongation more effectively.

Effects of Cryogenic Treatment on the Microstructure and Mechanical Properties of High-alloyed Tool Steels

2020 ◽  
Vol 75 (5) ◽  
pp. 73-93
Author(s):  
Alwin Schulz ◽  
Chengsong Cui ◽  
Matthias Steinbacher ◽  
Tuncer Ümit ◽  
Martin Wunde ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Retained Austenite ◽  
Cryogenic Treatment ◽  
Homogeneous Distribution ◽  
Tool Steels ◽  
Positive Effects ◽  
Heat Treated ◽  
Primary Carbides ◽  
Complete Transformation

Abstract In this work, the influence of a cryogenic treatment on the microstructure, mechanical properties and wear resistance of the high-alloyed tool steels X38CrMoV5-3, X153CrMoV12 and ~X190CrVMo20-4 were investigated. Based on tempering curves of the steels, the heat treatment parameters were determined for the mechanical and wear specimens so that the conventionally heat-treated steels and the cryogenically treated steels featured similar hardness. The investigations showed that an almost complete transformation of retained austenite and a more homogeneous distribution of secondary carbides in the microstructure could be achieved by incorporating a cryogenic treatment. However, the cryogenic treatment does not show significantly positive effects on the investigated mechanical properties and wear resistance of the tool steels. The wear resistance of the samples was dominated by primary carbides. The cryogenic treatment would have a positive effect on large tool components with large wall thicknesses in terms of uniform and complete transformation of retained austenite throughout the entire components.

Application of Quenching-Partitioning-Tempering Process in Hot Rolled Plate Fabrication

2010 ◽  
Vol 654-656 ◽  
pp. 82-85 ◽  
Author(s):  
Shu Zhou ◽  
Ying Wang ◽  
Nai Lu Chen ◽  
Yong Hua Rong ◽  
Jian Feng Gu
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Significant Fraction ◽  
Rolled Plate ◽  
Quenching And Partitioning ◽  
Good Ductility ◽  
Hot Rolled ◽  
Rolled Plates

The quenching-partitioning-tempering (Q-P-T) process, based on the quenching and partitioning (Q&P) treatment, has been proposed for producing high strength steels containing significant fraction of film-like retained austenite and controlled amount of fine martensite laths. In this study, a set of Q-P-T processes for C-Mn-Si-Ni-Nb hot rolled plates are designed and realized. The steels with Q-P-T processes present a combination of high strength and relatively good ductility. The origin of such mechanical properties is revealed by microstructure characterization.

Effect of Different Coiling Temperature on Mechanical Properties in Hot Rolled TRIP Steel

2011 ◽  
Vol 239-242 ◽  
pp. 1092-1095
Author(s):  
Xu Tao Gao ◽  
Ai Min Zhao ◽  
Zheng Zhi Zhao ◽  
Ming Ming Zhang ◽  
Di Tang
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
X Ray Diffraction ◽  
Coiling Temperature ◽  
Experimental Steel ◽  
Transformation Induced Plasticity ◽  
X Ray ◽  
Trip Steels ◽  
Hot Rolled ◽  
Scanning Electron

By means of optical microscopy(OM), scanning electron microscopy(SEM),X-ray diffraction(XRD),And tensile test, Mechanical Properties of hot rolled transformation -induced plasticity (TRIP) steels which were prepared through three different coiling temperature was investigated. Result reveals that the formability index of the experimental steel descends when the coiling temperature becomes low. Different coiling temperature has greater impact on retained austenite. Amount and carbon content of retained austenite in the experimental steel get less with lower coiling temperature.

Isothermal Transformation, Microstructure and Mechanical Properties of Ausformed Low-Carbon Carbide-Free Bainitic Steel

2018 ◽  
Vol 941 ◽  
pp. 329-333 ◽  
Author(s):  
Jiang Ying Meng ◽  
Lei Jie Zhao ◽  
Fan Huang ◽  
Fu Cheng Zhang ◽  
Li He Qian
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Bainitic Ferrite ◽  
Isothermal Transformation ◽  
Bainitic Transformation ◽  
Isothermal Treatment ◽  
Bainitic Steel ◽  
Low Carbon ◽  
Microstructure And Mechanical Properties

In the present study, the effects of ausforming on the bainitic transformation, microstructure and mechanical properties of a low-carbon rich-silicon carbide-free bainitic steel have been investigated. Results show that prior ausforming shortens both the incubation period and finishing time of bainitic transformation during isothermal treatment at a temperature slightly above the Mspoint. The thicknesses of bainitic ferrite laths are reduced appreciably by ausforming; however, ausforming increases the amount of large blocks of retained austenite/martenisite and decreases the volume fraction of retained austenite. And accordingly, ausforming gives rise to significant increases in both yield and tensile strengths, but causes noticeable decreases in ductility and impact toughness.

Sign in / Sign up

Export Citation Format

Share Document