Dynamics and Control of Single-Line Kites

2006 ◽  
Vol 110 (1111) ◽  
pp. 615-621 ◽  
Author(s):  
G. Sánchez
Keyword(s):  
Wind Velocity ◽  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
Open Loop ◽  
Single Line ◽  
Atmospheric Conditions ◽  
Loop Control ◽  
Loop Control System ◽  
Dynamics And Control ◽  
The Stability

Abstract This paper presents a dynamic analysis of a single-line kite with two degrees of freedom. A Lagrangian formulation is used to write convenient equations of motion. The equilibrium states of the system and their stability are studied; Eigenvalues and eigenmodes are calculated by using linear theory. The stability in the parametric plane δ – W0 is discussed, where δ defines the bridle geometry and W0 is wind velocity. The system goes through a Hopf bifurcation and periodic branches of solutions appear. The orbits and their stability have been calculated numerically using Floquet theory and wind velocity seems to play an important role in their existence. Finally the kite response against gusts is considered and an open loop control system developed to keep the flight altitude invariant under changing atmospheric conditions. Modifying the bridle’s geometry seems to be a convenient way to control a kite’s performance.

scholarly journals The research of the pulse oxygen supply based on the fuzzy control technology

2018 ◽  
Vol 189 ◽  
pp. 06012
Author(s):  
Faling Hu ◽  
Tongfeng Niu ◽  
Jun Yao ◽  
Bingyan Cui ◽  
Haoxing Xu ◽  
...  
Keyword(s):  
Control System ◽  
Fuzzy Control ◽  
Open Loop ◽  
Open Loop Control ◽  
Loop Control ◽  
Fuzzy Control System ◽  
Loop Control System ◽  
Working Principle ◽  
The Stability ◽  
Close Loop Control

According to the working principle of pulse oxygen supplies, we analyze how to realize the control of the oxygen flow by double different valves. a two-dimensional fuzzy control system is proposed to solve the unstable problem, which is brought by the shortcomings of the open-loop control system. We add a new parameter, the rate of the differential pressure signal changes, which contributes to a close –loop control system and increases the stability of the system. The experiments and the data show that the fuzzy control system make the process of breathing much more comfortable and solve the hysteresis and overshoot caused by the open-loop control system. The product reliability has been greatly improved.

scholarly journals Design of Non-Inverting Buck-Boost Converter for Electronic Ballast Compatible with LED Drivers

2018 ◽  
pp. 473-481
Keyword(s):  
Low Cost ◽  
Boost Converter ◽  
Open Loop ◽  
Loop Control ◽  
Electronic Ballast ◽  
Voltage Controller ◽  
Loop Control System ◽  
And Performance ◽  
The Stability ◽  
Led Drivers

This paper presents design and control of dual-switch non-inverting buck-boost converter (CBB). This converter is designed to simplify the compatibility of electronic ballast with simple and low cost LED drivers. The converter provides starting voltage and current limitation of electronic ballasts, which operates at continuous conduction mode (C.C.M.). The voltage of load terminal is controlled by adjusting the duty cycle of the PWM regulator. Although both converter switches are controlled separately, one feedback control loop is needed to obtain the desired compensator level. Appropriate control requirements have been defined by analyzing open-loop characteristic of converter transfer function through the small-signal model of CBB, which lets decide about the control strategy and analyse the stability and performance of the closed loop control system. In order to obtain the desired output voltage, Type-III rational controller is preferred because of the non-minimum phase feature in the converter boost mode. The performance of the synthesized voltage controller is verified by comparing of the pre-determined performance requirements and the obtained simulation results.

Responses and Optimization of a PID-Based Speed Regulating System of the Planetary Mixer

2011 ◽  
Vol 418-420 ◽  
pp. 1865-1868
Author(s):  
Ming Jin Yang ◽  
Xi Wen Li ◽  
Zhi Gang Wang ◽  
Tie Lin Shi
Keyword(s):  
Control System ◽  
Open Loop ◽  
Open Loop Control ◽  
Efficient Operation ◽  
Loop Control ◽  
Loop Control System ◽  
Response Optimization ◽  
Close Loop Control ◽  
Close Loop Control System

The performance of speed regulating is very important to the mixing process with safe, efficient operation and high quality of production. Strategies and practices of responses and optimization of a PID-based speed regulating system of a planetary mixer were presented in this paper. Research results show that: by means of the signal constraint function presented by Simulink Response Optimization, optimization PID parameters of the 2-DOF-PID controller can be obtained, and the response of close-loop control system has quite good performance of overshoot, response time, and stability compared with an open-loop control system.

Controlled Freezing of Nonideal Solutions With Application to Cryosurgical Processes

1991 ◽  
Vol 113 (4) ◽  
pp. 430-437 ◽  
Author(s):  
H. M. Budman ◽  
J. Dayan ◽  
A. Shitzer
Keyword(s):  
Cooling Rate ◽  
Freezing Process ◽  
Data Sets ◽  
Tracking Accuracy ◽  
Loop Control ◽  
Set Point ◽  
New Device ◽  
Loop Control System ◽  
The Stability ◽  
Controlled Freezing

Success of a cryosurgical procedure, i.e., maximal cell destruction, requires that the cooling rate be controlled during the freezing process. Standard cryosurgical devices are not usually designed to perform the required controlled process. In this study, a new cryosurgical device was developed which facilitates the achievement of a specified cooling rate during freezing by accurately controlling the probe temperature variation with time. The new device has been experimentally tested by applying it to an aqueous solution of mashed potatoes. The temperature field in the freezing medium, whose thermal properties are similar to those of biological tissue, was measured. The cryoprobe temperature was controlled according to a desired time varying profile which was assumed to maximize necrosis. The tracking accuracy and the stability of the closed loop control system were investigated. It was found that for most of the time the tracking accuracy was excellent and the error between the measured probe temperature and the desired set point is within ±0.4°C. However, noticeable deviations from the set point occurred due to the supercooling phenomenon or due to the instability of the liquid nitrogen boiling regime in the cryoprobe. The experimental results were compared to those obtained by a finite elements program and very good agreement was obtained. The deviation between the two data sets seems to be mainly due to errors in positioning of the thermocouple junctions in the medium.

scholarly journals Human-Robot Interaction with Robust Prediction of Movement Intention Surpasses Manual Control

2020 ◽  
Author(s):  
Sebastijan Veselic ◽  
Claudio Zito ◽  
Dario Farina
Keyword(s):  
Degrees Of Freedom ◽  
Linear Time ◽  
Open Loop ◽  
Human Robot Interaction ◽  
Manual Control ◽  
Reach To Grasp ◽  
Robot Interaction ◽  
Loop Control ◽  
User Awareness ◽  
Improving Accuracy

Designing robotic assistance devices for manipulation tasks is challenging. This work aims at improving accuracy and usability of physical human-robot interaction (pHRI) where a user interacts with a physical robotic device (e.g., a human operated manipulator or exoskeleton) by transmitting signals which need to be interpreted by the machine. Typically these signals are used as an open-loop control, but this approach has several limitations such as low take-up and high cognitive burden for the user. In contrast, a control framework is proposed that can respond robustly and efficiently to intentions of a user by reacting proactively to their commands. The key insight is to include context- and user-awareness in the controller, improving decision making on how to assist the user. Context-awareness is achieved by creating a set of candidate grasp targets and reach-to grasp trajectories in a cluttered scene. User-awareness is implemented as a linear time-variant feedback controller (TV-LQR) over the generated trajectories to facilitate the motion towards the most likely intention of a user. The system also dynamically recovers from incorrect predictions. Experimental results in a virtual environment of two degrees of freedom control show the capability of this approach to outperform manual control. By robustly predicting the user’s intention, the proposed controller allows the subject to achieve superhuman performance in terms of accuracy and thereby usability.

DESIGN OF ROBUST STATE FEEDBACK CONTROLLERS FOR REHABILITATION IN PARKINSONS TREMOR: A SIMULATION STUDY WITH UNCERTAIN MODEL OF BASAL GANGLIA

2016 ◽  
Vol 28 (04) ◽  
pp. 1650026
Author(s):  
K. Rouhollahi ◽  
M. Emadi Andani ◽  
S. M. Karbassi ◽  
M. Mojiri
Keyword(s):  
Basal Ganglia ◽  
State Feedback ◽  
Health Condition ◽  
Open Loop ◽  
The Other ◽  
Pole Placement ◽  
Neurosurgical Procedures ◽  
Loop Control ◽  
Disease Condition ◽  
Loop Control System

Deep brain stimulation (DBS) is one of the most effective neurosurgical procedures to reduce Parkinsons tremor. The conventional method of DBS is open loop stimulation of one area of basal ganglia (BG). On the other hand, existing feedback causes the reduction of additional stimulatory signal delivered to the brain which results in the reduction of the side effects caused by the excessive stimulation intensity. Actually, the stimulatory intensity of the controllers is reduced proportionally by the reduction of hands tremor, which is in fact the intended rehabilitation of the disease. The meaningful objective of this study is to design an architecture of controllers to decrease three criteria. The first one is the hand’s tremor, the second one is the level of delivered stimulation signal to brain in disease condition and the third one is the ratio of the level of delivered stimulation signal in health condition to disease condition. In order to achieve these objectives, a new architecture of a closed loop control system to stimulate two areas of BG at the same time is presented. One area (STN: subthalamic nucleus) is stimulated with a state feedback (SF) controller (pole placement method) and the other area (GPi: globus pallidus internal) is stimulated with a partial state feedback controller (PSFC). Considering these criteria, the results illustrate that stimulating two areas leads to a suitable performance. Simulation results show that the PSF and SF controllers are robust enough to the variations of the system parameters. Moreover, we are able to estimate the parameters of BG model in real time; it is a valuable method to update the time variable parameters of this model.

Modeling of Multibody Flexible Articulated Structures With Mutually Coupled Motions: Part II — Application and Results

1992 ◽  
Author(s):  
Jiechi Xu ◽  
Joseph R. Baumgarten
Keyword(s):  
Experimental Data ◽  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
Open Loop ◽  
Body Motion ◽  
Universal Joint ◽  
Open Loop System ◽  
Numerical Examples ◽  
Kinematic Properties ◽  
Good Agreement

Abstract The application of the systematic procedures in the derivation of the equations of motion proposed in Part I of this work is demonstrated and implemented in detail. The equations of motion for each subsystem are derived individually and are assembled under the concept of compatibility between the local kinematic properties of the elastic degrees of freedom of those connected elastic members. The specific structure under consideration is characterized as an open loop system with spherical unconstrained chains being capable of rotating about a Hooke’s or universal joint. The rigid body motion, due to two unknown rotations, and the elastic degrees of freedom are mutually coupled and influence each other. The traditional motion superposition approach is no longer applicable herein. Numerical examples for several cases are presented. These simulations are compared with the experimental data and good agreement is indicated.

An Integrated Design for a CNC Machine

2014 ◽  
pp. 254-265
Author(s):  
Amro Shafik ◽  
Salah Haridy
Keyword(s):  
Low Cost ◽  
Integrated Design ◽  
Numerical Data ◽  
Open Loop ◽  
Numerical Control ◽  
Future Research ◽  
Cnc Machine ◽  
Loop Control ◽  
Loop Control System ◽  
Stepper Motors

Computer Numerical Control (CNC) is a technology that converts coded instructions and numerical data into sequential actions that describe the motion of machine axes or the behavior of an end effector. Nowadays, CNC technology has been introduced to different stages of production, such as rapid prototyping, machining and finishing processes, testing, packaging, and warehousing. The main objective of this chapter is to introduce a methodology for design and implementation of a simple and low-cost educational CNC prototype. The machine consists of three independent axes driven by stepper motors through an open-loop control system. Output pulses from the parallel port of Personal Computer (PC) are used to drive the stepper motors after processing by an interface card. A flexible, responsive, and real-time Visual C# program is developed to control the motion of the machine axes. The integrated design proposed in this chapter can provide engineers and students in academic institutions with a simple foundation to efficiently build a CNC machine based on the available resources. Moreover, the proposed prototype can be used for educational purposes, demonstrations, and future research.

Active Damping of Vibrations of a Cantilever Beam by Axial Force Control

2007 ◽  
Author(s):  
Thomas Pumho¨ssel ◽  
Horst Ecker
Keyword(s):  
Cantilever Beam ◽  
Equations Of Motion ◽  
Beam Theory ◽  
Open Loop ◽  
Active Damping ◽  
Nonlinear Feedback ◽  
Euler Beam ◽  
Bending Vibrations ◽  
Loop Control ◽  
Damping Of Vibrations

In several fields, e.g. aerospace applications, robotics or the bladings of turbomachinery, the active damping of vibrations of slender beams which are subject to free bending vibrations becomes more and more important. In this contribution a slender cantilever beam loaded with a controlled force at its tip, which always points to the clamping point of the beam, is treated. The equations of motion are obtained using the Bernoulli-Euler beam theory and d’Alemberts principle. To introduce artificial damping to the lateral vibrations of the beam, the force at the tip of the beam has to be controlled in a proper way. Two different methods are compared. One concept is the closed-loop control of the force. In this case a nonlinear feedback control law is used, based on axial velocity feedback of the tip of the beam and a state-dependent amplification. By contrast, the concept of open-loop parametric control works without any feedback of the actual vibrations of the mechanical structure. This approach applies the force as harmonic function of time with constant amplitude and frequency. Numerical results are carried out to compare and to demonstrate the effectiveness of both methods.

Modeling of a Hydraulic Elevator Driven by an Open-Loop Control

2009 ◽  
Author(s):  
Roberto Strada ◽  
Alberto Oldani
Keyword(s):  
Power Generation ◽  
Closed Loop ◽  
Open Loop ◽  
The Other ◽  
Open Loop Control ◽  
Proportional Valve ◽  
Loop Control ◽  
Complete Knowledge ◽  
Motion Time ◽  
Loop Control System

Electro-hydraulic elevators are widely used systems, especially in low level buildings, due to their very good ratio between power generation and dynamic response. Generally, the goal of an elevator system is just to reach the floor with a precision enough to be comfortable for the passengers, without the need to follow a specific law of motion; hence an open-loop control system could be enough. Otherwise such a kind of solution reduces the number of components, bringing down the costs of production. On the other hand a complete knowledge of the mechanical system’s behaviour is required. In this work we deal with the analysis of the behaviour of a commercial hydraulic elevator driven by an open loop control that monitors the downstream pressure of the proportional valve supplying the cylinder. At the end of the paper, a closed loop solution based on the pressure measurement and on the motion time is proposed.

Sign in / Sign up

Export Citation Format

Share Document