Nickel doped cobaltite spinel as a solar selective absorber coating for efficient photothermal conversion with a low thermal radiative loss at high operating temperatures

2019 ◽  
Vol 200 ◽  
pp. 109917 ◽  
Author(s):  
S.R. Atchuta ◽  
S. Sakthivel ◽  
Harish C. Barshilia
2020 ◽  
pp. 40-45
Author(s):  
Nadezhda O. Vzduleva ◽  
Valery B. Gitlin

The problems of ensuring the stability of the temperature of the chromatographic experiment carried out using a serial gas chromatograph LGH-3000 are considered. Limiting the permissible heating rate of the chromatograph thermostats does not allow a quick transition to the new conditions of the chromatographic experiment in accordance with the requirements of the technical conditions. The processes of heating and cooling the thermostat are analyzed. It is shown that the ratio of the duration of the interval equal to the sum of the durations of the heating and cooling intervals to the duration of the heating interval is inversely proportional to the temperature of the chromatographic experiment. Based on this situation, an empirical algorithm is proposed for heating the thermostat to a given temperature, which made it possible to reduce the time it takes to reach a given temperature in the entire range of operating temperatures.


2005 ◽  
Vol 33 (3) ◽  
pp. 156-178 ◽  
Author(s):  
T. J. LaClair ◽  
C. Zarak

Abstract Operating temperature is critical to the endurance life of a tire. Fundamental differences between operations of a tire on a flat surface, as experienced in normal highway use, and on a cylindrical test drum may result in a substantially higher tire temperature in the latter case. Nonetheless, cylindrical road wheels are widely used in the industry for tire endurance testing. This paper discusses the important effects of surface curvature on truck tire endurance testing and highlights the impact that curvature has on tire operating temperature. Temperature measurements made during testing on flat and curved surfaces under a range of load, pressure and speed conditions are presented. New tires and re-treaded tires of the same casing construction were evaluated to determine the effect that the tread rubber and pattern have on operating temperatures on the flat and curved test surfaces. The results of this study are used to suggest conditions on a road wheel that provide highway-equivalent operating conditions for truck tire endurance testing.


Alloy Digest ◽  
1992 ◽  
Vol 41 (9) ◽  

Abstract Aluchrom O, Aluchrom I, Aluchrom S and Aluchrom W are ferritic stainless alloys of high resistance to oxidation at high operating temperatures with a range of resistivity values. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. Filing Code: SS-534. Producer or source: VDM Technologies Corporation.


Alloy Digest ◽  
1954 ◽  
Vol 3 (10) ◽  

Abstract SENECA is a tungsten-chromium type of hot work steel having good red hardness and resistance to abrasion. It will withstand high operating temperatures up to 1000 deg. F for long periods. It is a SAE type IV F-2 alloy. This datasheet provides information on composition and hardness as well as fracture toughness. It also includes information on forming, heat treating, and machining. Filing Code: TS-25. Producer or source: Atlas Steels Company.


Alloy Digest ◽  
2017 ◽  
Vol 66 (12) ◽  

Abstract NITRODUR 8524 (8CrMo16, 1.8524) is one of the Nitrodur family of nitriding steels that are used where high surface hardness and good fatigue strength are required and the material is also subjected to high temperatures. Nitrided surfaces maintain their hardness and strength at operating temperatures of up to approximately 500–550 deg C (932–1022 deg F). This datasheet provides information on composition, hardness, and tensile properties as well as fracture toughness. It also includes information on surface qualities as well as casting and forming. Filing Code: SA-807. Producer or source: Schmolz + Bickenbach Group.


Alloy Digest ◽  
2000 ◽  
Vol 49 (1) ◽  

Abstract Finkl WF-XTRA has high wear resistance while retaining moderate fracture toughness. The alloy is recommended for larger die blocks. The optimum diameter for hardenability is 838 mm (33 in.). It is appropriate for use in high-production hammers where die temperatures may be above average or in presses with moderately high operating temperatures. This datasheet provides information on composition, microstructure, hardness, and tensile properties as well as fracture toughness. It also includes information on heat treating, machining, and joining. Filing Code: TS-570. Producer or source: A. Finkl & Sons Company.


1987 ◽  
Vol 33 (114) ◽  
pp. 239-242
Author(s):  
M. E. R. Walford

AbstractWe discuss the suggestion that small underwater transmitters might be used to illuminate the interior of major englacial water channels with radio waves. Once launched, the radio waves would naturally tend to be guided along the channels until attenuated by absorption and by radiative loss. Receivers placed within the channels or at the glacier surface could be used to detect the signals. They would provide valuable information about the connectivity of the water system. The electrical conductivity of the water is of crucial importance. A surface stream on Storglaciären, in Sweden, was found, using a low-frequency technique, to have a conductivity of approximately 4 × 10−4 S m−1. Although this is several hundred times higher than the conductivity of the surrounding glacier ice, the contrast is not sufficient to permit us simply to use electrical conductivity measurements to establish the connectivity of englacial water channels. However, the water conductivity is sufficiently small that, under favourable circumstances, radio signals should be detectable after travelling as much as a few hundred metres along an englacial water channel. In a preliminary field experiment, we demonstrated semi quantitatively that radio waves do indeed propagate as expected, at least in surface streams. We conclude that under-water radio transmitters could be of real practical value in the study of the englacial water system, provided that sufficiently robust devices can be constructed. In a subglacial channel, however, we expect the radio range would be much smaller, the environment much harsher, and the technique of less practical value.


Sign in / Sign up

Export Citation Format

Share Document