scholarly journals A step forward to a more efficient wastewater treatment by membrane surface modification via polymerizable bicontinuous microemulsion

2015 ◽  
Vol 482 ◽  
pp. 103-114 ◽  
Author(s):  
Francesco Galiano ◽  
Alberto Figoli ◽  
Shamim Ahmed Deowan ◽  
Daniel Johnson ◽  
Sacide Alsoy Altinkaya ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Surface Modification ◽  
Membrane Surface ◽  
Bicontinuous Microemulsion

scholarly journals Thermal Annealing Surface Modification: Effect on Surface and Performance of Electrospun Nylon 6,6 Nanofiber Membrane for Wastewater Treatment

2021 ◽  
Vol 5 (1) ◽  
pp. 56
Author(s):  
Muhammad Amir Nasrin Mohd Asri ◽  
Nur Syakinah Abd Halim ◽  
Mohd Dzul Hakim Wirzal ◽  
Abdull Rahim Mohd Yusoff ◽  
Muhammad Roil Bilad
Keyword(s):  
Wastewater Treatment ◽  
Surface Modification ◽  
Thermal Annealing ◽  
Membrane Surface ◽  
High Porosity ◽  
Nanofiber Membrane ◽  
Filtration Time ◽  
Nylon 6,6 ◽  
And Performance ◽  
Optimum Annealing Temperature

As the forefront in fiber materials development, electrospun nanofiber membrane (NFM) is potentially reliable for wastewater treatment due to its excellent properties for instance; large surface area, high porosity, tuneable pore size, and has great flux as compared to other conventional membranes. However, fouling issue will lead to degradation of membrane performance. Fouling issue can be alleviated by applying membrane surface modification. In this study, thermal annealing is applied onto nylon 6,6 nanofiber membrane with three different temperatures (60°C, 80°C and 120°C). Results show that annealing causes membrane shrinkage and reduction of membrane fiber diameter where the fiber reduced from 138.5 nm to 108.5 nm when annealed at 120°C. The optimum annealing temperature for the membrane was found to be at 60˚C as the membrane shows the highest flux at 1200 L/m2.h at 75 minutes filtration time and took longer time to get fouled (>75 minutes) compared with un-annealed membrane (55 minutes). Nylon 6,6 nanofiber membrane is also proven to give more than 90% of COD and turbidity rejection.

MEMBRANE SURFACE MODIFICATION AND BACKPULSING FOR WASTEWATER TREATMENT

2001 ◽  
Vol 36 (7) ◽  
pp. 1557-1573 ◽  
Author(s):  
Huimin Ma ◽  
David R. Nielsen ◽  
Christopher N. Bowman ◽  
Robert H. Davis
Keyword(s):  
Wastewater Treatment ◽  
Surface Modification ◽  
Membrane Surface

scholarly journals Tanning Wastewater Treatment by Ultrafiltration: Process Efficiency and Fouling Behavior

Membranes ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 461
Author(s):  
Fu Yang ◽  
Zhengkun Huang ◽  
Jun Huang ◽  
Chongde Wu ◽  
Rongqing Zhou ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Shear Rate ◽  
Membrane Surface ◽  
Filtration Efficiency ◽  
Operating Conditions ◽  
Process Efficiency ◽  
Transmembrane Pressure ◽  
Leather Industry ◽  
Pore Blocking ◽  
The Impact

Ultrafiltration is a promising, environment-friendly alternative to the current physicochemical-based tannery wastewater treatment. In this work, ultrafiltration was employed to treat the tanning wastewater as an upstream process of the Zero Liquid Discharge (ZLD) system in the leather industry. The filtration efficiency and fouling behaviors were analyzed to assess the impact of membrane material and operating conditions (shear rate on the membrane surface and transmembrane pressure). The models of resistance-in-series, fouling propensity, and pore blocking were used to provide a comprehensive analysis of such a process. The results show that the process efficiency is strongly dependent on the operating conditions, while the membranes of either PES or PVDF showed similar filtration performance and fouling behavior. Reversible resistance was the main obstacle for such process. Cake formation was the main pore blocking mechanism during such process, which was independent on the operating conditions and membrane materials. The increase in shear rate significantly increased the steady-state permeation flux, thus, the filtration efficiency was improved, which resulted from both the reduction in reversible resistance and the slow-down of fouling layer accumulate rate. This is the first time that the fouling behaviors of tanning wastewater ultrafiltration were comprehensively evaluated, thus providing crucial guidance for further scientific investigation and industrial application.

scholarly journals Rapid Surface Modification of Ultrafiltration Membranes for Enhanced Antifouling Properties

Membranes ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 401
Author(s):  
Noresah Said ◽  
Ying Siew Khoo ◽  
Woei Jye Lau ◽  
Mehmet Gürsoy ◽  
Mustafa Karaman ◽  
...  
Keyword(s):  
Surface Modification ◽  
Deposition Time ◽  
Plasma Deposition ◽  
Membrane Surface ◽  
Pure Water ◽  
Plasma Modification ◽  
Surface Hydrophilicity ◽  
Water Cleaning ◽  
Modification Method ◽  
Modified Membrane

In this work, several ultrafiltration (UF) membranes with enhanced antifouling properties were fabricated using a rapid and green surface modification method that was based on the plasma-enhanced chemical vapor deposition (PECVD). Two types of hydrophilic monomers—acrylic acid (AA) and 2-hydroxyethyl methacrylate (HEMA) were, respectively, deposited on the surface of a commercial UF membrane and the effects of plasma deposition time (i.e., 15 s, 30 s, 60 s, and 90 s) on the surface properties of the membrane were investigated. The modified membranes were then subjected to filtration using 2000 mg/L pepsin and bovine serum albumin (BSA) solutions as feed. Microscopic and spectroscopic analyses confirmed the successful deposition of AA and HEMA on the membrane surface and the decrease in water contact angle with increasing plasma deposition time strongly indicated the increase in surface hydrophilicity due to the considerable enrichment of the hydrophilic segment of AA and HEMA on the membrane surface. However, a prolonged plasma deposition time (>15 s) should be avoided as it led to the formation of a thicker coating layer that significantly reduced the membrane pure water flux with no significant change in the solute rejection rate. Upon 15-s plasma deposition, the AA-modified membrane recorded the pepsin and BSA rejections of 83.9% and 97.5%, respectively, while the HEMA-modified membrane rejected at least 98.5% for both pepsin and BSA. Compared to the control membrane, the AA-modified and HEMA-modified membranes also showed a lower degree of flux decline and better flux recovery rate (>90%), suggesting that the membrane antifouling properties were improved and most of the fouling was reversible and could be removed via simple water cleaning process. We demonstrated in this work that the PECVD technique is a promising surface modification method that could be employed to rapidly improve membrane surface hydrophilicity (15 s) for the enhanced protein purification process without using any organic solvent during the plasma modification process.

Submerged Ultrafiltration for Minimizing Energy Process of Refinery Wastewater Treatment

2013 ◽  
Vol 789 ◽  
pp. 531-537
Author(s):  
Erna Yuliawati ◽  
Ahmad Fauzi Ismail
Keyword(s):  
Wastewater Treatment ◽  
Polyvinylidene Fluoride ◽  
Membrane Surface ◽  
Suspended Solid ◽  
Hollow Fibers ◽  
Refinery Wastewater ◽  
Permeate Flux ◽  
Energy Process ◽  
Oil Refineries ◽  
And Performance

Refinery wastewater treatment is needed especially in the oil-producing arid regions such as oil refineries due to water scarcity. One of potentially applicable process to treat refinery wastewater is a submerged membrane technology. However, the application of submerged membrane systems for industrial wastewater treatment is still in its infancy due to significant variety in wastewater composition and high operational costs. Aim of this study was to investigate ultrafiltration (UF) membrane morphology and performance for refinery produced wastewater treatment. Submerged UF bundle was equipped using polyvinylidene fluoride (PVDF) hollow fibers, which added by dispersing lithium chloride monohydrate (LiCl.H2O) and titanium dioxide (TiO2). The comparison of morphological and performance tests was conducted on prepared PVDF ultrafiltration membranes. Distinctive changes were observed in membrane characteristics in term of membrane wettability, tensile testing and roughness measurement. Mean pore size and surface porosity were calculated based on permeate flux. Fouling characteristics for hydrophilic PVDF hollow fibers fouled with suspended solid matter was also investigated. Mixed liquor suspended solid (MLSS) of 3 g/L and 4.5 g/L were assessed by using submerged PVDF membrane with varied air bubble flow rates. Results showed that effect of air bubbles flow rate of 2.4 ml/min increased flux, total suspended solids (TSS) and sulfide removal of 148.82 L/m2h, 99.82 % and 89.2%, respectively due to increase of turbulence around fibers, which exerts shear stress to minimize particles deposited on membrane surface. It was concluded that submerged ultrafiltration is an available option to minimize energy process for treating such wastewater solution.

scholarly journals Diethylene Glycol-Assisted Organized TiO2 Nanostructures for Photocatalytic Wastewater Treatment Ceramic Membranes

Water ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 750 ◽  
Author(s):  
Ahmad ◽  
Kim ◽  
Kim ◽  
Kim
Keyword(s):  
Wastewater Treatment ◽  
Diethylene Glycol ◽  
Membrane Fouling ◽  
Ceramic Membrane ◽  
Membrane Surface ◽  
Ceramic Membranes ◽  
Tio2 Nanorods ◽  
Hydrolysis Rate ◽  
Capping Agent ◽  
Alumina Support

A high-performance photocatalytic ceramic membrane was developed by direct growth of a TiO2 structure on a macroporous alumina support using a hydrothermal method. The morphological nanostructure of TiO2 on the support was successfully controlled via the interaction between the TiO2 precursor and a capping agent, diethylene glycol (DEG). The growth of anatase TiO2 nanorods was observed both on the membrane surface and pore walls. The well-organized nanorods TiO2 reduced the perturbation of the alumina support, thus controlling the hydrolysis rate of the TiO2 precursor and reducing membrane fouling. However, a decrease in the amount of the DEG capping agent significantly reduced membrane permeability, owing to the formation of nonporous clusters of TiO2 on the support. Distribution of the organized TiO2 nanorods on the support was very effective for the improvement of the organic removal efficiency and antifouling under ultraviolet illumination. The TiO2 nanostructure associated with the reactive crystalline phase, rather than the amount of layered TiO2 formed on the support, which was found to be the key to controlling photocatalytic membrane reactivity. These experimental findings would provide a new approach for the development of efficacious photocatalytic membranes with improved performance for wastewater treatment.

Sign in / Sign up

Export Citation Format

Share Document