Identification of Nanocrystalline Inclusions in Bismuth-Doped Silica Fibers and Preforms

2016 ◽  
Vol 22 (5) ◽  
pp. 987-996 ◽  
Author(s):  
Liudmila D. Iskhakova ◽  
Filipp O. Milovich ◽  
Valery M. Mashinsky ◽  
Alexander S. Zlenko ◽  
Sergey E. Borisovsky ◽  
...  
Keyword(s):  
Optical Fibers ◽  
Room Temperature ◽  
Optical Loss ◽  
Laser Generation ◽  
Dopant Distribution ◽  
X Ray ◽  
The Core ◽  
Silica Fibers ◽  
Transmission Electron ◽  
Bismuth Concentration

AbstractThe nature of nanocrystalline inclusions and dopant distribution in bismuth-doped silicate fibers and preforms are studied by scanning and transmission electron microscopy, and energy and wavelength-dispersive X-ray microanalysis. The core compositions are Bi:SiO2, Bi:Al2O3–SiO2, Bi:GeO2–SiO2, Bi:Al2O3–GeO2–SiO2, and Bi:P2O5–Al2O3–GeO2–SiO2. Nanocrystals of metallic Bi, Bi2O3, SiO2, GeO2, and Bi4(GeO4)3 are observed in these glasses. These inclusions can be the reason for the background optical loss in bismuth-doped optical fibers. The bismuth concentration of 0.0048±0.0006 at% is directly measured in aluminosilicate optical fibers with effective laser generation (slope efficiency of 27% at room temperature).

Preparation and Characterization of Gold-Loaded Magnetite/Silica Core-Shell Composites

2016 ◽  
Vol 42 ◽  
pp. 47-52
Author(s):  
Dan Dan Huang ◽  
Zhao Dai ◽  
Kun Yang ◽  
Yuan Yuan Chu
Keyword(s):  
Room Temperature ◽  
Solvothermal Reaction ◽  
Core Shell ◽  
X Ray Diffraction ◽  
X Ray ◽  
The Core ◽  
Transmission Electron ◽  
Silica Core ◽  
Shell Particles

The fabrication of gold-loaded magnetite/silica core-shell particles was presented in this paper. First, 250 nm of magnetic Fe3O4 nanoparticles were prepared by solvothermal reaction. Then, the Fe3O4 particles were coated by SiO2, and Au nanoparticles (AuNPs), respectively. The core-shell structure of these microspheres was confirmed by transmission electron microscopy (TEM) and Power X-ray diffraction (XRD). The magnetic property of the core-shell microspheres was investigated at room temperature. The results indicated that the core-shell composites had a well-retained high magnetic intensity, thus it can be easily separated from the mixture in less than a few minutes by simply using a magnet.

scholarly journals Microscopy characterization of doped fibers

2004 ◽  
Vol 22 (3) ◽  
pp. 351-354 ◽  
Author(s):  
M. MILANI ◽  
D. BATANI ◽  
M. BALLERINI ◽  
A. POZZI ◽  
C. SAVOIA
Keyword(s):  
Spatial Resolution ◽  
Optical Fibers ◽  
Single Mode ◽  
Dopant Distribution ◽  
X Ray ◽  
The Core ◽  
Microscopy Technique ◽  
Doped Fibers ◽  
Microscopy Characterization

The use of the Soft X-ray Contact Microscopy technique is discussed as a possible new tool to get information on dopant distribution in the core of single-mode optical fibers with 50 nm spatial resolution.

Photoluminescence Enhancement of CdS Nanocrystals Fabricated on Dithiocarbamate Functionalized PET Substrates

2012 ◽  
Vol 512-515 ◽  
pp. 1511-1515
Author(s):  
Chun Lin Zhao ◽  
Li Xing ◽  
Xiao Hong Liang ◽  
Jun Hui Xiang ◽  
Fu Shi Zhang ◽  
...  
Keyword(s):  
Room Temperature ◽  
Hexagonal Structure ◽  
Diffraction Measurement ◽  
X Ray Diffraction ◽  
Visible Absorption ◽  
X Ray ◽  
Cds Nanocrystals ◽  
Morphological Studies ◽  
Transmission Electron

Cadmium sulfide (CdS) nanocrystals (NCs) were self-assembled and in-situ immobilized on the dithiocarbamate (DTCs)-functionalized polyethylene glycol terephthalate (PET) substrates between the organic (carbon disulfide diffused in n-hexane) –aqueous (ethylenediamine and Cd2+ dissolved in water) interface at room temperature. Powder X-ray diffraction measurement revealed the hexagonal structure of CdS nanocrystals. Morphological studies performed by scanning electron microscopy (SEM) and high-resolution transmission electron microscope (HRTEM) showed the island-like structure of CdS nanocrystals on PET substrates, as well as energy-dispersive X-ray spectroscopy (EDS) confirmed the stoichiometries of CdS nanocrystals. The optical properties of DTCs modified CdS nanocrystals were thoroughly investigated by ultraviolet-visible absorption spectroscopy (UV-vis) and fluorescence spectroscopy. The as-prepared DTCs present intrinsic hydrophobicity and strong affinity for CdS nanocrystals.

scholarly journals Facile Organometallic Synthesis of Fe-Based Nanomaterials by Hot Injection Reaction

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1141
Author(s):  
Georgia Basina ◽  
Hafsa Khurshid ◽  
Nikolaos Tzitzios ◽  
George Hadjipanayis ◽  
Vasileios Tzitzios
Keyword(s):  
Room Temperature ◽  
Colloidal Particles ◽  
Iron Pentacarbonyl ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
Organometallic Synthesis ◽  
X Ray ◽  
Transmission Electron ◽  
Hot Injection ◽  
The Stability

Fe-based colloids with a core/shell structure consisting of metallic iron and iron oxide were synthesized by a facile hot injection reaction of iron pentacarbonyl in a multi-surfactant mixture. The size of the colloidal particles was affected by the reaction temperature and the results demonstrated that their stability against complete oxidation related to their size. The crystal structure and the morphology were identified by powder X-ray diffraction and transmission electron microscopy, while the magnetic properties were studied at room temperature with a vibrating sample magnetometer. The injection temperature plays a very crucial role and higher temperatures enhance the stability and the resistance against oxidation. For the case of injection at 315 °C, the nanoparticles had around a 10 nm mean diameter and revealed 132 emu/g. Remarkably, a stable dispersion was created due to the colloids’ surface functionalization in a nonpolar solvent.

ION CHANNELING AND PIXE STUDIES OF S IMPLANTATION IN GaAs

1992 ◽  
Vol 02 (02) ◽  
pp. 151-159
Author(s):  
LIU SHIJIE ◽  
WANG JIANG ◽  
HU ZAOHUEI ◽  
XIA ZHONGHUONG ◽  
GAO ZHIGIANG ◽  
...  
Keyword(s):  
Room Temperature ◽  
Dislocation Loops ◽  
Good Recovery ◽  
Electrical Measurements ◽  
X Ray ◽  
Defect Complexes ◽  
Ion Channeling ◽  
Transmission Electron ◽  
Activation Efficiency ◽  
Very High

GaAs (100) crystals were implanted with 100 keV S+ to a dose of 3×1015 cm−2 in a nonchanneling direction at room temperature, and treated with rapid thermal annealing (RTA). He+ Rutherford backscattering and particle-induced X-ray emission in channeling mode in combination with transmission electron microscopy (TEM) were used to study the damage and the lattice location of S atoms. It is revealed that the RTA at 950 °C for 10 sec has resulted in a very good recovery of crystallinity with a few residual defects in the form of dislocation loops, and a very high substitutionality (~90%). The activation efficiency and the Hall mobility of the implanted samples are found to be low after the electrical measurements. Based on these results an extended dopant diffusion effect for the residual defects and a correlation between the electrical properties and defect complexes are suggested.

Synthesis and Photoluminescence Properties of Novel SnO2 Zigzag Nanoribbons

2010 ◽  
Vol 97-101 ◽  
pp. 4213-4216
Author(s):  
Jian Xiong Liu ◽  
Zheng Yu Wu ◽  
Guo Wen Meng ◽  
Zhao Lin Zhan
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Vapour Deposition ◽  
Chemical Vapour ◽  
Photoluminescence Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Ceramic Boat

Novel single-crystalline SnO2 zigzag nanoribbons have been successfully synthesized by chemical vapour deposition. Sn powder in a ceramic boat covered with Si plates was heated at 1100°C in a flowing argon atmosphere to get deposits on a Si wafers. The main part of deposits is SnO2 zigzag nanoribbons. They were characterized by means of X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM) and selected-area electron diffraction (SAED). SEM observations reveal that the SnO2 zigzag nanoribbons are almost uniform, with lengths near to several hundred micrometers and have a good periodically tuned microstructure as the same zigzag angle and growth directions. Possible growth mechanism of these zigzag nanoribbons was discussed. A room temperature PL spectrum of the zigzag nanoribbons shows three peaks at 373nm, 421nm and 477nm.The novel zigzag microstructures will provide a new candidate for potential application.

Evaluation Humidity Sensing Properties of Graphene/HS-TiO2 Nanocomposites

2021 ◽  
Vol 21 (10) ◽  
pp. 5143-5149
Author(s):  
Zhen Zhu ◽  
Wang-De Lin
Keyword(s):  
Room Temperature ◽  
Response Times ◽  
Sol Gel ◽  
Hollow Spheres ◽  
High Sensitivity ◽  
Humidity Sensing ◽  
X Ray ◽  
Transmission Electron ◽  
Recovery Times ◽  
Relative Humidity Range

This paper reports on a nanocomposite synthesized by sol–gel procedure comprising graphene sheets with hollow spheres of titanium dioxide (G/HS-TiO2) with varying weight percentages of graphene for the purpose of humidity sensors. The surface morphology of the nanocomposite was characterized using transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). The structural properties were examined using X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR). The response to 12–80% RH at room temperature exhibited sensitivity (S = 135). However, the relative humidity range of 12–90% at room temperature exhibited higher sensitivity (S = 557). Sensors fabricated using the proposed nanocomposite exhibited high sensitivity to humidity, high stability, rapid response times, and rapid recovery times with hysteresis error of less than 1.79%. These results demonstrate the outstanding potential of his material for the monitoring of atmospheric humidity. This study also sought to elucidate the mechanisms underlying humidity sensing performance.

Preparation and Properties of Nano-Crystalline Cellulose Electro-Rheological Fluid

2015 ◽  
Vol 815 ◽  
pp. 217-221
Author(s):  
Ling Li Xu ◽  
Xing Ling Shi ◽  
Qing Liang Wang
Keyword(s):  
Room Temperature ◽  
Silicone Oil ◽  
Strong Acid ◽  
Crystalline Cellulose ◽  
Methyl Silicone ◽  
Shearing Stress ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Crystalline ◽  
Transmission Electron

nanocrystalline cellulose (NCC) was prepared from micro-crystalline cellulose (MCC) by strong acid hydrolysis. The characteristics of such particle were studied by transmission electron microscopy, X-ray diffraction and Fourier transform infrared spectroscopy. Electro-rheological fluids (ERF) were prepared by dispersing NCC and MCC in methyl-silicone oil, and their ER effects were measured. Experimental results indicated that NCC ERF exhibited a remarkable ER effect. The highest static shearing stress of NCC ERF (3.5 g/ml) was 5.1 kPa at the room temperature under a 4 .2 kV/mm electric field, increased about 5.5 times compared to MCC ERF, and sedimentation of NCC ERF was not observed even after 60 days.

A Facile Fynthesis of ZnS Nanostructures via Liquid-Solid Reactions

2014 ◽  
Vol 979 ◽  
pp. 184-187
Author(s):  
Weerachon Phoohinkong ◽  
Thitinat Sukonket ◽  
Udomsak Kitthawee
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Inorganic Salts ◽  
Chloride Salt ◽  
X Ray ◽  
Commercial Grade ◽  
Transmission Electron ◽  
Salt Addition ◽  
20 Nm ◽  
Scanning Electron

Zinc sulfide (ZnS) nanostructures are important materials for many technologies such as sensors, infrared windows, transistors, LED displays, and solar cells. However, many methods of synthesizing ZnS nanostructures are complex and require expensive equipment. In this study, a liquid-solid chemical reaction without surfactant was used to synthesize ZnS at room temperature. In addition, commercial grade zinc oxide (ZnO) particles were used as a precursor. The effect of the addition of acids and inorganic salts were investigated. The products were characterized by field emission scanning electron microscopy (FESEM) coupled with energy-dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM). The results show that the nanoparticles of ZnS were obtained in hydrochloric acid and acetic acid addition. The diameters were in the range of 10 to 20 nm and 50 to 100 nm, respectively. In the case of a sodium chloride salt addition, a ZnS structure was obtained with a particle size of approximately 5 nm and a flake-like morphology.

New method for the production of bulk amorphous materials of Nd–Fe–B alloys

2005 ◽  
Vol 20 (3) ◽  
pp. 563-566 ◽  
Author(s):  
Tetsuji Saito ◽  
Hiroyuku Takeishi ◽  
Noboru Nakayama
Keyword(s):  
Electron Microscopy ◽  
Amorphous Materials ◽  
Room Temperature ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Bulk Materials ◽  
X Ray ◽  
Transmission Electron ◽  
Melt Spun ◽  
Melt Spun Ribbons

We report a new compression shearing method for the production of bulk amorphous materials. In this study, amorphous Nd–Fe–B melt-spun ribbons were successfully consolidated into bulk form at room temperature by the compression shearing method. X-ray diffraction and transmission electron microscopy studies revealed that the amorphous structure was well maintained in the bulk materials. The resultant bulk materials exhibited the same magnetic properties as the original amorphous Nd–Fe–B materials.

Sign in / Sign up

Export Citation Format

Share Document