scholarly journals Modeling of three-dimensional exciplex pumped fluid Cs vapor laser with transverse and longitudinal gas flow

2021 ◽  
Vol 9 ◽  
Author(s):  
Chenyi Su ◽  
Xingqi Xu ◽  
Jinghua Huang ◽  
Bailiang Pan
Keyword(s):  
Wall Temperature ◽  
Laser Power ◽  
Gas Flow ◽  
Particle Density ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Heat Accumulation ◽  
Vapor Laser ◽  
Output Laser Power ◽  
Output Laser

Abstract Considering the thermodynamical fluid mechanics in the gain medium and laser kinetic processes, a three-dimensional theoretical model of an exciplex-pumped Cs vapor laser with longitudinal and transverse gas flow is established. The slope efficiency of laser calculated by the model shows good agreement with the experimental data. The comprehensive three-dimensional distribution of temperature and particle density of Cs is depicted. The influence of pump intensity, wall temperature, and fluid velocity on the laser output performance is also simulated and analyzed in detail, suggesting that a higher wall temperature can guarantee a higher output laser power while causing a more significant heat accumulation in the cell. Compared with longitudinal gas flow, the transverse flow can improve the output laser power by effectively removing the generated heat accumulation and alleviating the temperature gradient in the cell.

Effects of Heat Accumulation on Temperature Field during Multi-Track Laser Cladding of Preset MCrAlY Coating

2021 ◽  
Vol 1020 ◽  
pp. 157-163
Author(s):  
Dong Sheng Wang ◽  
Hao Yang ◽  
Li Ye Yue ◽  
Pei Pei Zhang
Keyword(s):  
Temperature Field ◽  
Laser Cladding ◽  
Laser Power ◽  
Laser Scanning ◽  
Three Dimensional ◽  
Scanning Speed ◽  
Element Model ◽  
Heat Accumulation ◽  
Loop Control ◽  
Mcraly Coating

To investigate influences of multi-track overlapping on melting of preset MCrAlY coating during laser cladding plasma spraying, a three-dimensional finite element model of the continuously moving temperature field during multi-track laser cladding was constructed using the ANSYS parametric design language (APDL) based on the existing temperature field model during single-track laser cladding. According to analysis results of temperature field, temperature of samples increases gradually during laser cladding due to heat accumulation effect of laser scanning, and the molten pool expands gradually. There are evident differences among different scanning pathways. Therefore, it is impossible to get high-quality cladding coating with uniform melting and small dilution ratio. Molten pools with basically same sizes in different scanning pathways can be gained by decreasing laser power or increasing scanning speed in different tracks one by one. Similarly, differences of molten pools in different scanning pathways can be relieved effectively through preheating of samples. Through a closed-loop control over the highest cladding temperature, a more even cladding coating can be gained through adaptive control of laser power and / or scanning speed.

scholarly journals Microchip Nd:YAG and Nd:YVO4 Lasers Pumped by VHG Wavelength-Stabilized Laser Diode

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
T. Saiki ◽  
A. Tatebayashi
Keyword(s):  
Laser Diode ◽  
Laser Power ◽  
Low Cost ◽  
Single Mode ◽  
Microchip Laser ◽  
Optical Conversion Efficiency ◽  
Output Laser Power ◽  
Cw Operation ◽  
The Difference ◽  
Output Laser

We adopted a single-mode, single-wavelength volume holographic grating (VHG) wavelength-stabilized wavelength laser diode (LD) as a pumping LD for an end-pumped microchip Nd:YAG and Nd:YVO4 lasers we developed during CW and pulse operations. Higher optical-optical and slope efficiencies during CW operation have been obtained than when using a VHG LD experimentally. Output laser power is insensitive to the temperature of the LD when using a wavelength-stabilized LD and can remain stable and almost constant until the temperature of LD increases up to 40°C. The improved optical-optical conversion efficiency of 58% for the Nd:YVO4 laser has been obtained and calculated the output laser power during CW operation and compared it with the experimental results. We found that the output laser power of the Nd:YVO4 laser using the VHG wavelength-stabilized LD was more than twice as high as that using an LD without VHG. When the ambient temperature increases, the difference in output laser power should be large. In the future, a low-cost end-pumped microchip laser that does not require a temperature control should be developed.

Investigating thermal developing zone of compressible laminar flow inside hot tube

2019 ◽  
Vol 16 (3) ◽  
pp. 581-594
Author(s):  
Bahador Abolpour ◽  
Rahim Shamsoddini
Keyword(s):  
Heat Transfer ◽  
Gas Flow ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Volumetric Flow Rate ◽  
Reynolds Stress Model ◽  
Navier Stokes ◽  
Turbulent Model ◽  
Content Type ◽  
Energy Equations

Purpose Increasing the temperature of gas flows passing through hot tubes is one of the industrial interests. Operations in the gas phase with high temperature variations involve engineers with the compressible fluids problems. The paper aims to discuss this issue. Design/methodology/approach In this study, a mathematical three-dimensional turbulent model is applied for investigating the heat transfer and laminar gas flow inside the thermal developing zone of a hot tube. The Favre Averaged Navier–Stokes and energy equations and also the Reynolds Stress Model are numerically solved to obtain the fluid velocity and temperature profiles inside this the tube. This model is validated using the experimental data and also well-known formulas in this science. Findings Finally, effects of inlet volumetric flow rate, heating conditions of the tube wall and tube angle on the temperature and velocity distributions of the gaseous phase inside this zone are investigated. Originality/value The compressible laminar gas flow and also heat transfer in the thermal developing zone of a hot tube is studied using a three-dimensional turbulent model.

Real gas flow fields about three dimensional configurations

1983 ◽  
Author(s):  
A. BALAKRISHNAN ◽  
C. LOMBARD ◽  
W.C. DAVY
Keyword(s):  
Gas Flow ◽  
Three Dimensional ◽  
Flow Fields ◽  
Real Gas

scholarly journals Parameters Optimization of Auxiliary Gas Process for Double-Wire SS316L Stainless Steel Arc Additive Manufacturing

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 190
Author(s):  
Wei Wu ◽  
Jiaxiang Xue ◽  
Wei Xu ◽  
Hongyan Lin ◽  
Heqing Tang ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Additive Manufacturing ◽  
Process Parameters ◽  
Evaluation System ◽  
Gas Flow ◽  
Interactive Effect ◽  
Parameters Optimization ◽  
Heat Accumulation ◽  
Auxiliary Process ◽  
Strength And Stiffness

Serious heat accumulation limits the further efficiency and application in additive manufacturing (AM). This study accordingly proposed a double-wire SS316L stainless steel arc AM with a two-direction auxiliary gas process to research the effect of three parameters, such as auxiliary gas nozzle angle, auxiliary gas flow rate and nozzle-to-substrate distance on depositions, then based on the Box–Behnken Design response surface, a regression equation between three parameters and the total score were established to optimized parameters by an evaluation system. The results showed that samples with nozzle angle of 30° had poor morphology but good properties, and increasing gas flow or decreasing distance would enhance the airflow strength and stiffness, then strongly stir the molten pool and resist the interference. Then a diverse combination of auxiliary process parameters had different influences on the morphology and properties, and an interactive effect on the comprehensive score. Ultimately the optimal auxiliary gas process parameters were 17.4°, 25 L/min and 10.44 mm, which not only bettered the morphology, but refined the grains and improved the properties due to the stirring and cooling effect of the auxiliary gas, which provides a feasible way for quality and efficiency improvements in arc additive manufacturing.

scholarly journals Strategies to Reduce Porosity in Al-Mg WAAM Parts and Their Impact on Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 524
Author(s):  
Maider Arana ◽  
Eneko Ukar ◽  
Iker Rodriguez ◽  
Amaia Iturrioz ◽  
Pedro Alvarez
Keyword(s):  
Mechanical Properties ◽  
Gas Flow ◽  
Bottom Layer ◽  
Local Heat ◽  
High Porosity ◽  
Shielding Gas ◽  
Heat Accumulation ◽  
High Mechanical Property ◽  
Building Conditions ◽  
Static Tensile

With the advent of disruptive additive manufacturing (AM), there is an increasing interest and demand of high mechanical property aluminium parts built directly by these technologies. This has led to the need for continuous improvement of AM technologies and processes to obtain the best properties in aluminium samples and develop new alloys. This study has demonstrated that porosity can be reduced below 0.035% in area in Al-Mg samples manufactured by CMT-based WAAM with commercial filler metal wires by selecting the correct shielding gas, gas flow rate, and deposition strategy (hatching or circling). Three phase Ar+O2+N2O mixtures (Stargold®) are favourable when the hatching deposition strategy is applied leading to wall thickness around 6 mm. The application of circling strategy (torch movement with overlapped circles along the welding direction) enables the even build-up of layers with slightly thicker thickness (8 mm). In this case, Ar shielding gas can effectively reduce porosity if proper flow is provided through the torch. Reduced gas flows (lower than 30 Lmin) enhance porosity, especially in long tracks (longer than 90 mm) due to local heat accumulation. Surprisingly, rather high porosity levels (up to 2.86 area %) obtained in the worst conditions, had a reduced impact on the static tensile test mechanical properties, and yield stress over 110 MPa, tensile strength over 270 MPa, and elongation larger than 27% were achieved either for Ar circling, Ar hatching, or Stargold® hatching building conditions. In all cases anisotropy was lower than 11%, and this was reduced to 9% for the most appropriate shielding conditions. Current results show that due to the selected layer height and deposition parameters there was a complete re-melting of the previous layer and a thermal treatment on the prior bottom layer that refined the grain size removing the original dendritic and elongated structure. Under these conditions, the minimum reported anisotropy levels can be achieved.

scholarly journals Effect of buried depth on thermal performance of a vertical U-tube underground heat exchanger

Open Physics ◽  
2021 ◽  
Vol 19 (1) ◽  
pp. 327-330
Author(s):  
Li Yang ◽  
Bo Zhang ◽  
Jiří Jaromír Klemeš ◽  
Jie Liu ◽  
Meiyu Song ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Simplified Model ◽  
Two Dimensional ◽  
Construction Sites ◽  
Full Size ◽  
Unit Depth ◽  
Research Show

Abstract Many researchers numerically investigated U-tube underground heat exchanger using a two-dimensional simplified pipe. However, a simplified model results in large errors compared to the data from construction sites. This research is carried out using a three-dimensional full-size model. A model validation is conducted by comparing with experimental data in summer. This article investigates the effects of fluid velocity and buried depth on the heat exchange rate in a vertical U-tube underground heat exchanger based on fluid–structure coupled simulations. Compared with the results at a flow rate of 0.4 m/s, the results of this research show that the heat transfer per buried depth at 1.0 m/s increases by 123.34%. With the increase of the buried depth from 80 to 140 m, the heat transfer per unit depth decreases by 9.72%.

scholarly journals Modelling of Applied Magnetic Field and Thermal Radiations Due to the Stretching of Cylinder

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1077
Author(s):  
Muhammad Tamoor ◽  
Muhammad Kamran ◽  
Sadique Rehman ◽  
Aamir Farooq ◽  
Rewayat Khan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Numerical Approach ◽  
Skin Friction Coefficient ◽  
Physical Parameters ◽  
Boundary Layer Equations ◽  
Convective Parameter ◽  
Momentum And Heat Transfer ◽  
Dimensional Boundary

In this study, a numerical approach was adopted in order to explore the analysis of magneto fluid in the presence of thermal radiation combined with mixed convective and slip conditions. Using the similarity transformation, the axisymmetric three-dimensional boundary layer equations were reduced to a self-similar form. The shooting technique, combined with the Range–Kutta–Fehlberg method, was used to solve the resulting coupled nonlinear momentum and heat transfer equations numerically. When physically interpreting the data, some important observations were made. The novelty of the present study lies in finding help to control the rate of heat transfer and fluid velocity in any industrial manufacturing processes (such as the cooling of metallic plates). The numerical results revealed that the Nusselt number decrease for larger Prandtl number, curvature, and convective parameters. At the same time, the skin friction coefficient was enhanced with an increase in both slip velocity and convective parameter. The effect of emerging physical parameters on velocity and temperature profiles for a nonlinear stretching cylinder has been thoroughly studied and analyzed using plotted graphs and tables.

Sign in / Sign up

Export Citation Format

Share Document