scholarly journals Ti/RuO2-IrO2-SnO2 Anode for Electrochemical Degradation of Pollutants in Pharmaceutical Wastewater: Optimization and Degradation Performances

2020 ◽  
Vol 13 (1) ◽  
pp. 126
Author(s):  
Guozhen Zhang ◽  
Xingxing Huang ◽  
Jinye Ma ◽  
Fuping Wu ◽  
Tianhong Zhou
Keyword(s):  
Removal Rate ◽  
Inorganic Compounds ◽  
Oxide Coating ◽  
X Ray Diffraction ◽  
Pharmaceutical Wastewater ◽  
High Concentration ◽  
Dimensionally Stable Anodes ◽  
X Ray ◽  
Initial Ph ◽  
Cod Removal Rate

Electrochemical oxidation technology is an effective technique to treat high-concentration wastewater, which can directly oxidize refractory pollutants into simple inorganic compounds such as H2O and CO2. In this work, two-dimensionally stable anodes, Ti/RuO2-IrO2-SnO2, have been developed in order to degrade organic pollutants from pharmaceutical wastewater. Characterization by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) showed that the oxide coating was successfully fabricated on the Ti plate surface. Electrocatalytic oxidation conditions of high concentration pharmaceutical wastewater was discussed and optimized, and the best results showed that the COD removal rate was 95.92% with the energy consumption was 58.09 kW·h/kgCOD under the electrode distance of 3 cm, current density of 8 mA/cm2, initial pH of 2, and air flow of 18 L/min.

scholarly journals Heterogeneous Photo-Fenton Catalytic Degradation of Practical Pharmaceutical Wastewater by Modified Attapulgite Supported Multi-Metal Oxides

Water ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 156
Author(s):  
Manjing Lu ◽  
Jiaqi Wang ◽  
Yuzhong Wang ◽  
Zhengguang He
Keyword(s):  
Photocatalytic Oxidation ◽  
Removal Rate ◽  
Catalytic Degradation ◽  
Gas Chromatography Mass Spectrometry ◽  
Pharmaceutical Wastewater ◽  
High Concentration ◽  
Modified Attapulgite ◽  
Cod Removal Rate ◽  
Pre Treatment ◽  
Almost All

Chemical synthetic pharmaceutical wastewater has characteristics of high concentration, high toxicity and poor biodegradability, so it is difficult to directly biodegrade. We used acid modified attapulgite (ATP) supported Fe-Mn-Cu polymetallic oxide as catalyst for multi-phase Fenton-like ultraviolet photocatalytic oxidation (photo-Fenton) treatment with actual chemical synthetic pharmaceutical wastewater as the treatment object. The results showed that at the initial pH of 2.0, light distance of 20 cm, and catalyst dosage and hydrogen peroxide concentration of 10.0 g/L and 0.5 mol/L respectively, the COD removal rate of wastewater reached 65% and BOD5/COD increased to 0.387 when the reaction lasted for 180 min. The results of gas chromatography-mass spectrometry (GC-MS) indicated that Fenton-like reaction with Fe-Mn-Cu@ATP had good catalytic potential and significant synergistic effect, and could remove almost all heterocycle compounds well. 3D-EEM (3D electron microscope) fluorescence spectra showed that the fluorescence intensity decreased significantly during catalytic degradation, and the UV humus-like and fulvic acid were effectively removed. The degradation efficiency of the nanocomposite only decreased by 5.8% after repeated use for 6 cycles. It seems appropriate to use this process as a pre-treatment for actual pharmaceutical wastewater to facilitate further biological treatment.

The Photocatalytic Oxidation Properties of La3+-Doped and Ce4+-Doped ZnO-TiO2 in Treating Pharmaceutical Wastewater

2013 ◽  
Vol 726-731 ◽  
pp. 2988-2992
Author(s):  
Lei Zhu ◽  
Yang Fan Xiao ◽  
Xun Wang
Keyword(s):  
Photocatalytic Oxidation ◽  
Removal Rate ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Pharmaceutical Wastewater ◽  
X Ray ◽  
Chinese Patent Medicine ◽  
Chinese Patent ◽  
Oxidation Properties ◽  
Doping Ratio

This experiment aims to prepare the Zn2 +-doped TiO2 composite semiconductor materials by the sol-gel method and to characterize their crystal structures by X-ray diffraction and electron microscopy (SEM) scanning. The degradation target in this experiment is the pharmaceutical wastewater of a certain Chinese patent medicine, whose COD is as high as 300,000 mg/L and chroma is above 500 degrees. When the doping ratio of ZnO is 8%, the pharmaceutical wastewaters COD and chroma removal rates for 2hs degradation respectively reach 72.5% and 33.8%. The doping of Ce4+ or La3+ can improve the catalytic activity of ZnO-TiO2. The cerium doped in can improve ZnO-TiO2s catalytic property within 7%, and when the doping ratio of lanthanum is 0.4%, the chroma removal rate of the pharmaceutical wastewater reaches 65%, 31.2% more than that of the pure ZnO-TiO2.

scholarly journals Catalytic Ozonation for Effective Degradation of Coal Chemical Biochemical Tail Water by Mn/Ce@RM Catalyst

Water ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 206
Author(s):  
Yicheng Wang ◽  
Yingkun Wang ◽  
Xi Lu ◽  
Wenquan Sun ◽  
Yanhua Xu ◽  
...  
Keyword(s):  
Reaction Time ◽  
Removal Rate ◽  
Catalytic Ozonation ◽  
Operating Conditions ◽  
Cod Removal ◽  
X Ray ◽  
Initial Ph ◽  
Catalyst Dosage ◽  
Cod Removal Rate ◽  
Tail Water

An Mn/Ce@red mud (RM) catalyst was prepared from RM via a doping–calcination method. Scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy were used to characterize the surface morphology, crystal morphology, and elemental composition of the Mn/Ce@RM catalyst, respectively. In addition, preparation and catalytic ozonation conditions were optimized, and the mechanism of catalytic ozonation was discussed. Lastly, a fuzzy analytic hierarchy process (FAHP) was adopted to evaluate the degradation of coal chemical biochemical tail water. The best preparation conditions for the Mn/Ce@RM catalyst were found to be as follows: (1) active component loading of 3%, (2) Mn/Ce doping ratio of 2:1, (3) calcination temperature of 550 °C, (4) calcination time of 240 min, and (5) fly ash floating bead doping of 10%. The chemical oxygen demand (COD) removal rate was 76.58% under this preparation condition. The characterization results suggested that the pore structure of the optimized Mn/Ce@RM catalyst was significantly improved. Mn and Ce were successfully loaded on the catalyst in the form of MnO2 and CeO2. The best operating conditions in the study were as follows: (1) reaction time of 80 min, (2) initial pH of 9, (3) ozone dosage of 2.0 g/h, (4) catalyst dosage of 62.5 g/L, and (5) COD removal rate of 84.96%. Mechanism analysis results showed that hydroxyl radicals (•OH) played a leading role in degrading organics in the biochemical tail water, and adsorption of RM and direct oxidation of ozone played a secondary role. FAHP was established on the basis of environmental impact, economic benefit, and energy consumption. Comprehensive evaluation by FAHP demonstrated that D3 (with an ozone dosage of 2.0 g/H, a catalyst dosage of 62.5 g/L, initial pH of 9, reaction time of 80 min, and a COD removal rate of 84.96%) was the best operating condition.

Wet oxidation of an industrial high concentration pharmaceutical wastewater using hydrogen peroxide as an oxidant

2017 ◽  
Vol 20 (1) ◽  
Author(s):  
Xu Zeng ◽  
Jun Liu ◽  
Jianfu Zhao
Keyword(s):  
Hydrogen Peroxide ◽  
Removal Rate ◽  
Batch Reactor ◽  
Cod Removal ◽  
Evaluation Index ◽  
Wet Oxidation ◽  
Pharmaceutical Wastewater ◽  
High Concentration ◽  
Cod Removal Rate ◽  
Temperature Time

AbstractWet oxidation of an industrial pharmaceutical wastewater with high concentration organic pollutants using hydrogen peroxide as an oxidant was investigated. Experiments were performed in a batch reactor to discuss the effects of reaction temperature, time, the hydrogen peroxide amount and catalyst with COD removal rate as an evaluation index. Results show that the highest COD removal rate, 81.6 %, was achieved at 240 ºC for 60 min with the addition of H

scholarly journals Preparation and Application of Sewage Sludge Bio-char/zero Valent Iron (SSBC/ZVI) Composite for Improving the Biodegradability of a Real Chemical Synthesis-based Pharmaceutical Wastewater

2021 ◽  
Author(s):  
Gaoxiang Qi ◽  
Xiaobo Wang ◽  
Xuecheng Liu ◽  
Shen Yu
Keyword(s):  
Sewage Sludge ◽  
Chemical Synthesis ◽  
Removal Rate ◽  
Optimal Operation ◽  
Cod Removal ◽  
Pharmaceutical Wastewater ◽  
Operation Condition ◽  
Initial Ph ◽  
Cod Removal Rate ◽  
Pollutants Removal

Abstract A new kind of micro-electrolysis filler sewage sludge biochar/zero violent iron (SSBC/ZVI) composite was prepared for a real chemical synthesis based pharmaceutical wastewater (CSPW) pretreatment for improving the biodegradation index (BI). The optimal operation condition of micro-electrolysis system was obtained at HRT of 2 h, the initial pH of 3.0 and filler dosage of 100 g/L, with COD removal rate of 30.5%. Comparative analysis of raw and used SSBC/ZVI filler, GC-MS analysis of raw and treated pharmaceutical wastewater suggested that the pollutants removal was mainly attributed to the combination of reduction and oxidation, absorption of SSBC and flocculation effect of iron sludge. In addition, SSBC/ZVI exhibited relative high stability and excellent reusability for COD removal and BI improvement of real pharmaceutical wastewater. The results of this study provide new ideas of sewage sludge utilization for real wastewater pretreatment.

Cytomembrane Preservation in Tissue Dehydrated Only With Glutaraldehyde and Epon 812 Resin

1973 ◽  
Vol 31 ◽  
pp. 320-321
Author(s):  
Daniel C. Pease
Keyword(s):  
Diffraction Pattern ◽  
X Ray Diffraction ◽  
High Concentration ◽  
Unpublished Study ◽  
X Ray ◽  
Sectioned Material

A previous study demonstrated that tissue could be successfully infiltrated with 50% glutaraldehyde, and then subsequently polymerized with urea to create an embedment which retained cytomembrane lipids in sectioned material. As a result, the 180-190 Å periodicity characteristic of fresh, mammalian myelin was preserved in sections, as was a brilliant birefringence, and the capacity to bind OsO4 vapor in the hydrophobic bilayers. An associated (unpublished) study, carried out in co-operation with Drs. C.K. Akers and D.F. Parsons, demonstrated that the high concentration of glutaraldehyde (and urea) did not significantly alter the X-ray diffraction pattern of aldehyde-fixed, myelin. Thus, by itself, 50% glutaraldehyde has little effect upon cytomembrane systems and can be used with confidence for the first stages of dehydration.

scholarly journals Leaching Titaniferous Magnetite Concentrate by Alkaline Aqueous Solution

2021 ◽  
Author(s):  
Ke Guo ◽  
Shaoyan Wang ◽  
Renfeng Song ◽  
Zhiqiang Zhang
Keyword(s):  
Aqueous Solution ◽  
Alkali Concentration ◽  
Water Usage ◽  
X Ray Diffraction ◽  
High Concentration ◽  
X Ray ◽  
Iron Concentrate ◽  
Titaniferous Magnetite ◽  
Magnetite Concentrate ◽  
Kinetics Of

AbstractLeaching titaniferous magnetite concentrate with alkali solution of high concentration under high temperature and high pressure was utilized to improve the grade of iron in iron concentrate and the grade of TiO2 in titanium tailings. The titaniferous magnetite concentrate in use contained 12.67% TiO2 and 54.01% Fe. The thermodynamics of the possible reactions and the kinetics of leaching process were analyzed. It was found that decomposing FeTiO3 with NaOH aqueous solution could be carried out spontaneously and the reaction rate was mainly controlled by internal diffusion. The effects of water usage, alkali concentration, reaction time, and temperature on the leaching procedure were inspected, and the products were characterized by X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. After NaOH leaching and magnetic separation, the concentrate, with Fe purity of 65.98% and Fe recovery of 82.46%, and the tailings, with TiO2 purity of 32.09% and TiO2 recovery of 80.79%, were obtained, respectively.

Preparation of xanthated bentonite and its removal behavior for Pb(II) ions

2010 ◽  
Vol 61 (5) ◽  
pp. 1235-1243 ◽  
Author(s):  
Y. F. He ◽  
F. R. Li ◽  
R. M. Wang ◽  
F. Y. Li ◽  
Y. Wang ◽  
...  
Keyword(s):  
Adsorption Mechanism ◽  
Removal Rate ◽  
Freundlich Isotherm ◽  
Particle Size Analysis ◽  
Lead Ions ◽  
Size Analysis ◽  
Optimum Conditions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir

Xanthate was successfully grafted onto bentonite by a relatively simple solution reaction. The obtained xanthated bentonite (XBent) was characterized by FT-IR spectrophotometer, thermogravimetric analysis (TG), particle size analysis, x-ray diffraction (XRD) and scanning electron microscopy (SEM). XBent acting as a type of environmentally friendly adsorbent was applied to remove lead ions from aqueous solutions. The optimum conditions were as follows: [Pb2 + ] = 500 mg L−1, [XBent] = 2 g L−1, pH = 5.0; oscillating 60 min under 200 rpm at 25°C. The removal rate of lead was up to 99.9%. It was found that the lead(II) ions—XBent adsorption isotherm model fitted well to the Freundlich isotherm. The adsorption mechanism was also investigated by SEM and XRD, which concluded that lead ions were complexed or chelated with XBent. XBent appears to have potential to be used later in water treatment as a type of inorganic polymer reagent.

Isolation and characterization of lignocellulosic fiber from jute bast by the organic solvent degumming system: an alkali-free method

2021 ◽  
pp. 004051752110154
Author(s):  
Zhihui Qin ◽  
Shuyuan Zhao ◽  
Liu Liu ◽  
Zhaohe Shi ◽  
Longdi Cheng ◽  
...  
Keyword(s):  
National Standards ◽  
X Ray Diffraction ◽  
High Concentration ◽  
X Ray ◽  
Lignocellulosic Fibers ◽  
Lignocellulosic Fiber ◽  
Isolation And Characterization ◽  
Alkali Consumption ◽  
Scanning Electron

Degumming is the dominant method for insolating lignocellulosic fibers in textile applications. Traditional alkaline degumming (TAL), as a common method, requires a high-concentration alkali and has been a severe challenge to the environment. In the research reported here, the possibility of innovative jute degumming by organic solvents 1-2 propylene glycol and a combination of additive green oxygen (GO-OS) was studied. The results revealed that fibers could be extracted by this system (under condition of 0.9% GO-OS, 180°C, 120 min), and obtained fibers with higher breaking tenacity (7.1 cN/dtex), yield (65.7%), breaking elongation (2.87%) and residual gum (11.7%), which all meet the requirement of the relevant Chinese Textile National Standards. Notably, the required reaction time (120 min) of the GO-OS system was 180 min shorter than that of the TAL method. Furthermore, the modifications introduced by the degumming effect on physicochemical aspects were characterized and confirmed by Fourier transform infrared spectroscopy, scanning electron microscopy and X-ray diffraction. This study provides a promising degumming method for separating jute lignocellulose without acid and alkali consumption.

Characterization of New Nonstoichiometric Ferroelectric (Li0.95Cu0.15)Ta0.76Nb0.19O3 and Comparative Study With (Li0.95Cu0.15)Ta0.57Nb0.38O3 as Photocatalysts in Microbial Fuel Cells

2018 ◽  
Vol 16 (2) ◽  
Author(s):  
S. Louki ◽  
N. Touach ◽  
A. Benzaouak ◽  
V. M. Ortiz-Martínez ◽  
M. J. Salar-García ◽  
...  
Keyword(s):  
Power Density ◽  
Microbial Fuel Cells ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Ferroelectric Material ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Uv Visible

This work investigates the photocatalytic activity of new ferroelectric material with formula (Li0.95Cu0.15)Ta0.76Nb0.19O3 (LT76) in a single chamber microbial fuel cell (MFC) and compares its performance with the similar photocatalyst (Li0.95Cu0.15)Ta0.57Nb0.38O3 (LT57). The photocatalysts LT76 and LT57 were synthesized by ceramic route under the same conditions, with the same starting materials. The ratio Ta/Nb was fixed at 4.0 and 1.5 for LT76 and LT57, respectively. These phases were characterized by different techniques including X-ray diffraction (XRD), transmission electronic microscopy (TEM), particle size distribution (PSD), differential scanning calorimetry (DSC), and ultraviolet (UV)–visible (Vis). The new photocatalyst LT76 presents specific surface area of 0.791 m2/g and Curie temperature of 1197 °C. The photocatalytic efficiency of this material is assessed in terms of wastewater treatment and electricity generation by power density and removal rate of chemical oxygen demand (COD) in the presence of a light source. The values of maximum power density and COD removal were 19.77 mW/m3 and 93%, respectively, for LT76.

Sign in / Sign up

Export Citation Format

Share Document