scholarly journals Modelling of the shear resistance of self-stressed beams reinforced with FRP applying the Critical Shear Crack Theory

2021 ◽  
Vol 350 ◽  
pp. 00016
Author(s):  
Viktar Tur ◽  
Aliaksandr Varabei
Keyword(s):  
Shear Crack ◽  
Crack Opening ◽  
Shear Resistance ◽  
Experimental Investigations ◽  
Inclined Crack ◽  
Ultimate State ◽  
Bond Slip ◽  
Crack Theory ◽  
Dowel Action ◽  
Frp Bars

This paper presents a mechanical model of the shear resistance based on Critical Shear Crack Theory (CSCT) and its application for the checking of the shear ultimate state of self-stressed elements reinforced with FRP bars. The shear force, which is transmitted through the inclined crack by aggregate interlock, residual tensile strength, dowel action and inclined chord of the compression concrete, is calculated depending on the value of the inclined crack opening, determined according to the modified law “bond-slip” for FRP bars. The reliability of the proposed approach is confirmed by comparison both with the results of our own experimental investigations and with numerous research results by various authors.

scholarly journals Comparison Crack Resistance of RC Beams with and without Transverse Reinforcement after Shear Testing

2019 ◽  
Vol 1 (1) ◽  
pp. 342-349
Author(s):  
Pavlo Vegera ◽  
Roman Khmil ◽  
Rostyslav Vashkevych ◽  
Zinoviy Blickharskyy
Keyword(s):  
Shear Strength ◽  
Crack Resistance ◽  
Shear Crack ◽  
Crack Opening ◽  
Shear Capacity ◽  
Rc Beams ◽  
Inclined Crack ◽  
Distribution Width ◽  
Shear Span ◽  
External Reinforcement

Abstract Main parameters, which characterize shear strength, are crack distribution, width of diagonal crack opening and angle of inclined crack. There are in this article, comparison crack resistant of testing reinforced concrete (RC) beams on the shear with such variable parameters like presence or absence internal reinforcement, different shear span, and presence or absence external composite reinforcement. Shear span (relative span to effective depth ratio) was acquired the following values: a/d=2, 1.5, 1. For internal reinforcement, rebar’s A240C with diameter 8 mm and steps 100 mm was chosen. The composite FRCM system was like external reinforcement with three stripe of composite fabric with width 70 mm and step 100 mm. Eight RC beams were tested. After testing, we discovered that the most influenced on the serviceability capacity was shear span. Internal transverse reinforcing increased shear strength on the same level and it was independent from shear span and other factors. Only quantity of reinforcing determine level of increasing shear capacity. FRCM system is efficient strengthening system, which significant increase shear crack resistant for RC beams. External FRCM reinforcing increase shear crack resistance on the same percentage and independent from presence or absence internal reinforcement.

Cracking and Failure Mode of the Self-Stressed Members with FRP Bars

2019 ◽  
Vol 292 ◽  
pp. 230-235 ◽  
Author(s):  
Volha Semianiuk ◽  
Viktar V. Tur
Keyword(s):  
Failure Mode ◽  
Elasticity Modulus ◽  
Crack Opening ◽  
Polymer Binder ◽  
The Self ◽  
Experimental Investigations ◽  
Bond Performance ◽  
Reinforcing Fibers ◽  
Frp Reinforcement ◽  
Frp Bars

Fiber reinforced polymer (FRP) bars represent a combination of the polymer binder and reinforcing fibers (glass, basalt, aramid, carbon). The main features of FRP bars are high tensile strength on the background of the relatively low elasticity modulus. To prevent development of the excessive both crack opening and deflections in the FRP reinforced concrete structures it can be effective to implement FRP reinforcement pretensioning with a limited level of created stresses. As a good option can be considered a physico-chemical method of FRP bars pretensioning based on the self-stressing concrete utilizing. In the self-stressed FRP reinforced members it is possible to obtain a considerable values of the early age restrained expansion strains (in comparison with steel reinforced self-stressed members because of FRP bars lower elasticity modulus), which will not disappear after air-dry shrinkage strains realization. In addition, another concern that have to be considered in the field of FRP reinforced self-stressed members is bond performance of the different FRP bars types, especially in combination with self-stressing concrete that within its expansion can provoke decompacting of the transit zone «bar-concrete». Moreover, taking into account that FRP bars is a composite material, its bond properties are strongly influenced by the types of the polymer binder, reinforcing fibers, ratio between binder and fibers, bar coating. Presented studies is consisted in the experimental investigations of the features in the crack development and depended on it occurred failure mode of the self-stressed members reinforced by the different types of FRP bars.

Critical shear crack theory-based punching shear model for FRP-reinforced concrete slabs

2020 ◽  
pp. 136943322097814
Author(s):  
Xing-lang Fan ◽  
Sheng-jie Gu ◽  
Xi Wu ◽  
Jia-fei Jiang
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Shear Crack ◽  
Concrete Strength ◽  
Weight Ratio ◽  
Punching Shear ◽  
Concrete Slabs ◽  
Crack Theory ◽  
Reinforced Concrete Slabs ◽  
Rc Slabs

Owing to their high strength-to-weight ratio, superior corrosion resistance, and convenience in manufacture, fiber-reinforced polymer (FRP) bars can be used as a good alternative to steel bars to solve the durability issue in reinforced concrete (RC) structures, especially for seawater sea-sand concrete. In this paper, a theoretical model for predicting the punching shear strength of FRP-RC slabs is developed. In this model, the punching shear strength is determined by the intersection of capacity and demanding curve of FRP-RC slabs. The capacity curve is employed based on critical shear crack theory, while the demand curve is derived with the help of a simplified tri-linear moment-curvature relationship. After the validity of the proposed model is verified with experimental data collected from the literature, the effects of concrete strength, loading area, FRP reinforcement ratio, and effective depth of concrete slabs are evaluated quantitatively.

Crack Resistance of the Self-Stressed Members Reinforced with FRP Bars

2018 ◽  
Vol 272 ◽  
pp. 244-249 ◽  
Author(s):  
Volha Semianiuk ◽  
Viktar V. Tur
Keyword(s):  
Initial Stress ◽  
Static Loading ◽  
Strain State ◽  
Crack Opening ◽  
The Self ◽  
Stress Strain ◽  
Diagram Method ◽  
Stress Strain State ◽  
Expansion Stage ◽  
Frp Bars

Fiber reinforced polymer (FRP) bars are widely used in building structures, especially that are exposed to the aggressive environment influence and other special conditions. Nevertheless, due to the low FRP (e.g. glass, basalt, aramid fibers reinforced polymers) bars modulus of elasticity, exceeding crack opening width, as well as deflections can be observed. FRP bars pretensioning is considered as an effective method of its structural performance increasing. Physico-chemical method of the FRP bars pretensioning based on the self-stressing concrete utilizing is an alternative to the mechanical method and in its turn doesn’t need for special devices and anchorage systems as well as qualified personnel. Assessment of the initial stress-strain state obtained during self-stressing concrete expansion stage in the reinforced self-stressed members is presented. Diagram method of the self-stressing parameters verification based on the static loading tests results is presented. Comparison of the initial stress-strain state obtained during concrete expansion stage and predicted by the proposed model, as well as assessment of its influence on the behavior at the static loading stage in cases of the self-stressed reinforced with FRP bars members and traditionally reinforced with steel bars self-stressed members was performed.

scholarly journals Bearing capacity calculation of reinforced concrete corbels under the shear action

2018 ◽  
Vol 230 ◽  
pp. 02005 ◽  
Author(s):  
Oksana Dovzhenko ◽  
Volodymyr Pohribnyi ◽  
Volodymyr Pents ◽  
Dmytro Mariukha
Keyword(s):  
Plastic Deformation ◽  
Reinforced Concrete ◽  
Plasticity Theory ◽  
Inclined Crack ◽  
Ultimate State ◽  
Rigid Plastic ◽  
Characteristic Lines ◽  
Capacity Calculation ◽  
Theory Use ◽  
Concrete Elements

The necessity of creating a general methodology for concrete and reinforced concrete elements strength calculation under the shear is established. Three failure cases of reinforced concrete corbels under the shear are considered. The solutions of problems of corbels strength with failure along the whole section, close to the normal, in the compressed zone under an inclined crack and within the compressed inclined strip are given. A variational method in the plasticity theory, the virtual velocities principle and the characteristic lines method are used for concrete and reinforced concrete elements calculations. In the ultimate state, concrete is considered as a rigid-plastic body. The shear is realized in case when the plastic deformation is localized in the compressed zone. The calculating ultimate load results for different failure cases are given. Such a design scheme is implemented, in which the console strength is minimal. This corresponds to the minimum of power of plastic deformation in concrete compressed zone. Reinforced concrete corbels calculation engineering methods are offered. The elements obtaining effective constructive decisions direction based on the plasticity theory use is determined.

scholarly journals Bond-Slip Models for FPR-Concrete Interfaces Subjected to Moisture Conditions

2017 ◽  
Vol 2017 ◽  
pp. 1-14 ◽  
Author(s):  
Justin Shrestha ◽  
Dawei Zhang ◽  
Tamon Ueda
Keyword(s):  
Fiber Reinforced Polymers ◽  
Experimental Investigations ◽  
Reinforced Polymers ◽  
Bond Slip ◽  
Exposure Effect ◽  
Pull Out ◽  
Proposed Model ◽  
Maximum Period ◽  
Moisture Conditions

Environmental related durability issues have been of great concerns in the structures strengthened with the fiber reinforced polymers (FRPs). In marine environment, moisture is one of the dominant factors that adversely affect the material properties and the bond interfaces. Several short-term and long-term laboratory experimental investigations have been conducted to study such behaviors but, still, there are insufficient constitutive bond models which could incorporate moisture exposure conditions. This paper proposed a very simple approach in determining the nonlinear bond-slip models for the FRP-concrete interface considering the effect of moisture conditions. The proposed models are based on the strain results of the experimental investigation conducted by the authors using 6 different commercial FRP systems exposed to the moisture conditions for the maximum period of 18 months. The exposure effect in the moisture conditions seems to have great dependency on the FRP system. Based on the contrasting differences in the results under moisture conditions, separate bond-slip models have been proposed for the wet-layup FRP and prefabricated FRP systems. As for the verification of the proposed model under moisture conditions, predicted pull-out load was compared with the experimental pull-out load. The results showed good agreement for all the FRP systems under investigation.

Investigation of bond between fibre-reinforced polymer bars and concrete under sustained loads

2006 ◽  
Vol 33 (11) ◽  
pp. 1426-1437 ◽  
Author(s):  
F Shahidi ◽  
L D Wegner ◽  
B F Sparling
Keyword(s):  
Reinforced Concrete ◽  
Sustained Load ◽  
Reinforcing Bars ◽  
Bond Slip ◽  
Reinforced Polymer ◽  
Sustained Loads ◽  
Fibre Reinforced Polymer ◽  
Term Performance ◽  
Frp Bars

Although the use of fibre-reinforced polymer (FRP) bars to replace steel in reinforced concrete is becoming more common, uncertainty remains concerning the long-term performance of FRP, including the effect of a sustained load on the bond between the FRP bars and the concrete. An experimental study was therefore undertaken to investigate the long-term durability of the bond for various types of bars embedded in concrete: one type of glass FRP, two types of carbon FRP, and conventional steel reinforcing bars. Pullout specimens were tested both statically to failure and under sustained loads for periods of up to 1 year while free-end slip was monitored. Results revealed lower short-term bond strengths for FRP bars relative to steel and significant variability in long-term bond-slip performance among FRP bars of different types. Post-testing investigations revealed damage to bar surfaces at the macroscopic level, as well as broken longitudinal fibres and damage to the surface coatings at the microscopic level.Key words: reinforced concrete, fibre-reinforced polymer (FRP), bond, creep, pullout, sustained loads.

scholarly journals Influence of the initial prestressing on the crack resistance of the self-stressed members reinforced with steel and FRP bars

2019 ◽  
Vol 262 ◽  
pp. 08004
Author(s):  
Volha Semianiuk ◽  
Viktar Tur ◽  
Siarhei Semianiuk
Keyword(s):  
Crack Opening ◽  
Density Ratio ◽  
High Strength ◽  
Negative Influence ◽  
The Self ◽  
Engineering Practice ◽  
Mechanical Resistance ◽  
Concrete Members ◽  
Early Age Concrete ◽  
Frp Bars

Fiber reinforced polymer(FRP) bars are widely utilized in the civil engineering practice and characterized by the number of advantages, among them are the following: high strength-to-density ratio; absence of corrosion; resistance to the negative influence of the different aggressive mediums. Nevertheless, a wide practical application of such a bars finds an embarrassment because of the law modulus of elasticity (in the diapason from 30 GPa to 60 GPa), that in its turn lead to the development of the excessive crack opening as well as deflections under the loading. To enhance structural performance of the FRP reinforced concrete members, pretensioning of FRP bars can be considered as a good option. Opposite to the concrete members mechanical pretensioning, physico-chemical method of bars pretensioning based on the self-stressing concrete utilizing is considered. Influence of the controlled initial stress-strain state obtained during early age concrete expansion on the mechanical resistance of the self-stressed concrete members reinforced with both steel and FRP bars was studied. Comparison of the prestressing effectiveness of the self-stressing concrete members with steel and FRP bars was performed. Proposition for effective utilizing of the FRP bars in the self-stressed concrete members was formulated based on results of the presented investigation.

Sign in / Sign up

Export Citation Format

Share Document