scholarly journals Personal Care Wastewater Treatment With Electro-coagulation and Electro-oxidation

2019 ◽  
Vol 125 ◽  
pp. 03008
Author(s):  
Rachmad Ardhianto ◽  
Arseto Yekti Bagastyo
Keyword(s):  
Removal Rate ◽  
Cod Removal ◽  
Aluminum Electrode ◽  
Personal Care ◽  
Electrochemical Processes ◽  
Initial Ph ◽  
Electro Oxidation ◽  
Aluminum Electrodes ◽  
Cod Removal Rate ◽  
Electro Coagulation

Personal care wastewater contains pharmaceuticals and personal care products (PPCPs). The compounds were in organic pollutants which have to be treated before water can be discharged. Electrochemical processes such as electro-coagulation and electro-oxidation were used to remove non-biodegradable in wastewater. Electro-coagulation as pretreatment using aluminum electrodes as anode and cathode. Electro-oxidation using Ti/Pt, and Ti/IrO2 as anode electrodes and variation of current 0,6 A, 0,7 A, 0,8 A and 1,0 A. Aluminum electrodes has effectiveness in removing COD, and TSS in electrocoagulation. Using aluminum electrodes remove COD, and TSS 76.1% (5.41 g) and 90.3% (6.10 g). Under initial pH, aluminum electrode does not cause a change in pH from initial pH (4.8-4.9). The removal efficiency of electrooxidation process using aluminum electrocoagulation effluent COD using Ti/Pt and Ti/IrO2 were 34,30% (1,55 g) and 39,71% (1,80 g). Increasing current when using Ti/IrO2 causes the COD removal rate to be more effective than using Ti/Pt. removal COD with 1.0 A gave the optimum COD removal were 34,30% (2,3 Ah/L; 1,55 g) with Ti/Pt, and 39,71% (2,3 Ah/L; 1,80 g) with Ti/IrO2 compared to 0,6 A (1,4 Ah/L), 0,7 A (1,6 Ah/L), and 0.8 A (1,9 Ah/L).

Synergetic Degradation of Zidovudine Wastewater by Ultrasonic and Iron-Carbon Micro-Electrolysis

2011 ◽  
Vol 347-353 ◽  
pp. 1949-1952 ◽  
Author(s):  
Liang Li ◽  
Bing Zhe Xu ◽  
Chang Yu Lin ◽  
Xiao Min Hu
Keyword(s):  
Reaction Time ◽  
Degradation Rate ◽  
Removal Rate ◽  
Cod Removal ◽  
Mass Ratio ◽  
Initial Ph ◽  
Cod Removal Rate

Zidovudine wastewater is difficult to biodegradation due to high COD and toxicity. The synergetic treatment of Zidovudine wastewater by Ultrasonic and iron-carbon micro-electrolysis technology was studied. The influence of initial pH, reaction time, mass ratio of iron and carbon and mass ratio of iron and water on degradation rate of COD was researched. The result showed that the COD removal rate was only about 54.3% and the degradation speed is very slow when iron-carbon micro-electrolysis treated Zidovudine wastewater　separately. However, when ultrasonic synergy micro-electrolysis to treat Zidovudine wastewater, the COD removal rate could was up to 85% and the reaction time was also decreased. Moreover, the BOD5 / COD rose from 0.15 to 0.35, which meant the wastewater became easily biodegradable.

scholarly journals Catalytic Ozonation for Effective Degradation of Coal Chemical Biochemical Tail Water by Mn/Ce@RM Catalyst

Water ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 206
Author(s):  
Yicheng Wang ◽  
Yingkun Wang ◽  
Xi Lu ◽  
Wenquan Sun ◽  
Yanhua Xu ◽  
...  
Keyword(s):  
Reaction Time ◽  
Removal Rate ◽  
Catalytic Ozonation ◽  
Operating Conditions ◽  
Cod Removal ◽  
X Ray ◽  
Initial Ph ◽  
Catalyst Dosage ◽  
Cod Removal Rate ◽  
Tail Water

An Mn/Ce@red mud (RM) catalyst was prepared from RM via a doping–calcination method. Scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy were used to characterize the surface morphology, crystal morphology, and elemental composition of the Mn/Ce@RM catalyst, respectively. In addition, preparation and catalytic ozonation conditions were optimized, and the mechanism of catalytic ozonation was discussed. Lastly, a fuzzy analytic hierarchy process (FAHP) was adopted to evaluate the degradation of coal chemical biochemical tail water. The best preparation conditions for the Mn/Ce@RM catalyst were found to be as follows: (1) active component loading of 3%, (2) Mn/Ce doping ratio of 2:1, (3) calcination temperature of 550 °C, (4) calcination time of 240 min, and (5) fly ash floating bead doping of 10%. The chemical oxygen demand (COD) removal rate was 76.58% under this preparation condition. The characterization results suggested that the pore structure of the optimized Mn/Ce@RM catalyst was significantly improved. Mn and Ce were successfully loaded on the catalyst in the form of MnO2 and CeO2. The best operating conditions in the study were as follows: (1) reaction time of 80 min, (2) initial pH of 9, (3) ozone dosage of 2.0 g/h, (4) catalyst dosage of 62.5 g/L, and (5) COD removal rate of 84.96%. Mechanism analysis results showed that hydroxyl radicals (•OH) played a leading role in degrading organics in the biochemical tail water, and adsorption of RM and direct oxidation of ozone played a secondary role. FAHP was established on the basis of environmental impact, economic benefit, and energy consumption. Comprehensive evaluation by FAHP demonstrated that D3 (with an ozone dosage of 2.0 g/H, a catalyst dosage of 62.5 g/L, initial pH of 9, reaction time of 80 min, and a COD removal rate of 84.96%) was the best operating condition.

Performance of anode materials in electrochemical treatment system for indigo dyeing wastewater

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wei Zhang ◽  
Mengdi Zhang ◽  
Zhijie Huangfu ◽  
Jiming Yao ◽  
Yuan Xie
Keyword(s):  
Anode Materials ◽  
Electrolyte Concentration ◽  
Removal Rate ◽  
Electrochemical Treatment ◽  
Cod Removal ◽  
Aluminum Electrode ◽  
Dyeing Wastewater ◽  
Content Type ◽  
Indigo Dyeing ◽  
Cod Removal Rate

Purpose This study aims to explore suitable anode materials used in the electrochemical system for indigo dyeing wastewater, to achieve optimal treatment performances. Design/methodology/approach The single factor experiment was used to explore the optimum process parameters for electrochemical decolorization of indigo dyeing wastewater by changing the applied voltage, electrolysis time and electrolyte concentration. At the voltage of 9 V, the morphology of flocs with different electrolytic times was observed and the effect of electrolyte concentration on decolorization rate in two electrolyte systems was also investigated. Further analysis of chemical oxygen demand (COD) removal rate, anode weight loss and sediment quantity after electrochemical treatment of indigo dyeing wastewater were carried out. Findings Comprehensive considering the decolorization degree and COD removal rate of the wastewater, the aluminum electrode showed the best treatment effect among several common anode materials. With aluminum electrode as an anode, under conditions of applied voltage of 9 V, electrolysis time of 40 min and sodium sulfate concentration of 6 g/L, the decolorization percentage obtained was of 94.59% and the COD removal rate reached at 84.53%. Research limitations/implications In the electrochemical treatment of indigo dyeing wastewater, the aluminum electrode was found as an ideal anode material, which provided a reference for the choice of anodes. The electrodes used in this study were homogenous material and the composite material anode needed to be further researched. Practical implications It provided an effective and practical anode material choice for electrochemical degradation of indigo dyeing wastewater. Originality/value Combined with the influence of applied voltage, electrolysis time and electrolyte concentration and anode materials on decolorization degree and COD removal rate of indigo dyeing wastewater, providing a better electrochemical treatment system for dyehouse effluent.

Catalytic Wet Peroxide Oxidation of Dye Wastewater Using Fe2O3-CeO2/γ-Al2O3 as Catalyst

2014 ◽  
Vol 884-885 ◽  
pp. 29-32
Author(s):  
Hong Ya Li ◽  
Biao Yan ◽  
Bin Xia Zhao ◽  
Xiao Li Zhang
Keyword(s):  
Ph Value ◽  
Removal Rate ◽  
Cod Removal ◽  
Dye Wastewater ◽  
Peroxide Oxidation ◽  
Oxidation Method ◽  
Wet Peroxide Oxidation ◽  
Initial Ph ◽  
Catalytic Wet Peroxide Oxidation ◽  
Cod Removal Rate

Fe2O3-CeO2/γ-Al2O3 was used as catalyst for treating the dye wastewater by catalytic wet peroxide oxidation method, the effect of reaction temperature, initial pH value of the wastewater, dosage of catalyst and hydrogen peroxide on the COD removal were studied. Results showed that 90.3% of COD removal rate can be obtained under the condition of 90°C, pH=7, 0.8g catalyst/100 mL wasterwater, and 6mL H2O2 /100 mL wasterwater.

scholarly journals Pretreatment of printing and dyeing wastewater by Fe/C micro-electrolysis combined with H2O2 process

2018 ◽  
Vol 2017 (3) ◽  
pp. 707-717 ◽  
Author(s):  
Yan Wang ◽  
Xianwei Wu ◽  
Ju Yi ◽  
Lijun Chen ◽  
Tianxiang Lan ◽  
...  
Keyword(s):  
Removal Rate ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Coefficient Of Determination ◽  
H2o2 Concentration ◽  
Dyeing Wastewater ◽  
Spectra Analysis ◽  
Printing And Dyeing Wastewater ◽  
Initial Ph ◽  
Cod Removal Rate

Abstract A novel iron-carbon (Fe/C) micro-electrolysis combined with H2O2 (ICMH) process was proposed to pretreat the printing and dyeing wastewater (PDW), using a micro-electrolysis filling. The effects of H2O2 concentration, reaction time, initial pH, and Fe/C dosage on chemical oxygen demand (COD) removal rate of PDW were optimized by response surface methodology (RSM). The maximum COD removal rate was approximately 77.65% after 186 min treatment, when the concentration of H2O2, initial pH and the dosage of Fe/C were 8.88 g/L, 1.5 and 837 g/L, respectively. Analysis of variance (ANOVA) showed a high coefficient of determination value (R2 = 0.9780). And H2O2 concentration and initial pH were the key factors to improve the treatment effect. UV-Vis spectra indicated that a significant blue shift at 220 nm, attributing that fused aromatic hydrocarbons were degraded effectively. 3D-EEM spectra analysis showed that the water samples of PDW mainly contained three kinds of organic matter: refractory fulvic acid, soluble microbial metabolites and aromatic proteins, and the degradation rate of these was 81.76%, 53.78% and 70.83%, respectively.

scholarly journals Preparation and Application of Sewage Sludge Bio-char/zero Valent Iron (SSBC/ZVI) Composite for Improving the Biodegradability of a Real Chemical Synthesis-based Pharmaceutical Wastewater

2021 ◽  
Author(s):  
Gaoxiang Qi ◽  
Xiaobo Wang ◽  
Xuecheng Liu ◽  
Shen Yu
Keyword(s):  
Sewage Sludge ◽  
Chemical Synthesis ◽  
Removal Rate ◽  
Optimal Operation ◽  
Cod Removal ◽  
Pharmaceutical Wastewater ◽  
Operation Condition ◽  
Initial Ph ◽  
Cod Removal Rate ◽  
Pollutants Removal

Abstract A new kind of micro-electrolysis filler sewage sludge biochar/zero violent iron (SSBC/ZVI) composite was prepared for a real chemical synthesis based pharmaceutical wastewater (CSPW) pretreatment for improving the biodegradation index (BI). The optimal operation condition of micro-electrolysis system was obtained at HRT of 2 h, the initial pH of 3.0 and filler dosage of 100 g/L, with COD removal rate of 30.5%. Comparative analysis of raw and used SSBC/ZVI filler, GC-MS analysis of raw and treated pharmaceutical wastewater suggested that the pollutants removal was mainly attributed to the combination of reduction and oxidation, absorption of SSBC and flocculation effect of iron sludge. In addition, SSBC/ZVI exhibited relative high stability and excellent reusability for COD removal and BI improvement of real pharmaceutical wastewater. The results of this study provide new ideas of sewage sludge utilization for real wastewater pretreatment.

scholarly journals Ti/RuO2-IrO2-SnO2 Anode for Electrochemical Degradation of Pollutants in Pharmaceutical Wastewater: Optimization and Degradation Performances

2020 ◽  
Vol 13 (1) ◽  
pp. 126
Author(s):  
Guozhen Zhang ◽  
Xingxing Huang ◽  
Jinye Ma ◽  
Fuping Wu ◽  
Tianhong Zhou
Keyword(s):  
Removal Rate ◽  
Inorganic Compounds ◽  
Oxide Coating ◽  
X Ray Diffraction ◽  
Pharmaceutical Wastewater ◽  
High Concentration ◽  
Dimensionally Stable Anodes ◽  
X Ray ◽  
Initial Ph ◽  
Cod Removal Rate

Electrochemical oxidation technology is an effective technique to treat high-concentration wastewater, which can directly oxidize refractory pollutants into simple inorganic compounds such as H2O and CO2. In this work, two-dimensionally stable anodes, Ti/RuO2-IrO2-SnO2, have been developed in order to degrade organic pollutants from pharmaceutical wastewater. Characterization by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) showed that the oxide coating was successfully fabricated on the Ti plate surface. Electrocatalytic oxidation conditions of high concentration pharmaceutical wastewater was discussed and optimized, and the best results showed that the COD removal rate was 95.92% with the energy consumption was 58.09 kW·h/kgCOD under the electrode distance of 3 cm, current density of 8 mA/cm2, initial pH of 2, and air flow of 18 L/min.

Research of 6-Nitry Industrial Wastewater Treatment by Coagulation-Fenton Oxidation

2012 ◽  
Vol 518-523 ◽  
pp. 2745-2748
Author(s):  
Ling Yan Ren ◽  
Gang Xu
Keyword(s):  
Treatment Effect ◽  
Industrial Wastewater ◽  
Removal Rate ◽  
Sulfate Solution ◽  
Cod Removal ◽  
Fenton Oxidation ◽  
Fenton Reagent ◽  
Oxidation Treatment ◽  
Cod Removal Rate ◽  
Solution Acidity

The paper adopted Coagulation-Fenton Oxidation Method on treating the wastewater of 6-nitro-1,2 diazonium oxygroup naphthalene-4-sulfoacid production process (i.e. 6-nitry wastewater), introduced the treatment effect of the combined technology used on 6-nitry wastewater, and studied the factors influencing the treatment effect, to determine the reasonable parameters of the technology on treating 6-nitry wastewater. The results showed that Using polyaluminium chloride (mass fraction 2%) as flocculant for treating 6-nitry wastewater, the COD removal rate reached up to 48.7%; Making Fenton reagent oxidation treatment on coagulation yielding water, under the best conditions for solution acidity controlled at pH3 or so, in the 100 mL wastewater, 30% hydrogen peroxide was 5.0 mL, 0.5 mol/L ferrous sulfate solution was 4.0 mL, reaction time was 60 min, the COD removal rate could reach 98% or more.

Electrocoagulation and nanofiltration integrated process application in purification of bilge water using response surface methodology

2016 ◽  
Vol 74 (3) ◽  
pp. 564-579 ◽  
Author(s):  
Ceyhun Akarsu ◽  
Yasin Ozay ◽  
Nadir Dizge ◽  
H. Elif Gulsen ◽  
Hasan Ates ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Removal Efficiency ◽  
Cod Removal ◽  
Positive Sign ◽  
Aluminum Electrode ◽  
Integrated Process ◽  
Bilge Water ◽  
Cod Removal Efficiency ◽  
Initial Ph

Marine pollution has been considered an increasing problem because of the increase in sea transportation day by day. Therefore, a large volume of bilge water which contains petroleum, oil and hydrocarbons in high concentrations is generated from all types of ships. In this study, treatment of bilge water by electrocoagulation/electroflotation and nanofiltration integrated process is investigated as a function of voltage, time, and initial pH with aluminum electrode as both anode and cathode. Moreover, a commercial NF270 flat-sheet membrane was also used for further purification. Box–Behnken design combined with response surface methodology was used to study the response pattern and determine the optimum conditions for maximum chemical oxygen demand (COD) removal and minimum metal ion contents of bilge water. Three independent variables, namely voltage (5–15 V), initial pH (4.5–8.0) and time (30–90 min) were transformed to coded values. The COD removal percent, UV absorbance at 254 nm, pH value (after treatment), and concentration of metal ions (Ti, As, Cu, Cr, Zn, Sr, Mo) were obtained as responses. Analysis of variance results showed that all the models were significant except for Zn (P > 0.05), because the calculated F values for these models were less than the critical F value for the considered probability (P = 0.05). The obtained R2 and Radj2 values signified the correlation between the experimental data and predicted responses: except for the model of Zn concentration after treatment, the high R2 values showed the goodness of fit of the model. While the increase in the applied voltage showed negative effects, the increases in time and pH showed a positive effect on COD removal efficiency; also the most effective linear term was found as time. A positive sign of the interactive coefficients of the voltage–time and pH–time systems indicated synergistic effect on COD removal efficiency, whereas interaction between voltage and pH showed an antagonistic effect.

Study on Spray on Degradation of TNT-RDX Explosives Wastewater by Synergetic Ozonation

2013 ◽  
Vol 726-731 ◽  
pp. 2316-2319
Author(s):  
Hai Xia Duan
Keyword(s):  
Gas Phase ◽  
Removal Rate ◽  
Droplet Diameter ◽  
Cod Removal ◽  
The Self ◽  
Cod Removal Rate

TNT-RDX wastewater is hard to biodegrade and highly toxic. The self-made reactor was used to degrade the wastewater, spray and the conditions of droplet diameter, number of nozzle, spray height were clearly observed. The results show that the average COD removal rate of TNT-RDX wastewater was 69.6%.The spray conditions can improve the dispersion of the wastewater and increase the use of the residual ozone in gas phase. Keywords: Spray; TNT-RDX wastewater; ozone; UV; GAC

Sign in / Sign up

Export Citation Format

Share Document