Enhanced wear resistance and new insight into microstructure evolution of in-situ (Ti,Nb)C reinforced 316 L stainless steel matrix prepared via laser cladding

2020 ◽  
Vol 128 ◽  
pp. 106043 ◽  
Author(s):  
Mingyang Zhang ◽  
Min Li ◽  
Shufeng Wang ◽  
Jing Chi ◽  
Liangshuai Ren ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Laser Cladding ◽  
Microstructure Evolution ◽  
Steel Matrix ◽  
316 L Stainless Steel ◽  
Insight Into

Fabrication of SiC Particulates Reinforced MoSi2 Composite Coating by Laser Cladding

2008 ◽  
Vol 373-374 ◽  
pp. 304-307
Author(s):  
Sen Yang ◽  
Ming Run Wang ◽  
Tao Gong ◽  
Wen Jin Liu
Keyword(s):  
Wear Resistance ◽  
Laser Cladding ◽  
Continuous Wave ◽  
Steel Substrate ◽  
Laser Output Power ◽  
Scanning Velocity ◽  
Sic Particulates ◽  
Metallurgical Bond ◽  
Improve Wear Resistance

In order to improve wear resistance of carbon steel, laser cladding experiments were carried out using a 3kW continuous wave CO2 laser. The diameter of the laser beam was 3-5mm, the scanning velocity was 3-10mm/s, and the laser output power was 1.0-1.3kW. The experimental results showed that MoSi2/SiCP composites coating could be in-situ synthesized from mixture powders of molybdenum, silicon and SiC by laser cladding. A good metallurgical bond between the coating and the substrate could be achieved. The microstructures of the coating were mainly composed of MoSi2, SiC and FeSiMo phases. The average microhardness of the coating was about HV0.21300, about 6.0 times larger than that of steel substrate.

scholarly journals Laser Cladding of Ni-Co-W Composite Coating on Stainless Steel to Enhance Wear Resistance

2021 ◽  
Author(s):  
Linlin ZHANG ◽  
Dawei ZHANG
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Composite Coating ◽  
Laser Cladding ◽  
Composite Coatings ◽  
Eutectic Structure ◽  
Wear Properties ◽  
Fine Grained ◽  
Noticeable Improvement ◽  
Enhance Wear Resistance

Ni-Co-W composite coatings modified by different contents of Co-based alloy powder in the Ni-based alloy with 35 wt.% WC (Ni35WC) were deposited on stainless steel by laser cladding. The influence of compositional and microstructural modification on the wear properties has been comparatively investigated by XRD, SEM, and EDS techniques. It was found that the austenite dendrites in the modified coating adding 50 wt.% Co-based alloy were refined and a lot of Cr23C6 or M23(C, B)6 compounds with fine lamellar feature were formed around austenitic grain boundaries or in the intergranular regions. The contribution of element Co to the modification of Ni35WC coating is that it cannot only promote the formation of more hard compounds to refine austenite grains, but also refine the size of precipitates, and change the phase type of eutectic structure as a result of disappeared Cr boride brittle phases. A noticeable improvement in wear resistance is obtained in the Ni35WC coating with 50 wt.% Co-based alloy, which makes the wear rate decreased by about 53 % and 30% by comparison to that of the substrate and the Ni35WC coating, respectively. It is suggested that the improvement is closely related to the composite coating being strengthened owing to the increase of coating hardness, formation of a fine-grained microstructure caused by Co, and fine hard precipitate phases in the eutectic structure.

scholarly journals A Comparative Study on the Tribological Properties of a Cobalt-Free Superaustenitic Stainless Steel at Elevated Temperature

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1123
Author(s):  
Frederic van gen Hassend ◽  
Sebastian Weber
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Elevated Temperature ◽  
Superaustenitic Stainless Steel ◽  
Material Loss ◽  
Hardness Tests ◽  
Alternative Material ◽  
Wear Tests ◽  
Hot Hardness

The properties of a cobalt-free cast superaustenitic stainless steel (SASS) is investigated comparatively to the commercial high-cobalt alloyed GX15CrNiCo21-20-20 (1.4957, N-155) steel regarding its global hardness and wear resistance at elevated temperature by means of in situ hot hardness tests and cyclic abrasive sliding wear tests against an Al2O3 (corundum) counter-body at 600 °C. In the aged condition, results show that the 1.4957 steel suffers a higher material loss due to brittle failure initiated by coarse eutectic Cr-rich carbides which are incorporated into a mechanically mixed layer during abrasive loading. In contrast, within the Co-free steel eutectic M6(C,N) carbonitrides are distributed more homogeneously showing less tendency to form network structures. Due to the combination of primary Nb-rich globular-blocky MX-type carbonitrides and eutectic M6(C,N) carbonitrides dispersed within an Laves phase strengthened austenitic matrix, this steel provides comparable hardness and significantly improved wear resistance at elevated temperature. Thus, it may be an adequate alternative material to commercial SASS and offers the possibility to save cobalt for future applications.

Sign in / Sign up

Export Citation Format

Share Document