scholarly journals Combined light- and heat-induced shape memory behavior of anthracene-based epoxy elastomers

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Yuzhan Li ◽  
Monojoy Goswami ◽  
Yuehong Zhang ◽  
Tuan Liu ◽  
Jinwen Zhang ◽  
...  
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Shape Memory ◽  
Uv Light ◽  
Dynamic Mechanical Properties ◽  
Stimuli Responsive ◽  
Epoxy Monomer ◽  
Dynamics Simulations ◽  
External Stimuli

AbstractThe development of multi-stimuli-responsive shape memory polymers has received increasing attention because of its scientific and technological significance. In this work, epoxy elastomers with reversible crosslinks are synthesized by polymerizing an anthracene-functionalized epoxy monomer, a diepoxy comonomer, and a dicarboxylic acid curing agent. The synthesized elastomers exhibit active responses to both light and heat enabled by the incorporated anthracene groups. When exposed to 365 nm UV light, additional crosslinking points are created by the photo-induced dimerization of pendant anthracene groups. The formation of the crosslinking points increases modulus and glass transition temperature of the elastomers, allowing for the fixation of a temporary shape at room temperature. The temporary shape remains stable until an external heat stimulus is applied to trigger the scission of the dimerized anthracene, which reduces the modulus and glass transition temperature and allows the elastomers to recover their original shapes. The effects of external stimuli on the thermal and dynamic mechanical properties of the elastomers are investigated experimentally and are correlated with molecular dynamics simulations that reveal the changes of structure and dynamics of the anthracene molecules and flexible chains.

scholarly journals Buckling and vibration analysis of shape memory laminated composite beams under axially heterogeneous in-plane loads in the glass transition temperature region

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Nilesh Tiwari ◽  
A. A. Shaikh
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Boundary Conditions ◽  
Shape Memory ◽  
Transition Region ◽  
Shape Memory Polymer ◽  
Shear Deformation Theory ◽  
Effect Of Temperature ◽  
Glass Transition Region

AbstractBuckling and vibration study of the shape memory polymer composites (SMPC) across the glass transition temperature under heterogeneous loading conditions are presented. Finite element analysis based on C° continuity equation through the higher order shear deformation theory (HSDT) is employed considering non linear Von Karman approach to estimate critical buckling and vibration for the temperature span from 273 to 373 K. Extensive numerical investigations are presented to understand the effect of temperature, boundary conditions, aspect ratio, fiber orientations, laminate stacking and modes of phenomenon on the buckling and vibration behavior of SMPC beam along with the validation and convergence study. Effect of thermal conditions, particularly in the glass transition region of the shape memory polymer, is considerable and presents cohesive relation between dynamic modulus properties with magnitude of critical buckling and vibration. Moreover, it has also been inferred that type of axial loading condition along with the corresponding boundary conditions significantly affect the buckling and vibration load across the glass transition region.

scholarly journals Triple-Shape Memory Behavior of Modified Lactide/Glycolide Copolymers

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2984
Author(s):  
Anna Smola-Dmochowska ◽  
Natalia Śmigiel-Gac ◽  
Bożena Kaczmarczyk ◽  
Michał Sobota ◽  
Henryk Janeczek ◽  
...  
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Shape Memory ◽  
Hydroxyl Groups ◽  
Butylene Succinate ◽  
Shape Memory Behavior ◽  
Triple Shape Memory ◽  
High Flexibility ◽  
Bioresorbable Implants

The paper presents the formation and properties of biodegradable thermoplastic blends with triple-shape memory behavior, which were obtained by the blending and extrusion of poly(l-lactide-co-glycolide) and bioresorbable aliphatic oligoesters with side hydroxyl groups: oligo (butylene succinate-co-butylene citrate) and oligo(butylene citrate). Addition of the oligoesters to poly (l-lactide-co-glycolide) reduces the glass transition temperature (Tg) and also increases the flexibility and shape memory behavior of the final blends. Among the tested blends, materials containing less than 20 wt % of oligo (butylene succinate-co-butylene citrate) seem especially promising for biomedical applications as materials for manufacturing bioresorbable implants with high flexibility and relatively good mechanical properties. These blends show compatibility, exhibiting one glass transition temperature and macroscopically uniform physical properties.

The Effects of Chemical Resistance for Nanocomposite Materials via Nano-Silica Addition into Glass Fiber/Epoxy

2013 ◽  
Vol 853 ◽  
pp. 28-33
Author(s):  
Huey Ling Chang ◽  
Chih Ming Chen ◽  
Kung Liang Lin ◽  
Bor Kae Chang
Keyword(s):  
Mechanical Properties ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Glass Fiber ◽  
Epoxy Resin ◽  
Storage Modulus ◽  
Chemical Resistance ◽  
Dynamic Mechanical Properties ◽  
Silica Nanopowder

Nanocomposite samples containing epoxy resin, glass fiber and 0~2 wt.% SiO2 nanopowder are prepared. The effects of SiO2 addition on the chemical resistance, glass transition temperature (Tg) and dynamic mechanical properties of the various samples are then observed. The chemical resistance of the nanocomposite specimens is compared with that of pure glass fiber/epoxy composite specimens when tested in acetone. The results show that the addition of 2 wt.% SiO2 increases the value of storage modulus by 1646MPa compared to that of the sample containing no silica nanopowder. Following immersion in acetone, all the nanocomposite specimen storage modulus decreased, but the addition of SiO2 reduced the decline, where the 2 wt. % samples decrease from 11.76% reduction to 0.84% and no significant change in the Tg compared to that of the sample with no silica nanopowder. Therefore, the experimental results indicate that 2 wt.% SiO2 addition is beneficial in improving chemical resistance, glass transition temperature, and dynamic mechanical properties of epoxy resin / glass fiber nanocomposites.

Free, partial, and fully constrained recovery analysis of cold-programmed shape memory epoxy/carbon nanotube nanocomposites: Experiments and predictions

2018 ◽  
Vol 29 (10) ◽  
pp. 2164-2176 ◽  
Author(s):  
R Abishera ◽  
R Velmurugan ◽  
KV Nagendra Gopal
Keyword(s):  
Glass Transition ◽  
Carbon Nanotube ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Shape Memory ◽  
Thermally Activated ◽  
Large Structures ◽  
Multi Walled Carbon Nanotube ◽  
Optical Strain Measurement ◽  
Optical Strain

Thermally activated shape memory polymers are typically programmed by initially heating the material above the glass transition temperature ( Tg), deforming to the desired shape, cooling below Tg, and unloading to fix the temporary shape. This process of deforming at high temperatures becomes a time-, labor-, and energy-expensive process while applying to large structures. Alternatively, materials with reversible plasticity shape memory property can be programmed at temperatures well below the glass transition temperature which offers several advantages over conventional programming. Here, the free, partial, and fully constrained recovery analysis of cold-programmed multi-walled carbon nanotube–reinforced epoxy nanocomposites is presented. The free recovery analysis involves heating the temporary shape above Tg without any constraints (zero stress), and for fully constrained recovery analysis, the temporary shape is held constant while heating. The partially constrained recovery behavior is studied by applying a constant stress of 10%, 25%, and 50% of the maximum recovery stress obtained from the completely constrained recovery analysis. The samples are also characterized for their thermal, morphological, and mechanical properties. A non-contact optical strain measurement method is used to measure the strains during cold-programming and shape recovery. The different recovery behaviors are analyzed by using a thermo-viscoelastic–viscoplastic model, and the predictions are compared with the experimental results.

scholarly journals Modelling the Mechanical and Strain Recovery Behaviour of Partially Crystalline PLA

Polymers ◽  
2019 ◽  
Vol 11 (8) ◽  
pp. 1342 ◽  
Author(s):  
John Sweeney ◽  
Paul Spencer ◽  
Karthik Nair ◽  
Phil Coates
Keyword(s):  
Finite Element ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Stress Relaxation ◽  
Shape Memory ◽  
Yield Stress ◽  
Amorphous Phase ◽  
Strain Recovery ◽  
Stress Strain

This is a study of the modelling and prediction of strain recovery in a polylactide. Strain recovery near the glass transition temperature is the underlying mechanism for the shape memory in an amorphous polymer. The investigation is aimed at modelling such shape memory behaviour. A PLA-based copolymer is subjected to stress–strain, stress relaxation and strain recovery experiments at large strain at 60 °C just below its glass transition temperature. The material is 13% crystalline. Using published data on the mechanical properties of the crystals, finite element modelling was used to determine the effect of the crystal phase on the overall mechanical behaviour of the material, which was found to be significant. The finite element models were also used to relate the stress–strain results to the yield stress of the amorphous phase. This yield stress was found to possess strain rate dependence consistent with an Eyring process. Stress relaxation experiments were also interpreted in terms of the Eyring process, and a two-process Eyring-based model was defined that was capable of modelling strain recovery behaviour. This was essentially a model of the amorphous phase. It was shown to be capable of useful predictions of strain recovery.

Prediction of the glass transition temperature and design of phase diagrams of butadiene rubber and styrene–butadiene rubber via molecular dynamics simulations

2017 ◽  
Vol 19 (25) ◽  
pp. 16498-16506 ◽  
Author(s):  
Myung Shin Ryu ◽  
Hyoung Gyu Kim ◽  
Hyun You Kim ◽  
Kyung-Shin Min ◽  
Hak Joo Kim ◽  
...  
Keyword(s):  
Molecular Dynamics ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Molecular Dynamics Simulations ◽  
Phase Diagrams ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Dynamics Simulations ◽  
Styrene Butadiene

In this study, we developed an equation to evaluate the pseudo-ternary Tg of quaternary SBR and plotted the ternary contour Tg plot for SBR with a variety of styrene compositions.

Sign in / Sign up

Export Citation Format

Share Document