scholarly journals Numerical modelling of water subsurface reservoirs during the operation phase in underground pumped storage hydropower plants

2020 ◽  
Vol 152 ◽  
pp. 02001
Author(s):  
Javier Menéndez ◽  
Jorge Loredo
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Static Pressure ◽  
Numerical Models ◽  
Water Flow Rate ◽  
Two Phase ◽  
Ventilation Shaft ◽  
Underground Reservoir ◽  
Operation Stage ◽  
Pumped Storage

Underground pumped storage hydropower (UPSH) plants may be an alternative to store subsurface energy with lower environmental impacts than conventional pumped storage hydropower (PSH) plants. Network of tunnels in closed mines (i.e. coal mines) could be used as water lower reservoir of UPSH plants. The amount of storable energy depends on the water mass and the net head between upper and lower reservoirs. Depending on the direction of the water flow rate, pumping or turbine modes may be used to produce or consume electrical energy. Filling and emptying processes during the operation stage in the underground reservoir are complicated due to the presence of two fluids (water and air) interacting inside the network of tunnels. This paper explores the underground reservoir during the operation stage considering a water flow rate of 55 m3s-1. Two-phase three dimensional CFD numerical models using Ansys Fluent have been developed in order to know the behaviour of the air flow on tunnels and ventilation shaft. Static pressure and air velocity have been analyzed in the simulations at the exit of the ventilation shaft as well as the junction zone between the ventilation shaft and the tunnels network. The results obtained show that a static pressure up to 8,600 Pa and air velocities up to 80 m s-1 could be reached in turbine mode considering a vent shaft with 1 m in diameter. The static pressure increases up to 258,000 Pa if a ventilation shaft of 0.5 m in diameter is considered.

Experimental Characterization of a Modified Airlift Pump

2014 ◽  
Author(s):  
Afshin Goharzadeh ◽  
Keegan Fernandes
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
High Speed ◽  
Water Flow Rate ◽  
High Speed Photography ◽  
Two Phase ◽  
Inner Diameter ◽  
Airlift Pump ◽  
Flow Map ◽  
Churn Flow

This paper presents an experimental investigation on a modified airlift pump. Experiments were undertaken as a function of air-water flow rate for two submergence ratios (ε=0.58 and 0.74), and two different riser geometries (i) straight pipe with a constant inner diameter of 19 mm and (ii) enlarged pipe with a sudden expanded diameter of 19 to 32 mm. These transparent vertical pipes, of 1 m length, were submerged in a transparent rectangular tank (0.45×0.45×1.1 m3). The compressed air was injected into the vertical pipe to lift the water from the reservoir. The flow map regime is established for both configurations and compared with previous studies. The two phase air-water flow structure at the expansion region is experimentally characterized. Pipeline geometry is found to have a significant influence on the output water flow rate. Using high speed photography and electrical conductivity probes, new flow regimes, such as “slug to churn” and “annular to churn” flow, are observed and their influence on the output water flow rate and efficiency are discussed. These experimental results provide fundamental insights into the physics of modified airlift pump.

Influences of Impeller Diameter and Diffuser Blades on Air-Water Two-Phase Flow Performance of Centrifugal Pump

2005 ◽  
Author(s):  
Naoki Matsushita ◽  
Akinori Furukawa ◽  
Kusuo Okuma ◽  
Satoshi Watanabe
Keyword(s):  
Centrifugal Pump ◽  
Water Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Flow Condition ◽  
High Performance ◽  
Two Phase Flow ◽  
Water Flow Rate ◽  
Phase Flow ◽  
Two Phase

A tandem arrangement of double rotating cascades and single diffuser cascade, proposed as a centrifugal pump with high performance in air-water two-phase flow condition, yields lower head due to the smallness of the impeller outlet in comparison with a impeller with large outlet diameter and no diffuser. Influences of impeller diameter change and installation of diffuser blades on two-phase flow performance were experimentally investigated under the case of the same volute casing. As the result, the similarity law of the diameter of impeller having the similar blade geometry and the rotational speed is satisfied even in two-phase flow condition. Comparing pump performances between a large impeller without diffuser blades and a small one with diffuser blades, higher two-phase flow performance is obtained by controlling the rotational speed of a small impeller with diffuser blades in the range of small water flow rates, while a large impeller with no diffuser gives high performance in the range of high water flow rate and small air flow rate.

Micro-scale simulation of bubble-water flow in coal seams by the lattice Boltzmann method

2016 ◽  
Vol 56 (2) ◽  
pp. 608
Author(s):  
Jie Yi ◽  
Huilin Xing ◽  
Tianwei Sun ◽  
Victor Rudolph
Keyword(s):  
Coal Seam ◽  
Water Flow ◽  
Flow Rate ◽  
Bubble Size ◽  
Lattice Boltzmann ◽  
Water Flow Rate ◽  
Bubble Flow ◽  
Coal Seam Gas ◽  
Two Phase ◽  
Flow Process

The production of coal seam gas initially requires pumping and removing significant amounts of water to sufficiently reduce the hydrostatic pressure in the subsurface, so that methane can desorb from the matrix and diffuse into the cleat systems; majority of the methane molecules gather into nucleation or bubbles. During the depression, the flow pattern of gas in cleats changes from bubble flow to slug flow, and finally forms circular flow. The significance of the bubble flow process—during which the liquid phase is continuous while the gas phase exists as small bubbles randomly distributed within the liquid—has not been emphasised because of its complexity. In this study, a free energy based two-phase lattice Boltzmann model is used to simulate the gas bubble/water flow behaviour in micro-cleats of a coal seam gas reservoir. The model was validated by comparison with analytical results based on dimensionless numbers, and good agreement was found in general. The influences of bubble shape, bubble size, and coal surface wettability on gas water two-phase flow in micro-cleats are discussed. The simulation results indicate that the bubble size and wettability of gas have significant impacts on the flow capacity of both gas and water. A decrease of the water flow rate is observed when large bubbles occur, and the gas flow rate decreases when the gas wettability becomes stronger. The bubble flow process significantly influences the drainage of water and the further gas production.

Development of Air/Water Two-Phase Flow Centrifugal Pump and Its Operating Characteristics

2003 ◽  
Author(s):  
Akinori Furukawa ◽  
Satoshi Ohshita ◽  
Kusuo Okuma ◽  
Satoshi Watanabe
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Two Phase Flow ◽  
Air Flow ◽  
Water Flow Rate ◽  
Phase Flow ◽  
Air Flow Rate ◽  
Operating Characteristics ◽  
Two Phase ◽  
Flow Pump

A centrifugal impeller, the pumping action of which could be highly kept even at an air-water two-phase flow condition of inlet void fraction more than 30% in the region of relatively high water flow rate, has been developed. In the present paper, the design concept of two-phase flow impeller is described, at first, with experimental results. The short bladed forward impeller with high outlet blade angle was decided to keep theoretical head higher even in two-phase flow condition and to disperse the air accumulating region on the suction blade surface by the water jet flow coming from the pressure side. Furthermore, the tandem arrangement of outer and inner rotating cascades with the same blade numbers was adopted to suppress the rotating stall phenomena appearing in the case of a single stage of outer cascade. It should be noted that these results were obtained with operating a boost pump installed upstream of mixing section of air and water, that is not an actual operation of two-phase flow pump. Secondly, the operating characteristics of this two-phase flow pump with change of air flow rate were investigated experimentally without operating the boost pump. As the trajectory of operating point with increasing air flow rate appears along the resistance curve of piping system, the impossibility of pumping occurs at lower air flow rate even though pump head takes a positive value at high air flow rate with increasing water flow rate. It is recognized that it is necessary to improve two-phase flow head characteristic curves in the region of low water flow rate to operate in wider two-phase flow conditions.

scholarly journals Effect of Water Flow on Underwater Wet Welded A36 Steel

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 682
Author(s):  
Eko Surojo ◽  
Aziz Harya Gumilang ◽  
Triyono Triyono ◽  
Aditya Rio Prabowo ◽  
Eko Prasetya Budiana ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Flow ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Physical And Mechanical Properties ◽  
Shielded Metal Arc Welding ◽  
Effect Of Water ◽  
Bending Effect ◽  
Metal Arc Welding ◽  
A36 Steel

Underwater wet welding (UWW) combined with the shielded metal arc welding (SMAW) method has proven to be an effective way of permanently joining metals that can be performed in water. This research was conducted to determine the effect of water flow rate on the physical and mechanical properties (tensile, hardness, toughness, and bending effect) of underwater welded bead on A36 steel plate. The control variables used were a welding speed of 4 mm/s, a current of 120 A, electrode E7018 with a diameter of 4 mm, and freshwater. The results show that variations in water flow affected defects, microstructure, and mechanical properties of underwater welds. These defects include spatter, porosity, and undercut, which occur in all underwater welding results. The presence of flow and an increased flow rate causes differences in the microstructure, increased porosity on the weld metal, and undercut on the UWW specimen. An increase in water flow rate causes the acicular ferrite microstructure to appear greater, and the heat-affected zone (HAZ) will form finer grains. The best mechanical properties are achieved by welding with the highest flow rate, with a tensile strength of 534.1 MPa, 3.6% elongation, a Vickers microhardness in the HAZ area of 424 HV, and an impact strength of 1.47 J/mm2.

scholarly journals Impacts of Water Flow Rate on Freezing Prevention of Air-Cooled Heat Exchangers in Power Plants

Energies ◽  
2018 ◽  
Vol 11 (1) ◽  
pp. 112 ◽  
Author(s):  
Yonghong Guo ◽  
Huimin Wei ◽  
Xiaoru Yang ◽  
Weijia Wang ◽  
Xiaoze Du ◽  
...  
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Power Plants ◽  
Water Flow Rate

scholarly journals Maximum Flow Rate of a Single Component, Two-Phase Mixture

1965 ◽  
Vol 87 (1) ◽  
pp. 134-141 ◽  
Author(s):  
F. J. Moody
Keyword(s):  
Flow Rate ◽  
Static Pressure ◽  
Maximum Flow ◽  
Single Component ◽  
Maximum Flow Rate ◽  
Vapor Flow ◽  
Two Phase ◽  
Slip Ratio ◽  
Phase Mixture ◽  
Local Slip

A theoretical model is developed for predicting the maximum flow rate of a single component, two-phase mixture. It is based upon annular flow, uniform linear velocities of each phase, and equilibrium between liquid and vapor. Flow rate is maximized with respect to local slip ratio and static pressure for known stagnation conditions. Graphs are presented giving maximum steam/water flow rates for: local static pressures between 25 and 3,000 psia, with local qualities from 0.01 to 1.00; local stagnation pressures and enthalpies which cover the range of saturation states.

Sign in / Sign up

Export Citation Format

Share Document