scholarly journals Numerical Simulation on Flow and Heat Transfer in Pulsating Heat Pipe with Different Models

2020 ◽  
Vol 165 ◽  
pp. 01031
Author(s):  
Jian-Hong Liu ◽  
Fu-Min Shang ◽  
Wei Qiao
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Pipe ◽  
Volume Fraction ◽  
Working Fluid ◽  
Gas Velocity ◽  
Pulsating Heat Pipe ◽  
Flow And Heat Transfer ◽  
Gas Volume Fraction ◽  
Gas Volume

Based on Mixture and Euler model, numerical simulation was used to study the flow and heat transfer in pulsating heat pipe by unsteady method. By comparing the gas volume fraction and gas velocity by different models at different time, the results showed that both models could simulate the evaporation and condensation process of the working fluid, and the liquid plug and gas plug were formed in the tube. By comparing the gas volume fraction and gas velocity at 5s and 10s, it was indicated that the fluid dynamics and heat transfer were more violent by Mixture model in the tube.

Thermal Performance of an Al2O3–Water Nanofluid Pulsating Heat Pipe

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Hamid Reza Seyf ◽  
Sejung Kim ◽  
Yuwen Zhang
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Volume Fraction ◽  
Numerical Study ◽  
Pure Water ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Liquid Slug ◽  
Temperature And Pressure ◽  
Vapor Temperature

A numerical study is performed to investigate the effects of nanofluids on the heat transfer performance of a pulsating heat pipe (PHP). Pure water is employed as the base fluid while Al2O3 with two different particle sizes, 38.4 and 47 nm, is used as nanoparticle. Different parameters including displacement of liquid slug, vapor temperature and pressure, liquid slug temperature distribution, as well as sensible and latent heat transfer in evaporator and condenser are calculated numerically and compared with the ones for pure water as working fluid. The results show that nanofluid has significant effect on heat transfer enhancement of the system and with increasing volume fraction and decreasing particles diameter the enhancement intensifies.

Numerical Study on Flow and Heat and Mass Transfer in Pulsating Heat Pipe

2019 ◽  
Author(s):  
Jian-Hong Liu ◽  
Fu-Min Shang ◽  
Nikolay Efimov
Keyword(s):  
Numerical Simulation ◽  
Mass Transfer ◽  
Heat Pipe ◽  
Gas Phase ◽  
Heat And Mass Transfer ◽  
Mixture Model ◽  
Volume Fraction ◽  
Pulsating Heat Pipe ◽  
Two Phase ◽  
Pipe Model

Abstract Numerical simulation was performed to establishing a two-dimensional pulsating heat pipe model, to investigate the flow and heat transfer characteristics in the pulsating heat pipe by using the Mixture and Euler models, which were unsteady models of vapor-liquid two-phase, based on the control-volume numerical procedure utilizing the semi-implicit method. Through comparing and analyzing the volume fraction and velocity magnitude of gas phase to decide which model was more suitable for numerical simulation of the pulsating heat pipe in heat and mass transfer research. It was showed there had gas phase forming in stable circulation flow in the heating section, the adiabatic section using the Mixture and Euler models respectively, and they were all in a fluctuating state at 10s, besides, the pulsating heat pipe had been starting up at 1s and stabilizing at 5s, it was all found that small bubbles in the heat pipe coalescing into large bubbles and gradually forming into liquid plugs and gas columns from the contours of volume fraction of the gas phase; through comparing the contours of gas phase velocity, it could be seen that there had further stably oscillating flow and relatively stabler gas-liquid two-phase running speed in the pulsating heat pipe used the Mixture model, the result was consistent with the conclusion of the paper[11] extremely, from this it could conclude that the Mixture model could be better simulate the vaporization-condensation process in the pulsating heat pipe, which could provide an effective theoretical support for further understanding and studying the phase change heat and mass transfer mechanism of the pulsating heat pipe.

Numerical Simulation and Innovative Structure of Drainage Cover

2018 ◽  
Author(s):  
Shengbiao Zhang ◽  
Zhandong Wang ◽  
Yan Yan ◽  
Guifang Sun ◽  
Zhonghua Ni
Keyword(s):  
Numerical Simulation ◽  
Laser Welding ◽  
Volume Fraction ◽  
3D Models ◽  
Fluid Simulation ◽  
High Similarity ◽  
Gas Volume Fraction ◽  
S Model ◽  
Gas Volume ◽  
Flow States

A fluid simulation was conducted on the flow states of water and drainage gas from the drainage cover in underwater local dry laser welding. The results of the simulation of gas volume fraction are obtained. Drainage cover was developed based on the drainage cover model. Experiments of drainage in this machined drainage cover was carried out, and were compared with the numerical simulation. The results show high similarity, which verifies the feasibility. Then, innovative structure featuring an uneven buffer around the exit of drainage cover are proposed to improve the performance of drainage. A group of 3D models of fluid domain related to differently characterized drainage covers was designed and the flow states were simulated. They are N-model with a narrow outlet, S-model with a smooth buffer added additionally based on N-model, U-model with an uneven buffer compared with S-model, and W-model with a wide outlet and the diameter of outlet twice than N-model. The gas volume fracture distributions were recorded and in comparison with each other. The results indicate that U-model with the uneven buffer realized the deepest drainage depth.

Operating Activity Visualization and Thermal Performance Measurement of Pulsating Heat Pipe

2016 ◽  
Vol 369 ◽  
pp. 42-47 ◽  
Author(s):  
Patrik Nemec ◽  
Zuzana Kolková ◽  
Milan Malcho
Keyword(s):  
Heat Transfer ◽  
Performance Measurement ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Vapour Phase ◽  
Working Fluid ◽  
Internal Diameter ◽  
Pulsating Heat Pipe ◽  
Inner Diameter ◽  
Thermo Physical Properties

Heat pipe is well known device which is used to heat transfer phase-change of working fluid. Pulsating heat pipe (PHP) is special type of heat pipe which heat transfer by pulsating movement of working fluid. Article deals about operating activity and thermal performance measurement of this special heat pipe. Operating activity visualization of PHP was performed with PHP made from glass. The two types of PHPs were made. The first PHP has internal diameter of tube 1 mm, second PHP has internal diameter of tube 1.5 mm and both PHPs have eleven meanders. The working fluids used in PHP were water and Fluorinert FC-72. These fluids were chose for their different thermo-physical properties and the visualization observe formation of liquid and vapour phase working fluid during filling process and working operation.Next, the article describes thermal performance measurement of PHP depending on working fluid amount and heat source temperature. Measurement was performed with PHP made from copper tube with inner diameter 1.5 mm curved to the twenty one meanders and filled with water. The results give us image about formation and distribution of working fluid in pulsating heat pipe and about influence of working fluid amount on the heat transfer ability of pulsating heat pipe.

Effects of Surface Coating of Nanoparticles on Thermal Performance of Open Loop Pulsating Heat Pipes

2012 ◽  
Author(s):  
Mehdi Taslimifar ◽  
Maziar Mohammadi ◽  
Ali Adibnia ◽  
Hossein Afshin ◽  
Mohammad Hassan Saidi ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Surface Coating ◽  
Heat Pipes ◽  
Open Loop ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Performance Of Heat Transfer

Homogenous dispersing of nanoparticles in a base fluid is an excellent way to increase the thermal performance of heat transfer devices especially Heat Pipes (HPs). As a wickless, cheap and efficient heat pipe, Pulsating Heat Pipes (PHPs) are important candidates for thermal application considerations. In the present research an Open Loop Pulsating Heat Pipe (OLPHP) is fabricated and tested experimentally. The effects of working fluid namely, water, Silica Coated ferrofluid (SC ferrofluid), and ferrofluid without surface coating of nanoparticles (ferrofluid), charging ratio, heat input, and application of magnetic field on the overall thermal performance of the OLPHPs are investigated. Experimental results show that ferrofluid has better heat transport capability relative to SC ferrofluid. Furthermore, application of magnetic field improves the heat transfer performance of OLPHPs charged with both ferrofluids.

Experimental Investigation of Heat Transfer of Refrigerant Fluid Pulsating Heat Pipe

2017 ◽  
Vol 865 ◽  
pp. 137-142
Author(s):  
Somchai Maneewan ◽  
Chantana Punlek ◽  
Hoy Yen Chan ◽  
Atthakorn Thongtha
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Temperature Difference ◽  
Heat Input ◽  
Filling Ratio ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Filling Volume ◽  
Volume Filling

Heat transfer performances of a pulsating heat pipe (PHP) having internal and external diameter with 4.5 mm and 6 mm with various contents of refrigerant are experimentally investigated. The working fluid as R404A refrigerant was filled in the volume ratios from 0% to 80% and the heat input was controlled in the range from 10 W to 80 W. Obtained results exhibited the ability of R404A refrigerant can enhance the thermal performance in steady state condition. The average temperature difference of the evaporating section and condensing section in the 80% filling volume ratio decreased from 9.5 °C to 2.5 °C when the heating power increase from 10 W to 80 W. The thermal resistance of evaporator and condenser decreased with an increase of the heat input as well. For other filling volume ratios, the trend of temperature difference and thermal resistance was similar to that of the 80% volume filling ratio. Considering the same heat input, the highest heat transfer performance was found at the 80% volume filling ratio. Refrigerant with a relatively low dynamic consistency can lead to relatively high velocity in the PHP that can reduce the temperature difference between the evaporating section and condensing section.

Modeling for Fluid Flow and Heat Transfer in Closed Loop Pulsating Heat Pipe

2020 ◽  
pp. 1-34
Author(s):  
Radhakanta Sarangi ◽  
Satya Prakash Kar ◽  
Abhilas Swain ◽  
Lalit Kumar Pothal
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Vapor Bubble ◽  
Closed Loop ◽  
Working Fluid ◽  
Vapour Bubble ◽  
Pulsating Heat Pipe ◽  
Time Step ◽  
Liquid Plug ◽  
Evaporation And Condensation

Abstract Numerical modelling of multi turn Closed Loop Pulsating Heat Pipe (CLPHP) is presented in this paper for ethanol as working fluid. Modelling is carried out for 1mm and 2mm ID PHP for different number of turns, different orientations and at constant wall temperature boundary conditions. Momentum and heat transfer variations with time are investigated numerically solving the one dimensional governing equations for vapor bubble and liquid plugs. Evaporation and condensation takes place by heat transfer through liquid film present around the vapour bubble. The code takes into account the realistic phenomena such as vapour bubble generation, liquid plug merging and super heating of vapor bubbles above its saturation temperature. During merging of liquid plugs, a time step adaptive scheme is implemented and this minimum time step was found to be 10−7 s. Nature of flow is investigated by momentum variation plot. Model results are compared with the experimental results from literature for nine different cases. Maximum variation in heat transfer for all these cases is found to be below ±34%. Keywords: Closed Loop Pulsating Heat Pipe, Liquid Plug, Plug momentum, Vapor Bubble, Heat Transfer, Thin Film Evaporation and Condensation

Sign in / Sign up

Export Citation Format

Share Document