Experimental results for the transpired turbulent boundary layer in an adverse pressure gradient

1975 ◽  
Vol 69 (2) ◽  
pp. 353-375 ◽  
Author(s):  
P. S. Andersen ◽  
W. M. Kays ◽  
R. J. Moffat
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layer Equation ◽  
Adverse Pressure Gradient ◽  
Stream Velocity ◽  
Pressure Gradients ◽  
Mean Velocity ◽  
Displacement Thickness

An experimental investigation of the fluid mechanics of the transpired turbulent boundary layer in zero and adverse pressure gradients was carried out on the Stanford Heat and Mass Transfer Apparatus. Profiles of (a) the mean velocity, (b) the intensities of the three components of the turbulent velocity fluctuations and (c) the Reynolds stress were obtained by hot-wire anemometry. The wall shear stress was measured by using an integrated form of the boundary-layer equation to ‘extrapolate’ the measured shear-stress profiles to the wall.The two experimental adverse pressure gradients corresponded to free-stream velocity distributions of the type u∞ ∞ xm, where m = −0·15 and −0·20, x being the streamwise co-ordinate. Equilibrium boundary layers (i.e. flows with velocity defect profile similarity) were obtained when the transpiration velocity v0 was varied such that the blowing parameter B = pv0u∞/τ0 and the Clauser pressure-gradient parameter $\beta\equiv\delta_1\tau_0^{-1}\,dp/dx $ were held constant. (τ0 is the shear stress at the wall and δ1 is the displacement thickness.)Tabular and graphical results are presented.

Evolution of a moderately short turbulent boundary layer in a severe pressure gradient

1974 ◽  
Vol 64 (4) ◽  
pp. 763-774 ◽  
Author(s):  
R. G. Deissler
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Reynolds Shear Stress ◽  
Pressure Gradients ◽  
Mean Velocity ◽  
Mass Injection ◽  
The Mean ◽  
Theoretical Results

The early and intermediate development of a highly accelerated (or decelerated) turbulent boundary layer is analysed. For sufficiently large accelerations (or pressure gradients) and for total normal strains which are not excessive, the equation for the Reynolds shear stress simplifies to give a stress that remains approximately constant as it is convected along streamlines. The theoretical results for the evolution of the mean velocity in favourable and adverse pressure gradients agree well with experiment for the cases considered. A calculation which includes mass injection at the wall is also given.

The accelerated fully rough turbulent boundary layer

1977 ◽  
Vol 82 (3) ◽  
pp. 507-528 ◽  
Author(s):  
Hugh W. Coleman ◽  
Robert J. Moffat ◽  
William M. Kays
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Stress Tensor ◽  
Skin Friction ◽  
Shape Factor ◽  
Reynolds Shear Stress ◽  
Smooth Wall ◽  
Mean Velocity

The behaviour of a fully rough turbulent boundary layer subjected to favourable pressure gradients both with and without blowing was investigated experimentally using a porous test surface composed of densely packed spheres of uniform size. Measurements of profiles of mean velocity and the components of the Reynolds-stress tensor are reported for both unblown and blown layers. Skin-friction coefficients were determined from measurements of the Reynolds shear stress and mean velocity.An appropriate acceleration parameterKrfor fully rough layers is defined which is dependent on a characteristic roughness dimension but independent of molecular viscosity. For a constant blowing fractionFgreater than or equal to zero, the fully rough turbulent boundary layer reaches an equilibrium state whenKris held constant. Profiles of the mean velocity and the components of the Reynolds-stress tensor are then similar in the flow direction and the skin-friction coefficient, momentum thickness, boundary-layer shape factor and the Clauser shape factor and pressure-gradient parameter all become constant.Acceleration of a fully rough layer decreases the normalized turbulent kinetic energy and makes the turbulence field much less isotropic in the inner region (forFequal to zero) compared with zero-pressure-gradient fully rough layers. The values of the Reynolds-shear-stress correlation coefficients, however, are unaffected by acceleration or blowing and are identical with values previously reported for smooth-wall and zero-pressure-gradient rough-wall flows. Increasing values of the roughness Reynolds number with acceleration indicate that the fully rough layer does not tend towards the transitionally rough or smooth-wall state when accelerated.

A Superposition Analysis of the Turbulent Boundary Layer in an Adverse Pressure Gradient

1951 ◽  
Vol 18 (1) ◽  
pp. 95-100
Author(s):  
Donald Ross ◽  
J. M. Robertson
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Wall Shear Stress ◽  
Turbulent Boundary Layer ◽  
Velocity Profile ◽  
Pressure Gradient ◽  
Adverse Pressure Gradient ◽  
Pressure Recovery ◽  
Stress Coefficient ◽  
Wall Shear

Abstract As an interim solution to the problem of the turbulent boundary layer in an adverse pressure gradient, a super-position method of analysis has been developed. In this method, the velocity profile is considered to be the result of two effects: the wall shear stress and the pressure recovery. These are superimposed, yielding an expression for the velocity profiles which approximate measured distributions. The theory also leads to a more reasonable expression for the wall shear-stress coefficient.

Predicting Turbulent Boundary Layer Wall Pressure Fluctuations in Adverse Pressure Gradients

2005 ◽  
Author(s):  
Frank J. Aldrich
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Pressure Fluctuations ◽  
Adverse Pressure Gradient ◽  
Wall Pressure ◽  
Prediction Tool ◽  
Pressure Gradients ◽  
Wall Pressure Fluctuations ◽  
The Difference

A physics-based approach is employed and a new prediction tool is developed to predict the wavevector-frequency spectrum of the turbulent boundary layer wall pressure fluctuations for subsonic airfoils under the influence of adverse pressure gradients. The prediction tool uses an explicit relationship developed by D. M. Chase, which is based on a fit to zero pressure gradient data. The tool takes into account the boundary layer edge velocity distribution and geometry of the airfoil, including the blade chord and thickness. Comparison to experimental adverse pressure gradient data shows a need for an update to the modeling constants of the Chase model. To optimize the correlation between the predicted turbulent boundary layer wall pressure spectrum and the experimental data, an optimization code (iSIGHT) is employed. This optimization module is used to minimize the absolute value of the difference (in dB) between the predicted values and those measured across the analysis frequency range. An optimized set of modeling constants is derived that provides reasonable agreement with the measurements.

scholarly journals On the generation of the mean velocity profile for turbulent boundary layers with pressure gradient under equilibrium conditions

2012 ◽  
Vol 116 (1180) ◽  
pp. 569-598 ◽  
Author(s):  
A. Rona ◽  
M. Monti ◽  
C. Airiau
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Velocity Profile ◽  
Pressure Gradient ◽  
Fluid Dynamic ◽  
Predictive Ability ◽  
Adverse Pressure Gradient ◽  
Computational Domain ◽  
Mean Velocity ◽  
Number Range

AbstractThe generation of a fully turbulent boundary layer profile is investigated using analytical and numerical methods over the Reynolds number range 422 ≤ Reθ≤ 31,000. The numerical method uses a new mixing length blending function. The predictions are validated against reference wind tunnel measurements under zero streamwise pressure gradient. The methods are then tested for low and moderate adverse pressure gradients. Comparison against experiment and DNS data show a good predictive ability under zero pressure gradient and moderate adverse pressure gradient, with both methods providing a complete velocity profile through the viscous sub-layer down to the wall. These methods are useful computational fluid dynamic tools for generating an equilibrium thick turbulent boundary layer at the computational domain inflow.

Turbulent boundary layers in decreasing adverse pressure gradients

1966 ◽  
Vol 26 (3) ◽  
pp. 481-506 ◽  
Author(s):  
A. E. Perry
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Adverse Pressure Gradient ◽  
Turbulent Boundary Layers ◽  
Pressure Gradients ◽  
Streamwise Direction ◽  
Mean Velocity ◽  
Boundary Layer Development ◽  
Regional Similarity ◽  
Layer Development

The results of a detailed mean velocity survey of a smooth-wall turbulent boundary layer in an adverse pressure gradient are described. Close to the wall, a variety of profiles shapes were observed. Progressing in the streamwise direction, logarithmic, ½-power, linear and$\frac{3}{2}$-power distributions seemed to form, and generally each predominated at a different stage of the boundary-layer development. It is believed that the phenomenon occurred because of the nature of the pressure gradient imposed (an initially high gradient which fell to low values as the boundary layer developed) and attempts are made to describe the flow by an extension of the regional similarity hypothesis proposed by Perry, Bell & Joubert (1966). Data from other sources is limited but comparisons with the author's results are encouraging.

Supplementary Boundary-Layer Approximations for Turbulent Flow

1989 ◽  
Vol 111 (4) ◽  
pp. 420-427 ◽  
Author(s):  
L. C. Thomas ◽  
S. M. F. Hasani
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Wall Shear Stress ◽  
Pressure Gradient ◽  
Adverse Pressure Gradient ◽  
Boundary Layer Flows ◽  
Mean Velocity ◽  
Wide Range ◽  
The Mean ◽  
Wall Shear

Approximations for total stress τ and mean velocity u are developed in this paper for transpired turbulent boundary layer flows. These supplementary boundary-layer approximations are tested for a wide range of near equilibrium flows and are incorporated into an inner law method for evaluating the mean wall shear stress τ0. The testing of the proposed approximations for τ and u indicates good agreement with well-documented data for moderate rates of blowing and suction and pressure gradient. These evaluations also reveal limitations in the familiar logarithmic law that has traditionally been used in the determination of wall shear stress for non-transpired boundary-layer flows. The calculations for τ0 obtained by the inner law method developed in this paper are found to be consistent with results obtained by the modern Reynolds stress method for a broad range of near equilibrium conditions. However, the use of the proposed inner law method in evaluating the mean wall shear stress for early classic near equilibrium flow brings to question the reliability of the results for τ0 reported for adverse pressure gradient flows in the 1968 Stanford Conference Proceedings.

History effects and near equilibrium in adverse-pressure-gradient turbulent boundary layers

2017 ◽  
Vol 820 ◽  
pp. 667-692 ◽  
Author(s):  
A. Bobke ◽  
R. Vinuesa ◽  
R. Örlü ◽  
P. Schlatter
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Adverse Pressure Gradient ◽  
Turbulent Boundary Layers ◽  
Mean Velocity ◽  
History Effects ◽  
Displacement Thickness ◽  
Gradient Parameter

Turbulent boundary layers under adverse pressure gradients are studied using well-resolved large-eddy simulations (LES) with the goal of assessing the influence of the streamwise pressure-gradient development. Near-equilibrium boundary layers were characterized through the Clauser pressure-gradient parameter $\unicode[STIX]{x1D6FD}$. In order to fulfil the near-equilibrium conditions, the free stream velocity was prescribed such that it followed a power-law distribution. The turbulence statistics pertaining to cases with a constant value of $\unicode[STIX]{x1D6FD}$ (extending up to approximately 40 boundary-layer thicknesses) were compared with cases with non-constant $\unicode[STIX]{x1D6FD}$ distributions at matched values of $\unicode[STIX]{x1D6FD}$ and friction Reynolds number $Re_{\unicode[STIX]{x1D70F}}$. An additional case at matched Reynolds number based on displacement thickness $Re_{\unicode[STIX]{x1D6FF}^{\ast }}$ was also considered. It was noticed that non-constant $\unicode[STIX]{x1D6FD}$ cases appear to approach the conditions of equivalent constant $\unicode[STIX]{x1D6FD}$ cases after long streamwise distances (approximately 7 boundary-layer thicknesses). The relevance of the constant $\unicode[STIX]{x1D6FD}$ cases lies in the fact that they define a ‘canonical’ state of the boundary layer, uniquely characterized by $\unicode[STIX]{x1D6FD}$ and $Re$. The investigations on the flat plate were extended to the flow around a wing section overlapping in terms of $\unicode[STIX]{x1D6FD}$ and $Re$. Comparisons with the flat-plate cases at matched values of $\unicode[STIX]{x1D6FD}$ and $Re$ revealed that the different development history of the turbulent boundary layer on the wing section leads to a less pronounced wake in the mean velocity as well as a weaker second peak in the Reynolds stresses. This is due to the weaker accumulated effect of the $\unicode[STIX]{x1D6FD}$ history. Furthermore, a scaling law suggested by Kitsios et al. (Intl J. Heat Fluid Flow, vol. 61, 2016, pp. 129–136), proposing the edge velocity and the displacement thickness as scaling parameters, was tested on two constant-pressure-gradient parameter cases. The mean velocity and Reynolds-stress profiles were found to be dependent on the downstream development. The present work is the first step towards assessing history effects in adverse-pressure-gradient turbulent boundary layers and highlights the fact that the values of the Clauser pressure-gradient parameter and the Reynolds number are not sufficient to characterize the state of the boundary layer.

Direct measurements of skin friction in a turbulent boundary layer with a strong adverse pressure gradient

1980 ◽  
Vol 101 (1) ◽  
pp. 79-95 ◽  
Author(s):  
D. Frei ◽  
H. Thomann
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Skin Friction ◽  
Circular Cross Section ◽  
Adverse Pressure Gradient ◽  
Small Element ◽  
Pressure Gradients ◽  
Local Pressure ◽  
Friction Forces

This paper describes a new balance, suitable for direct measurement of skin friction in turbulent boundary layers with severe pressure gradients. The gaps between the floating element and the surrounding wall are filled with a liquid in order to eliminate disturbing pressure forces on the element. The resulting friction forces are measured with piezo-electric transducers with high sensitivity and extremely small element displacement.Skin friction measurements were taken in the turbulent boundary layer of a wind tunnel with circular cross-section at M [les ] 0·25. Severe adverse pressure gradients were generated by means of a step on the wall or, alternatively, by a conical centre body.The new apparatus was mainly used to investigate the error of Preston tubes in adverse pressure gradients. It was necessary to develop a new measuring technique to improve the repeatability of the Preston tube readings.The Preston tube error was found to depend on both the local pressure gradient P = (dp/dx) ν/ρ3τ and on the Preston tube diameter uτd/ν and to be independent of the upstream pressure distribution for the range of parameters covered by the experiments.

Sign in / Sign up

Export Citation Format

Share Document