scholarly journals Hygrothermal Studies on GFRP Composites: A Review

2018 ◽  
Vol 144 ◽  
pp. 02026 ◽  
Author(s):  
Manjunath Shettar ◽  
Aakarshit Chaudhary ◽  
Zaid Hussain ◽  
U. Achutha Kini ◽  
Sathyashankara Sharma
Keyword(s):  
Fiber Reinforced Polymer ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced Polymer ◽  
Environment Effects ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Hygrothermal Environment ◽  
Fiber Matrix Interface ◽  
Fiber Matrix ◽  
The Individual

The objective of this paper is to review the hygrothermal environment effects on Glass Fiber Reinforced Polymer (GFRP) composites. A brief summary of the hygrothermal phenomenon and its mechanisms of GFRP is followed by detailed review of hygrothermal effects on the GFRP. The review also includes the different hygrothermal aging tests viz., cold soaking, boiling soaking, thermal shocks and use of environmental chamber, procedures and significance. At the end, hygrothermal effects on the individual constituents of GFRP viz., fiber, matrix and the fiber-matrix interface, are discussed.

EFFECT OF NANOCLAY CONTENT ON FLEXURAL PROPERTIES OF GLASS FIBER REINFORCED POLYMER (GFRP) COMPOSITES

2015 ◽  
Vol 76 (3) ◽  
Author(s):  
Widia Wahyuni Amir ◽  
Aidah Jumahat ◽  
Jamaluddin Mahmud
Keyword(s):  
Flexural Strength ◽  
Flexural Modulus ◽  
Fiber Reinforced Polymer ◽  
Flexural Test ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Gfrp Composite ◽  
Nanoclay Content

This paper presents a study on the flexural properties of glass fiber reinforced polymer composites. The epoxy-nanoclay resin was milled using a three roll mill machine to produce exfoliated structure nanocomposites. The fiber laminates specimens were manufactured by vacuum bagging system. These specimens were tested in the three point bend configuration following the ASTM D7264. The flexural modulus, flexural strength and strain to failure were then determined based on the flexural test results. The results showed that flexural modulus and flexural strength increases when a certain amount of nanoclay was included in the resin system. A maximum of 80% and 37% improvement of flexural strength and flexural modulus, respectively, were found at 5 wt% nanoclay content when compared to the neat GFRP composite. The improved properties of GFRP composites were achieved mostly due to an increase on the interfacial surface areas as well as a well-dispersion of nanoclay in the GFRP composite system. The fracture surfaces of specimens after flexural test were observed under FESEM. The results showed that the compressive failure region in the fiber was a dominant failure mechanism of the specimens due to a large compressive area on the fracture surface.

scholarly journals Effect of Sea Water Environment Exposure on Glass Fiber Reinforced Polymer Composites

2019 ◽  
Vol 9 (1) ◽  
pp. 670-674
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Mechanical Behaviour ◽  
Sea Water ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

Glass fiber reinforced polymer(GFRP) composites are currently used in large numbers of diverse applications ranging from tip and engine strut fairings in aircrafts, building panels and dash boards in automotive vehicles, boat hulls in ocean vehicle structures, golf clubs and race helmets in sports equipment, etc. The service life of composite materials are influenced by the different adverse environment which leads to various failures like corrosion, fatigue, fracture, etc., results in loss of structural integrity due to environmental conditions. The investigations involved are to study the mechanical behaviour of these materials when subjected to various adverse conditions of the environment at different intervals of exposure due to change in moisture and temperature. Experiments were conducted on GFRP composites with and without exposing to different environment conditions of sea water. Tensile and flexural tests are conducted to predict the mechanical behaviour of both normal specimens and specimens exposed with sea water. Reduction in mechanical properties found due to maximum absorption of any liquid by the material. When temperature increases better in mechanical properties are noticed and at low temperature the composite behaves like a brittle.

Preparation and Characterization of TiO2 Particulate Filled Polyester Based Glass Fiber Reinforced Polymer Composite

2014 ◽  
Vol 984-985 ◽  
pp. 360-366 ◽  
Author(s):  
S. Srinivasa Moorthy ◽  
K. Manonmani ◽  
M. Sankar Kumar
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Chemical Resistance ◽  
Fiber Content ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

Polyester based glass fiber reinforced polymer (GFRP) composites are widely used in marine and automotive industries because of its strength to weight ratio with lower price. In order to have the better properties of GFRP composites, the particulate filler material titanium oxide (TiO2) was added in unsaturated polyester resin with the fiber reinforcement by hand lay-up process. The fiber content was kept at 35 wt% constant with the fiber length of 5 cm. The particulate was varied with 2 wt. %, 4 wt. %, 6 wt. %, 8 wt. %, and 10 wt. %. Experiments were carried out to study the mechanical properties like tensile strength, impact strength, and Rockwell hardness. The chemical resistance analysis (CRA) was carried out by weight loss method. The mechanical properties of the hybrid reinforced composites were improved due to the fiber content with increased particulate content. The influence of the particulate content was more pronounced in the chemical resistance.

scholarly journals Combined Effects of Sustained Loads and Wet-Dry Cycles on Durability of Glass Fiber Reinforced Polymer Composites

2017 ◽  
Vol 2017 ◽  
pp. 1-14
Author(s):  
Mengting Li ◽  
Jun Wang ◽  
Weiqing Liu ◽  
Ruifeng Liang ◽  
Hota GangaRao ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
Fiber Reinforced Polymer ◽  
Distilled Water ◽  
Combined Effects ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Sustained Loads

This paper deals with durability of glass fiber reinforced polymer (GFRP) composites under the combined effects of sustained tensile loads and wet-dry (WD) cycles. Two different solutions (distilled water and saltwater) were used to imitate the freshwater and marine environments, respectively. Tensile properties of the unconditioned and conditioned specimens were measured to study the durability of GFRP composites under these 2 effects. The response indicated that both tensile strength and elastic modulus increased initially upon WD cycles, which was attributed to both the postcuring of resin and the sustained tensile stress allowing for fastec cure. Further exposure to WD cycles in distilled water or saltwater led to a steady decrease in tensile strength and modulus. WD cycles of saltwater and distilled water have similar effects on the degradation of the tensile properties for unstressed specimens. However, the elastic modulus and elongation at rupture of stressed specimens under WD cycles of saltwater decreased more than those specimens under WD cycles of distilled water. Moreover, increase of sustained loads led to a decrease in tensile strength. Based on Arrhenius method, a prediction model which accounted for the effects of postcure processes was developed. The predicted results of tensile strength and elastic modulus agree well with those obtained from the experiments.

scholarly journals Investigation bending behaviors of the slabs with glass fiber reinforced polymer composite and steel bars

2021 ◽  
Vol 4 (4) ◽  
pp. 227-238
Author(s):  
Alper Karadis ◽  
Kabil Cetin ◽  
Taha Yasin Altıok ◽  
Ali Demir
Keyword(s):  
Glass Fiber ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Polymer ◽  
Polypropylene Fibers ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Gfrp Composite ◽  
Steel Bars

Glass fiber reinforced polymer (GFRP) composites have been frequently used in engineering applications in recent years. GFRP composites produced by using glass fiber and epoxy resin have significant advantages such as high strength, lightness, and resistance against corrosion. However, GFRP composites exhibit a more brittle behavior than steel bars. This study aims to investigate both the experimental and numerical bending behavior of slabs with GFRP bars, steel bars, and polypropylene fiber. Within the scope of experimental studies, 5 slabs were built. Two slabs called SS-1 and SS-2 have only steel bars. Two slabs called GFRPS-1 and GFRPS-2 have only GFRP composite bars. A slab called GFRPS-F has both GFRP composite bars and polypropylene fibers. Polypropylene fibers are added to fresh concrete to improve the slab’s ductility. Three-point bending tests have been carried out on the slabs. All slabs are subjected to monotonic increasing distributed loading until collapse. As a result of tests, GFRPS slabs have carried %53 higher load than SS slabs. However, the SS slabs have exhibited a more ductile behavior compared to the GFRPS slabs. GFRPS slabs have more and larger crack width than other slabs. The addition of 5% polypropylene fiber by volume to concrete has a significant contributed to ductility and tensile behavior of slab. The average displacement value of GFRPS-F slab is 22.3% larger than GFRPS slab. GFRPS-F slab has better energy consumption capacity than other slabs. The energy consumption capacity of GFRPS-F slab is 1.34 and 1.38 times that of SS and GFRPS slabs, respectively. The number of cracks in GFRPS-F slab is fewer than GFRPS slabs. The fibers have contributed to the serviceability of the GFRPS slabs by limiting the displacement and the crack width. GFRPS-F exhibits elastoplastic behavior and almost returns to its first position when the loading is stopped. In addition, experimental results are verified with numerical results obtained by using Abaqus software. Finally, it is concluded that GFRP composite bars can be safely used in field concretes, concrete roads, prefabricated panel walls, and slabs.

scholarly journals Application of the Combined ANN and GA for Multi-Response Optimization of Cutting Parameters for the Turning of Glass Fiber-Reinforced Polymer Composites

Mathematics ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 947
Author(s):  
Azhar Equbal ◽  
Mohammad Shamim ◽  
Irfan Anjum Badruddin ◽  
Md. Israr Equbal ◽  
Anoop Kumar Sood ◽  
...  
Keyword(s):  
Glass Fiber ◽  
Cutting Parameters ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Response Optimization ◽  
Optimization Of Cutting Parameters

Glass fiber-reinforced polymer (GFRP) composites find wide applications in automobile, aerospace, aircraft and marine industries due to their attractive properties such as lightness of weight, high strength-to-weight ratio, high stiffness, good dimensional stability and corrosion resistance. Although these materials are required in a wide range of applications, their non-homogeneous and anisotropic properties make their machining troublesome and consequently restrict their use. It is thus important to study not only the machinability of these materials but also to determine optimum cutting parameters to achieve optimum machining performance. The present work focuses on turning of the GFRP composites with an aim to determine the optimal cutting parameters that yield the optimum output responses. The effect of three cutting parameters, i.e., spindle rotational speed (N), feed rate (f) and depth of cut (d) in conjunction with their interactions on three output responses, viz., Material Removal Rate (MRR), Tool Wear Rate (TWR), and Surface roughness (Ra), is studied using full factorial design of experiments (FFDE). The statistical significance of the cutting parameters and their interactions is determined using analysis of variance (ANOVA). To relate the output response and cutting parameters, empirical models are also developed. Artificial Neural Network (ANN) combined with Genetic Algorithm (GA) is employed for multi-response optimization to simultaneously optimize the MRR, TWR and Ra.

scholarly journals Experimental Investigation on the Durability of Glass Fiber-Reinforced Polymer Composites Containing Nanocomposite

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Weiwen Li ◽  
Chunyang Ji ◽  
Honggang Zhu ◽  
Feng Xing ◽  
Jiaxin Wu ◽  
...  
Keyword(s):  
Glass Fiber ◽  
Tensile Properties ◽  
Matrix Material ◽  
Fiber Reinforced Polymer ◽  
Clay Nanocomposites ◽  
Fiber Reinforced ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

Nanoclay layers incorporated into polymer/clay nanocomposites can inhibit the harmful penetration of water and chemicals into the material, and thus the durability of glass fiber-reinforced polymer (GFRP) composites should be enhanced by using polymer/clay nanocomposite as the matrix material. In this study, 1.5 wt% vinyl ester (VE)/organoclay and 2 wt% epoxy (EP)/organoclay nanocomposites were prepared by an in situ polymerization method. The dispersion states of clay in the nanocomposites were studied by performing XRD analysis. GFRP composites were then fabricated with the prepared 1.5 wt% VE/clay and 2.0 wt% EP/clay nanocomposites to investigate the effects of a nanocomposite matrix on the durability of GFRP composites. The durability of the two kinds of GFRP composites was characterized by monitoring tensile properties following degradation of GFRP specimens aged in water and alkaline solution at 60°C, and SEM was employed to study fracture behaviors of aged GFRP composites under tension. The results show that tensile properties of the two types of GFRP composites with and without clay degrade significantly with aging time. However, the GFRP composites with nanoclay show a lower degradation rate compared with those without nanoclay, supporting the aforementioned hypothesis. And the modification of EP/GFRP enhanced the durability more effectively.

Sign in / Sign up

Export Citation Format

Share Document