scholarly journals Tensile strength of a vegetated and partially saturated soil

2020 ◽  
Vol 195 ◽  
pp. 03001
Author(s):  
Alessandro Fraccica ◽  
Enrique Romero ◽  
Thierry Fourcaud ◽  
Mercedes Sondon ◽  
Luis Gandarillas

Vegetated soil’s shear strength has been usually assessed through direct shear tests and under triaxial compression stress paths while less is known about its behaviour under tensile stress. Tensile strength and shrinkage-induced cracking play a crucial role in the hydro-mechanical response of earth structures exposed to drying/wetting cycles. For this purpose, a new device for direct tensile tests has been designed and used to let plants grow in compacted soil samples. The equipment consists of two cylindrical moulds connected to each other by a soil bridge in which failure upon pulling is induced due to geometrical constraints. Different soil’s mechanical responses were observed depending on whether suction was low or high. Indeed, it was detected an increase of soil tensile strength and a more brittle behaviour as suction was increasing. However, at the same suction, vegetated soil’s response was more ductile than that of the corresponding bare soil. Results were analysed within a shear strength criterion for partially saturated soils. The analysis evidenced an increase in shear strength in the vegetated soil. A correlation was found between this increase and the roots’ mechanical and morphological features.

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
Reza Noorzad ◽  
Seyed Taher Ghoreyshi Zarinkolaei

AbstractThis research investigates the behavior of sand reinforced with polypropylene fiber. To do this, 40 direct shear tests and 40 triaxial tests were performed on the coastal beaches of Babolsar, a city in the North of Iran. The effect of parameters such as fiber content, length of fiber and normal or confining pressure on the behavior of Babolsar sand have been studied. In this study, four various fiber contents (0, 0.25, 0.5 and 1 percent), three different lengths of fiber (6, 12 and 18 mm) and four normal or confining pressures (50, 100, 200 and 400 kPa) have been employed. The test results show that fiber inclusion has a significant effect on the behavior of sand. In both direct shear and triaxial tests, the addition of fibers improved shear strength parameters (C, '), increased peak shear strength and axial strain at failure, and also limited the amount of post-peak reduction in shear resistance. The comparison of the test results revealed that due to better fiber orientation toward the direction of principal tensile strain in triaxial test as compared to direct shear tests, the fiber efficiency and its effect on soil behavior is much more significant in triaxial specimens.


2020 ◽  
Vol 195 ◽  
pp. 01007
Author(s):  
Anil Yildiz ◽  
Frank Graf ◽  
Sarah M. Springman

Vegetation, particularly roots, serves different functions in relation to increased shear strength under saturated and partially saturated conditions. Quantification of mechanical contribution of roots due to their tensile strength, and relationships of various vegetation parameters and plant-induced suction, as well as shear strength, have been widely studied. Although shear strength is directly related to the volume change characteristics of soil, dilative or contractive behaviour of root-permeated soils has not been of significant interest so far. This study investigates how volume change during shearing is related to the hydrological and mechanical characteristics of vegetated soils relevant to slope stability and shear strength of root-permeated soils under partially saturated conditions. Direct shear tests, on specimens planted with a mixture of species from different plant functional groups, were performed with an Inclinable Large-scale Direct Shear Apparatus (ILDSA). Matric suctions were monitored throughout the test with tensiometers. Vertical and horizontal displacement graphs were plotted to investigate the volume change behaviour. Maximum dilatancy angle was found to be positively correlated with plant-induced suction and net normalised stress, both of which were linked to root biomass and the root:shoot ratio. It was found that maximum dilatancy is controlled by matric suction and net normal stress.


2021 ◽  
Author(s):  
Alessandro Fraccica ◽  
Enrique Romero ◽  
Thierry Fourcaud

<p>Soil tensile strength plays an important role in the hydro-mechanical behaviour of earth structures and slopes interacting with the atmosphere. Shrinkage-induced cracking may be generated by drying/wetting cycles, with consequent faster water infiltration from the top of slopes and reduction of the safety factor. Vegetation roots were proven to increase soil shear strength, but less is known about their effects on soil tensile strength. For this purpose, new equipment has been designed and used to induce plant growth in compacted soil samples and to perform uniaxial tensile tests on the reinforced material. The equipment is composed of two cylindrical moulds linked by a soil bridge in which the tensile crack is induced due to geometrical restraints.</p><p>For this study, silty sand was chosen and compacted at a low dry density (ρ<sub>d</sub> = 1.60 Mg/m<sup>3</sup>) and at a water content w = 15%. After compaction, samples were gently poured with water up to a high degree of saturation (S<sub>r</sub> ≈ 0.95) and low suction (s ≈ 1 kPa). Then, six of them were seeded with Cynodon dactilon, adopting fixed seeding density and spacing. Plants were irrigated and let to grow for three months: during this period, suction was monitored by a tensiometer. Seven fallow specimens were prepared following the same procedure, for comparison purposes.</p><p>When ready, samples were dried in a temperature/relative humidity-controlled room and left in the darkness for three hours, to attain and equalise the desired value of initial suction. Finally, the tensile stress was induced on the soil by a displacement rate of 0.080 mm/min. For each test, suction was continuously monitored by a tensiometer while the water content was checked at the beginning and at the end. Moreover, the void ratio and the root volume and area ratio were assessed close to the crack generated, at the end of each test.</p><p>The hydraulic state affected the soil mechanical response upon uniaxial extension: an increase of strength and a more brittle behaviour were observed as suction was increasing. At the same suction, a higher strength was systematically observed in the vegetated soil. In fact, even at very low suction (i.e. s = 1 kPa), vegetation roots induced a considerable increase in soil tensile strength (i.e. 10 kPa). The soil hydraulic state also affected the root failure mechanism. In wet soil, the roots subjected to tension were stretched and pulled-out whereas in dry soil they experienced a more immediate breakage (i.e. in concomitance with the cracking of the surrounding soil). Some preliminary PIV (Particle Image Velocimetry) analyses showed differences among dry/wet and fallow/vegetated soils. Indeed, a more diffuse strain field was observed in vegetated samples, thanks to the redistribution of stresses induced by the roots.</p><p>Results were successfully interpreted by a well-established shear strength criterion for partially saturated soils, considering the degree of saturation, suction and soil microstructure. An increase of the soil shear strength was observed and correlated to the presence of roots and to their geometrical and mechanical features. Moreover, good consistency was detected with results coming from other equipment.</p><p> </p>


2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Jianwen Ding ◽  
Xusong Feng ◽  
Yupeng Cao ◽  
Sen Qian ◽  
Feng Ji

Consolidated undrained triaxial compression tests were performed to investigate the shear strength behavior of the solidified dredged materials (SDM). The variation law of deviator stress and excess pore water pressure with the increase of the applied confining pressure was investigated. It is found that the shear strength envelope is consisted of two lines, and there exists a transitional stress on the intersection point. The undrained shear strength develops slightly with the increase of applied normal stress in the preyield state. However, the undrained shear strength increases significantly in the postyield state, and the strength envelope is nearly a straight line with the extension through the origin. Based on the triaxial test data and the binary medium model, a strength criterion considering strength evolution mechanism is proposed and the relevant parameters of the strength criterion were discussed. Comparisons of the predicted results and experimental data demonstrate that the proposed strength criterion can properly describe the strength evolution rules of the SDM.


2014 ◽  
Vol 580-583 ◽  
pp. 659-664
Author(s):  
Osvaldo de Freitas Neto ◽  
Olavo Francisco dos Santos Jr. ◽  
Ricardo Nascimento Flores Severo

This article aims at assessing the influence of relative density on the hydraulic conductivity and shear strength of two sands, denominated S01 and S02, derived from different regions and formation processes. S01 is wind-blown and S2 alluvial. The results of characterization and hydraulic conductivity in constant head tests were presented for both samples. The results of direct shear tests with sand S01 prepared with 5 different void ratios were also presented, for a vertical stress of 100kPa. The S02 sample was prepared with 4 different void ratios and these underwent direct shear testing with vertical stresses of 25kPa and 150kPa. This sample was prepared with the maximum and minimum void ratio and submitted to strength tests at CD triaxial compression with confining stresses of 50kPa, 100kPa and 200kPa. Results showed that even with different grain sizes, and under different density conditions, there were no significant variations in the permeability of the materials. With respect to shear strength, sand S01 obtained higher angle of friction values than sand S02, even though the latter had a higher percent coarse fraction. Sand S02 was relatively similar in terms of friction angle values obtained in direct shear and triaxial compression strength tests.


2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Jie Yang ◽  
Xin Cai ◽  
Qiong Pang ◽  
Xing-wen Guo ◽  
Ying-li Wu ◽  
...  

An experimental study on the shear strength development of cement-sand-gravel (CSG) material was carried out using triaxial compression tests. The effects of the cementing agent content, aggregate content, and gradation on the shear strength of CSG material were analyzed. The shear strength remarkably increased with increasing cementing agent content and aggregate content for a given confining pressure. The increase in shear strength with increasing cementing agent content far exceeded that with increasing aggregate content. However, the stress-strain curves and shear strength changed only slightly when the aggregate gradation for CSG material was adjusted. Based on the test data, a strength criterion for CSG material is proposed as a function of the cementing agent content, aggregate content, and shear strength of the aggregate gradation.


2018 ◽  
Vol 4 (11) ◽  
pp. 2787
Author(s):  
Baitollah Badarloo ◽  
Amir Kari ◽  
Faezeh Jafari

As one of the most widely used materials in different structures, concrete is a material evaluated and categorized based on compressive strength criterion. In addition, national and international codes (INBC- part 9) and standards determine the tensile strength of concrete based on its compressive strength. The purpose of this research is to determine the relationship between compressive strength and tensile strength of C20, C30 and C40 grades. In this laboratory research, a total of 42 cubic specimens of 150 × 150 × 150 mm and 42 cylindrical specimens of 300 × 150 mm were assessed under compressive and tensile tests, respectively. Based on the results of this study, the relationships presented in Ninth Article of Iranian National Building Codes, ACI-318 and Euro Code 2 have been evaluated.


2020 ◽  
Vol 2020 ◽  
pp. 1-13 ◽  
Author(s):  
H. Cai ◽  
R. Wei ◽  
J. Z. Xiao ◽  
Z. W. Wang ◽  
J. Yan ◽  
...  

In this paper, three different rock-soil mixtures were reconstituted in laboratory, which were designed to mimic the proportions of coarse and fine particles in the high fill used at the airport construction sites. The shear strength of the reconstituted mixtures was determined by both large-scale direct shear tests (DSTs) with different plate opening sizes and triaxial compression tests. By comparing the test results, the most appropriate plate opening size for DSTs on coarse gap-graded rock-soil mixtures is discussed. The test results indicate that the opening size has a significant effect on the measured shear strength of gap-graded rock-soil mixtures. For DSTs under the same normal stress, the peak strength decreases with increasing plate opening size. For the gap-graded mixture with a small proportion of coarse particles, a plate opening size of one-third to one-quarter of the maximum particle size (dmax) is suitable. With a higher coarse particle content, the opening size should be increased appropriately. If the percentage of gravels (5.0 mm < d < 20.0 mm) is more than 47%, a plate opening size of slightly greater or less than one-half dmax is more appropriate.


2021 ◽  
Author(s):  
Julian Ehrler ◽  
Alexander Solodov ◽  
Yannick Bernhardt ◽  
Marc Kreutzbruck

Abstract The nonlinear acoustic approach is assessed for applications as a nondestructive tool for reconstructing stress-strain curves and quantifying the ultimate tensile strength for variety of materials. The direct algorithm uses the polynomial stress-strain expansion up to the third power of strain and the literature data on the second-order nonlinearity parameters to calculate relevant segments of the stress-strain curves. Since the third-order nonlinearity parameters are unknown for majority of materials the calculations used an iteration scheme to obtain closer approximations to the experimental data available from static tensile tests. The solution to the inverse problem identifies the range of the nonlinearity parameters for a given tensile strength and enables to categorize the contribution of the quadratic and cubic nonlinearities in mechanical response for different materials.


Sign in / Sign up

Export Citation Format

Share Document