scholarly journals Hydraulic transport regimes of grains in a millifluidic confinement

2021 ◽  
Vol 249 ◽  
pp. 09013
Author(s):  
Guillaume Dumazer ◽  
Étienne Gagnepain
Keyword(s):  
Image Analysis ◽  
Pressure Drop ◽  
Granular Matter ◽  
Experimental Setup ◽  
Hydraulic Transport ◽  
Predictive Tool ◽  
Pressure Drops ◽  
Transport Regime ◽  
Key Features ◽  
Conveying System

Granular matter transported by hydraulic conveying behaves under several transport regimes. The techncal challenge is to predict the dilute or dense regime of transport as well as the pressure drop required in order to design properly a granular hydraulic conveying system. We address this problem with a laboratory scale experimental setup able to reproduce the key features of hydraulic conveying of grains. Pressure drop measurements as well as image analysis have been used to characterize a slug transport regime and its crossover towards a moving bed transport regime. A dimensionless characteristic curves diagram has been established and a reasonably good pressure drop prediction with a generic power law is explained in details. This preliminary work has the potential to open perspectives for the design of a predictive tool for pressure drops in hydraulic conveying systems.

Experimental and Computational Analyses of Pressure Differentials in Flexible Ducts With Different Bent Angles

2007 ◽  
Author(s):  
Ray R. Taghavi ◽  
Wonjin Jin ◽  
Mario A. Medina
Keyword(s):  
Pressure Drop ◽  
Static Pressure ◽  
Complex Geometry ◽  
Analysis Data ◽  
Secondary Flows ◽  
Low Flow ◽  
Pressure Drops ◽  
Pressure Distributions ◽  
Geometrical Effects ◽  
Cfd Analyses

A set of experimental analyses was conducted to determine static pressure drops inside non-metallic flexible, spiral wire helix core ducts, with different bent angles. In addition, Computational Fluid Dynamics (CFD) solutions were performed and verified by comparing them to the experimental data. The CFD computations were carried out to produce more systematic pressure drop information through these complex-geometry ducts. The experimental setup was constructed according to ASHRAE Standard 120-1999. Five different bent angles (0, 30, 45, 60, and 90 degrees) were tested at relatively low flow rates (11 to 89 CFM). Also, two different bent radii and duct lengths were tested to study flexible duct geometrical effects on static pressure drops. FLUENT 6.2, using RANS based two equations - RNG k-ε model, was used for the CFD analyses. The experimental and CFD results showed that larger bent angles produced larger static pressure drops in the flexible ducts. CFD analysis data were found to be in relatively good agreement with the experimental results for all bent angle cases. However, the deviations became slightly larger at higher velocity regimes and at the longer test sections. Overall, static pressure drop for longer length cases were approximately 0.01in.H2O higher when compared to shorter cases because of the increase in resistance to the flow. Also, the CFD simulations captured more pronounced static pressure drops that were produced along the sharper turns. The stronger secondary flows, which resulted from higher and lower static pressure distributions in the outer and inner surfaces, respectively, contributed to these higher pressure drops.

Experimental Study of Evaporation Heat Transfer Characteristics and Pressure Drops of R410A and R134a in a Multiport Mini-Channel

2009 ◽  
Author(s):  
Jatuporn Kaew-On ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients ◽  
Evaporation Heat ◽  
Evaporation Heat Transfer ◽  
R 134A

The evaporation heat transfer coefficients and pressure drops of R-410A and R-134a flowing through a horizontal-aluminium rectangular multiport mini-channel having a hydraulic diameter of 3.48 mm are experimentally investigated. The test runs are done at refrigerant mass fluxes ranging between 200 and 400 kg/m2s. The heat fluxes are between 5 and 14.25 kW/m2, and refrigerant saturation temperatures are between 10 and 30 °C. The effects of the refrigerant vapour quality, mass flux, saturation temperature and imposed heat flux on the measured heat transfer coefficient and pressure drop are investigated. The experimental data show that in the same conditions, the heat transfer coefficients of R-410A are about 20–50% higher than those of R-134a, whereas the pressure drops of R-410A are around 50–100% lower than those of R-134a. The new correlations for the evaporation heat transfer coefficient and pressure drop of R-410A and R-134a in a multiport mini-channel are proposed for practical applications.

Swirling Annular Flow in a Steam Separator

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Hironobu Kataoka ◽  
Yusuke Shinkai ◽  
Shigeo Hosokawa ◽  
Akio Tomiyama
Keyword(s):  
Pressure Drop ◽  
Annular Flow ◽  
Nuclear Reactor ◽  
Water Pressure ◽  
Interfacial Friction ◽  
Pressure Drops ◽  
Pressure Transducers ◽  
Ring Configuration ◽  
Film Flows ◽  
Steam Separator

Effects of pick-off ring configuration on the separator performance of a downscaled model of a steam separator for a boiling water nuclear reactor are examined using various types of pick-off rings. The experiments are conducted using air and water. Pressure drops in a barrel and a diffuser and diameters and velocities of droplets at the exit of the barrel are measured using differential pressure transducers and particle Doppler anemometry, respectively. The separator performance does not depend on the shape of the pick-off ring but strongly depends on the width of the gap between the pick-off ring and the barrel wall. The pressure drop in the barrel is well evaluated using the interfacial friction factor for unstable film flows. Carry-under can be estimated using a droplet velocity distribution at the exit of the separator.

Shellside Waterflow Pressure Drop Distribution Measurements in an Industrial-Sized Test Heat Exchanger

1988 ◽  
Vol 110 (1) ◽  
pp. 60-67 ◽  
Author(s):  
H. Halle ◽  
J. M. Chenoweth ◽  
M. W. Wambsganss
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Operating Cost ◽  
Power Requirement ◽  
Pressure Drops ◽  
Pressure Losses ◽  
Finned Tubes ◽  
Heat Exchanger Design ◽  
Isothermal Water

Throughout the life of a heat exchanger, a significant part of the operating cost arises from pumping the heat transfer fluids through and past the tubes. The pumping power requirement is continuous and depends directly upon the magnitude of the pressure losses. Thus, in order to select an optimum heat exchanger design, it is is as important to be able to predict pressure drop accurately as it is to predict heat transfer. This paper presents experimental measurements of the shellside pressure drop for 24 different segmentally baffled bundle configurations in a 0.6-m (24-in.) diameter by 3.7-m (12-ft) long shell with single inlet and outlet nozzles. Both plain and finned tubes, nominally 19-mm (0.75-in.) outside diameter, were arranged on equilateral triangular, square, rotated triangular, and rotated square tube layouts with a tube pitch-to-diameter ratio of 1.25. Isothermal water tests for a range of Reynolds numbers from 7000 to 100,000 were run to measure overall as well as incremental pressure drops across sections of the exchanger. The experimental results are given and correlated with a pressure drop versus flowrate relationship.

scholarly journals Grid convergence study of a cyclone separator using different mesh structures

2017 ◽  
Vol 23 (3) ◽  
pp. 311-320 ◽  
Author(s):  
R.A.F. Oliveira ◽  
G.H. Justi ◽  
G.C. Lopes
Keyword(s):  
Pressure Drop ◽  
Collection Efficiency ◽  
Fluid Dynamic ◽  
Two Phase ◽  
Mesh Structure ◽  
Pressure Drops ◽  
Regular Elements ◽  
Grid Convergence ◽  
Grid Convergence Index ◽  
Mesh Structures

In a cyclone design, pressure drop and collection efficiency are two important performance parameters to estimate its implementation viability. The optimum design provides higher efficiencies and lower pressure drops. In this paper, a grid independence study was performed to determine the most appropriate mesh to simulate the two-phase flow in a Stairmand cyclone. Computational fluid dynamic (CFD) tools were used to simulate the flow in an Eulerian-Lagrangian approach. Two different mesh structure, one with wall-refinement and the other with regular elements, and several mesh sizes were tested. The grid convergence index (GCI) method was applied to evaluate the result independence. The CFD model results were compared with empirical correlations from bibliography, showing good agreement. The wall-refined mesh with 287 thousand elements obtained errors of 9.8% for collection efficiency and 14.2% for pressure drop, while the same mesh, with regular elements, obtained errors of 8.7% for collection efficiency and 0.01% for pressure drop.

scholarly journals Pemodelan Penurunan Tekanan Brine di Dalam Pipa Injeksi pada Lapangan Panas Bumi Dieng

Jurnal MIPA ◽  
2017 ◽  
Vol 6 (2) ◽  
pp. 32
Author(s):  
Jeferson Polii
Keyword(s):  
Pressure Drop ◽  
Flow Line ◽  
Chemical Constituents ◽  
Temperature Drop ◽  
Fluid Pressure ◽  
Saturation Temperature ◽  
Geothermal Field ◽  
Chemical Pollution ◽  
Pressure Drops ◽  
Very High

Injeksi brine hasil dari fluida produksi panas bumi digunakan untuk mengisi volume pori batuan reservoir, mencegah penurunan tekanan batuan yang terlalu cepat, dan mencegah polusi panas dan polusi kimia pada lingkungan yang disebabkan oleh kandungan kimia tertentu pada brine. Pada pipa aliran brine terjadi penurunan tekanan fluida sepanjang aliran. Di lapangan panas bumi Dieng, konsentrasi silika sangat tinggi, sehingga penurunan temperatur saturasi memicu desposisi silika. Penurunan tekanan sepanjang pipa aliran brine dari pompa Vertikal Atas (VA) 7 ke pond di pad 29 di lapangan panas bumi Dieng akan menyebabkan penurunan temperatur saturasi, selain juga kehilangan panas secara alami. Perhitungan penurunan tekanan fluida brine berdasarkan perhitungan Harrison-Freeston dan metode dari Zhao, yang dikembangkan dengan algoritma menggunakan Macro Excel. Sehingga dengan memodelkan penurunan tekanan sepanjang pipa alir, dapat dikembangkan untuk perhitungan penurunan temperatur dan pengendapan silika di pipa aliran brine untuk injeksi panas bumi.Brine injection from geothermal production fluids is used to fill reservoir pore rock volumes, preventing rapid rock pressure drops, and preventing heat pollution and chemical pollution in the environment caused by certain chemical constituents in the brine. Decrease fluid pressure along the flow on the brine flow pipe. In the Dieng geothermal field, the silica concentration is very high, so the decrease in saturation temperature triggers the silica desposition. The pressure drop along the brine flow pipe from the Upper Vertical (VA) 7 pump to the pond in pad 29 in Dieng geothermal field will cause a decrease in saturation temperature, as well as natural heat loss. The calculation of the decrease in brine fluid pressure based on Harrison-Freeston calculations and methods of Zhao, developed with algorithms using Macro Excel. By modeling the pressure drop along the flow line, it can be developed for the calculation of temperature drop and deposition of silica in the brine flow pipe for geothermal injection

Experimental Investigation Into the High Altitude Relight of a Three-Cup Combustor Sector

2018 ◽  
Author(s):  
Michael J. Denton ◽  
Samir B. Tambe ◽  
San-Mou Jeng
Keyword(s):  
Pressure Drop ◽  
High Altitude ◽  
High Speed ◽  
Development Process ◽  
Recirculation Zone ◽  
Operating Conditions ◽  
Pressure Drops ◽  
High Speed Video ◽  
Air Jet ◽  
Flame Development

The altitude relight of a gas turbine combustor is an FAA and EASA regulation which dictates the successful re-ignition of an engine and its proper spool-up after an in-flight shutdown. Combustor pressure loss, ambient pressure, ambient temperature, and equivalence ratio were all studied on a full-scale, 3-cup, single-annular aviation combustor sector to create an ignition map. The flame development process was studied through the implementation of high-speed video. Testing was conducted by placing the sector horizontally upstream of an air jet ejector in a high altitude relight testing facility. Air was maintained at room temperature for varying pressure, and then the cryogenic heat exchanger was fed with liquid nitrogen to chill the air down to a limit of −50 deg F, corresponding with an altitude of 30,000 feet. Fuel was injected at constant equivalence ratios across multiple operating conditions, giving insight into the ignition map of the combustor sector. Results of testing indicated difficulty in achieving ignition at high altitudes for pressure drops greater than 2%, while low pressure drops show adequate performance. Introducing low temperatures to simulate the ambient conditions yielded a worse outcome, with all conditions having poor results except for 1%. High-speed video of the flame development process during the relight conditions across all altitudes yielded a substantial effect of the pressure drop on ignitability of the combustor. An increase in pressure drop was associated with a decrease in the likelihood of ignition success, especially at increasing altitudes. The introduction of the reduced temperature effect exacerbated this effect, further hurting ignition. High velocity regions in the combustor were detrimental to the ignition, and high area, low velocity regions aided greatly. The flame tended to settle into the corner recirculation zone and recirculate back into the center-toroidal recirculation zone (CTRZ), spreading downstream and likewise into adjacent swirl cups. These tests demonstrate the need for new combustor designs to consider adding large recirculation zones for combustor flame stability that will aid in relight requirements.

Advancements in Step Down Tests to Guide Perforation Cluster Design and Limited Entry Pressure Intensities - Learnings from Field Tests in Multiple Basins

2021 ◽  
Author(s):  
Somnath Mondal ◽  
Min Zhang ◽  
Paul Huckabee ◽  
Gustavo Ugueto ◽  
Raymond Jones ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Fracture Propagation ◽  
Field Tests ◽  
Pressure Drops ◽  
Wellbore Pressure ◽  
Hydraulic Fracture Propagation ◽  
Step Down ◽  
Cluster Design

Abstract This paper presents advancements in step-down-test (SDT) interpretation to better design perforation clusters. The methods provided here allow us to better estimate the pressure drop in perforations and near-wellbore tortuosity in hydraulic fracturing treatments. Data is presented from field tests from fracturing stages with different completion architectures across multiple basins including Permian Delaware, Vaca Muerta, Montney, and Utica. The sensitivity of near-wellbore pressure drops and perforation size on stimulation distribution effectiveness in plug-and-perf (PnP) treatments is modeled using a coupled hydraulic fracturing simulator. This advanced analysis of SDT data enables us to improve stimulation distribution effectiveness in multi-cluster or multiple entry completions. This analysis goes much further than the methodology presented in URTeC2019-1141 and additional examples are presented to illustrate its advantages. In a typical SDT, the injection flowrate is reduced in four or five abrupt decrements or "steps", each with a duration long enough for the rate and pressure to stabilize. The pressure-rate response is used to estimate the magnitude of perforation efficiency and near-wellbore tortuosity. In this paper, two SDTs with clean fluids were conducted in each stage - one before and another after proppant slurry was injected. SDTs were conducted in cemented single-point entry (cSPE) sleeves, which present a unique opportunity to measure only near-wellbore tortuosity using bottom-hole pressure gauge at sleeve depth, negligible perforation pressure drops, and less uncertainty in interpretation. SDTs were conducted in PnP stages in multiple unconventional basins. The results from one set of PnP stages with optic fiber distributed sensing were modeled with a hydraulic fracturing simulator that combines wellbore proppant transport, perforation size growth, near-wellbore pressure drop, and hydraulic fracture propagation. Past SDT analysis assumed that the pressure drop due to near-wellbore tortuosity is proportional to the flow rate raised to an exponent, β = 0.5, which typically overestimates perforation friction from SDTs. Theoretical derivations show that β is related to the geometry and flow type in the near-wellbore region. Results show that initial β (before proppant slurry) is typically around 0.5, but the final value of β (after proppant slurry) is approximately 1, likely due to the erosion of near-wellbore tortuosity by the proppant slurry. The new methodology incorporates the increase in β due proppant slurry erosion. Hydraulic fracturing modeling, calibrated with optic fiber data, demonstrates that the stimulation distribution effectiveness must consider the interdependence of proppant segregation in the wellbore, perforation erosion, and near-wellbore tortuosity. An improved methodology is presented to quantify the magnitude of perforation and near-wellbore tortuosity related pressure drops before and after pumping of proppant slurry in typical PnP hydraulic fracture stimulations. The workflow presented here shows how the uncertainties in the magnitude of near-wellbore complexity and perforation size, along with uncertainties in hydraulic fracture propagation parameters, can be incorporated in perforation cluster design.

Sign in / Sign up

Export Citation Format

Share Document