Vegetation effects on the tensile strength of a partially saturated soil

Author(s):  
Alessandro Fraccica ◽  
Enrique Romero ◽  
Thierry Fourcaud

<p>Soil tensile strength plays an important role in the hydro-mechanical behaviour of earth structures and slopes interacting with the atmosphere. Shrinkage-induced cracking may be generated by drying/wetting cycles, with consequent faster water infiltration from the top of slopes and reduction of the safety factor. Vegetation roots were proven to increase soil shear strength, but less is known about their effects on soil tensile strength. For this purpose, new equipment has been designed and used to induce plant growth in compacted soil samples and to perform uniaxial tensile tests on the reinforced material. The equipment is composed of two cylindrical moulds linked by a soil bridge in which the tensile crack is induced due to geometrical restraints.</p><p>For this study, silty sand was chosen and compacted at a low dry density (ρ<sub>d</sub> = 1.60 Mg/m<sup>3</sup>) and at a water content w = 15%. After compaction, samples were gently poured with water up to a high degree of saturation (S<sub>r</sub> ≈ 0.95) and low suction (s ≈ 1 kPa). Then, six of them were seeded with Cynodon dactilon, adopting fixed seeding density and spacing. Plants were irrigated and let to grow for three months: during this period, suction was monitored by a tensiometer. Seven fallow specimens were prepared following the same procedure, for comparison purposes.</p><p>When ready, samples were dried in a temperature/relative humidity-controlled room and left in the darkness for three hours, to attain and equalise the desired value of initial suction. Finally, the tensile stress was induced on the soil by a displacement rate of 0.080 mm/min. For each test, suction was continuously monitored by a tensiometer while the water content was checked at the beginning and at the end. Moreover, the void ratio and the root volume and area ratio were assessed close to the crack generated, at the end of each test.</p><p>The hydraulic state affected the soil mechanical response upon uniaxial extension: an increase of strength and a more brittle behaviour were observed as suction was increasing. At the same suction, a higher strength was systematically observed in the vegetated soil. In fact, even at very low suction (i.e. s = 1 kPa), vegetation roots induced a considerable increase in soil tensile strength (i.e. 10 kPa). The soil hydraulic state also affected the root failure mechanism. In wet soil, the roots subjected to tension were stretched and pulled-out whereas in dry soil they experienced a more immediate breakage (i.e. in concomitance with the cracking of the surrounding soil). Some preliminary PIV (Particle Image Velocimetry) analyses showed differences among dry/wet and fallow/vegetated soils. Indeed, a more diffuse strain field was observed in vegetated samples, thanks to the redistribution of stresses induced by the roots.</p><p>Results were successfully interpreted by a well-established shear strength criterion for partially saturated soils, considering the degree of saturation, suction and soil microstructure. An increase of the soil shear strength was observed and correlated to the presence of roots and to their geometrical and mechanical features. Moreover, good consistency was detected with results coming from other equipment.</p><p> </p>

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Yanlong Li ◽  
Zili Wang ◽  
Yang Luo

Shear strength of shallow expansive soil varies along with the depth under the freeze-thaw effect. This work investigates shear strength characteristics of shallow expansive soil by simulating the actual freeze boundary conditions of seasonal frozen areas with water supplement. An integrated approach incorporating the freeze-thaw test and direct shear test was adopted. Firstly, unidirectional freezing tests for expansive soil columns under three different freezing temperature gradients were carried out. Secondly, direct shear tests under low vertical stress were performed on the standard samples, which were prepared by using cutting rings cut the thawed expansive soil columns into nine segments along with the depth. Temperature, water content, and dry density at different depths were also investigated after the freeze-thaw process. The test results showed that, after the freeze-thaw process, the shear strength of expansive soil columns showed significant differences along with the depth and highly correlated with water content, specifically the higher water content and the lower shear strength. The minimum shear strength in the expansive soil columns occurred at the soil layer below the frozen and unfrozen zones interface. The expansive soil column’s shear strength changed most under the moderate freezing temperature gradient corresponding to the most considerable shear strength reduction. Moreover, the significant decrease in cohesion was the main reason for the shear strength reduction of expansive soil after the freeze-thaw process. These results indicate significant depth variability in shear strength of expansive soil under the freeze-thaw effect.


2020 ◽  
Vol 195 ◽  
pp. 03008
Author(s):  
Carmen Covadonga Garcia-Fernandez ◽  
Rafaela Cardoso ◽  
Martina Inmaculada Alvarez-Fernandez ◽  
Celestino Gonzalez-Nicieza

Cracking due to desiccation can compromise the behaviour of earth structures built with compacted clayey soils by promoting water access and consequent volume changes on further wetting. Tensile strength therefore is important to be considered when studying the behaviour of such structures, and in particular its dependence on the degree of saturation or water content. The influence of water content in tensile behaviour of compacted marls was investigated by performing diametral compression tests (Brazilian splitting tests), where axial deformations were measured besides strength. The samples were prepared by compaction at optimum point using standard compaction energy (optimum water content 16%) and then dried by vapour equilibrium to reach water contents between 5% and 16%. The correspondence between water content and suction was done by using the drying branch of the water retention curve, measured using WP4 equipment (Water Dewpoint Potentiometer). Good relationships were found between tensile strength and the water content (and suction). In addition, the study was completed with the analysis of other parameters such as the semi-contact angle created in the loaded area and the stiffness of the material, which also showed changes with water content.


2019 ◽  
Vol 24 (2) ◽  
pp. 113
Author(s):  
Paravita Sri Wulandari ◽  
Daniel Tjandra

Reservoir is needed as a source of water supply to the surrounding populations. The design of a reservoir needs to consider several aspects of soil embankment such as variations in water content and changes in shear soil shear strength and also the influence of water level in reservoir. The purpose of this research is to analyze these three aspects in the design of a reservoir. This research was begun by taking soil samples for embankment and conducting soil tests to obtain soil characteristics at the initial condition. The further laboratory tests were conducted to determine the effect of changes in water content on the shear strength of the soil. The variation of soil embankment characteristic was then modeled by Plaxis 2D program to obtain the effect of changes in soil embankment characteristic and fluctuation of the water level in the reservoir. The results showed that the increase in water content significantly decrease the shear strength of the soil. The changes of soil shear strength affect the pattern of slope failure and safety factor. In addition, the pattern and direction of the slope failure were also influenced by the water level of the reservoir.


2020 ◽  
Vol 195 ◽  
pp. 03031
Author(s):  
Omar AL-Emami ◽  
Gabriela M Medero ◽  
Fernando A M Marinho ◽  
Melis Sutman

Shear strength of soils is one of the essential parameters for analysing and solving divers geotechnical problems (e.g. the bearing capacity of shallow footings pile foundations, slope stability and earth embankments). In this study, a series of conventional large-scale (300 X 300 mm) direct shear tests were carried out on saturated and constant water content silty sand specimens at ei = 0.6 and 1.0 tested under applied vertical stresses of 100, 200, or 400 kPa to investigate the influence of matric suction on the shear strength characteristics of the tested material. A loading steel cap was modified to allow the direct measurements of the matric suction using two commercial available Equitensiometer suction probes (EQ3). The experimental program indicated that, for both studied void ratios, the obtained shear strength of specimens under constant water content is found to be distinctly greater than those obtained from saturated samples. The results showed that the samples compacted at ei = 1.0 exhibited collapse behaviour during saturation stage, whereas same samples did not show any volume change during stabilisation stage when tested under constant water content condition. The study results also showed that the matric suction reduction during consolidation stage depends on initial void ratio of the tested samples as well as the level of applied vertical stress. Moreover, the matric suction evolution during shearing process of both studied void ratios specimens decreased with increasing the level of applied vertical stress.


Author(s):  
Zhenning Yang ◽  
Carlton L. Ho ◽  
Richard Joy ◽  
Nandan C. Dabhade

The water content of fouled ballast is important when considering the shear strength and deformability of the ballast, and therefore critical in evaluating whether the track is at risk of excessive deformations warranting a speed restriction order. Fouled ballast from northeastern United States was tested in the laboratory to assess changes in shear strength and deformability as a function of water content. X-ray fluorescence analysis determined that the fouling material was 95% by weight basalt in origin. No more than 5% of the fouling material could be attributed to the abraded concrete ties. The field capacity of the fouled ballast was measured to be at a water content of 10%. Freezing and thawing tests indicated that approximately 4% of mass loss could be expected as a result of 25 freeze/thaw cycles. 6-inch triaxial tests, TX-CIDC, were conducted on the ballast at water contents between dry and field capacity (10%). As the ballast was partially saturated, volume change was measured using circumferential string potentiometers. The water content had an influence on the shear strength and the modulus of elasticity of the fouled ballast. The Mohr-Coulomb friction angle decreased from 47.3° for the dry ballast to 42.5° for the field capacity ballast. The Mohr-Coulomb cohesion decreased from 3.38 psi to nearly zero with initial addition of water, but increased to 6.18 psi as the water content reached field capacity. This is likely attributable to changes in capillary tension of the partially saturated fouling material. The average shear strength, Mohr-Coulomb friction angle, Mohr-Coulomb cohesion, modulus of elasticity and Poisson’s Ratio all showed weakening and strengthening effect by addition of water.


2012 ◽  
Vol 446-449 ◽  
pp. 1627-1632
Author(s):  
Qian Dong ◽  
Liu Liu ◽  
Long Hou

In order to research matrix suction how to influence the shear strengt of unsaturated silty sand. Based on the analysis of the Soil-water characteristic of unsaturated silty sand through pressure plate instrument test,the suction control direct shear tests under the different suction condition of unsaturated silty sand are studied. And then, the microscopic structure of two kinds soil sample with different water content are scanned to analyze the relationship between the matrix suction and the shear strengt of unsaturated silty sand. The results of the research show that unsaturated silty sand different from unsaturated clayey soil.When water content gradually reduce, the soil shear strength of unsaturated silty sand is not always increased with the increase of matrix suction, but there is a "peak effect".The appearance of "peak effect" is due to unsaturated silty sand has own microstructure characteristics.On the other hand, when the moisture content reduction constantly,the existence form of moisture change gradually.The two factors lead to the effect area of matrix suction change constantly,and then influence shear strengt of unsaturated silty sand to appear "peak effect". In addition,the stress environment also can influence contribution degree of matrix suction to the shear strengt of unsaturated silty sand.


2019 ◽  
Vol 92 ◽  
pp. 18002 ◽  
Author(s):  
Fumio Tatsuoka ◽  
Toru Miura

For satisfactory performance of soil structures, it is necessary to properly control soil compaction ensuring the physical properties of compacted soil required in design. Usually the dry density ρd and the water content w are controlled in relation to the maximum dry density (ρd)max and the optimum water content wopt determined by laboratory compaction tests on a chosen representative sample at a certain compaction energy level CEL. Although CEL and soil type affect significantly (ρd)max, wopt and physical properties, they change inevitably, sometimes largely, in a given project while field CEL may not match the value used in the laboratory compaction tests. In comparison, the optimum degree of saturation (Sr)opt (i.e., Sr when (ρd)max is obtained) and the normalized compaction curve (i.e., ρd/(ρd)max vs. Sr - (Sr)opt relation) for given CEL and soil type are insensitive to variations in CEL and soil type and they are essentially fixed in a given project. Besides, the stress-strain and hydraulic properties of compacted soil are controlled by ρd and “Sr at the end of compaction relative to (Sr)opt”. It is proposed to control w and CEL so that Sr= (Sr)opt while ρd becomes large enough to ensure the physical properties required in design fully taking advantage of available field CEL on site. A case history of earth-fill dam construction in Japan following this soil compaction control method is reported.


2012 ◽  
Vol 212-213 ◽  
pp. 108-112 ◽  
Author(s):  
Wen Sheng Dong ◽  
Xiu Fang Jiang ◽  
Xian Feng He ◽  
Ying Ying Zai

Aim to the high sandy river “ripping up the riverbed” phenomenon, by experiment, analyzing the relationship between clay dry density, water content, plasticity index and its shear strength, and its mechanical properties. Create the conditions for studying clay mechanical strength and the critical condition of “bottom tearing scour”.


2008 ◽  
Vol 305 (1-2) ◽  
pp. 207-226 ◽  
Author(s):  
S. De Baets ◽  
J. Poesen ◽  
B. Reubens ◽  
K. Wemans ◽  
J. De Baerdemaeker ◽  
...  

2012 ◽  
Vol 512-515 ◽  
pp. 1905-1918
Author(s):  
Yu Xian Shao ◽  
Bin Shi ◽  
Chun Liu ◽  
Lei Gao

Temperature significantly influences the engineering properties of clayey soil and this temperature effect usually depends on soil type. In this investigation, laboratorial experiments were conducted on three soils to evaluate the adsorbed water content, Atterberg limits, swelling, shear strength and permeability under different temperatures (5-50°C). The results indicate that liquid limit decreases, swelling increases, permeability increases with increasing temperature. It is fundamentally due to the change of adsorbed water content. Hydrophilic minerals, which contain large amounts of adsorbed water, play an important role in the temperature effect. With the increase of hydrophilic minerals, the temperature effect on liquid limit increases and the effect on swelling ratio decreases. The hydrophilic minerals content also has significant impact on the temperature effect of permeability. With increasing temperature, the adsorbed water is transformed to free water, and then the permeability may increase significantly. The shear strength of clayey soils with higher content of hydrophilic mineral is more sensitive to temperature variation. The cohesive force mainly changes linearly with the temperature. Different phenomena, i.e. thermal-hardening or thermal-softening, was observed on strength behaviour due to different hydrophilic mineral content, moisture content and dry density of sample.


Sign in / Sign up

Export Citation Format

Share Document