scholarly journals A large gain variable range, high linearity, lownoise, low DC offset VGAs used in BD system

2022 ◽  
Vol 355 ◽  
pp. 03050
Author(s):  
Dianwei Zhang ◽  
Fei Chu ◽  
Wu Wen ◽  
Ze Cheng
Keyword(s):  
Supply Voltage ◽  
Automatic Gain Control ◽  
Gain Control ◽  
Low Noise ◽  
Offset Cancellation ◽  
Dc Offset ◽  
Variable Range ◽  
High Linearity ◽  
Noise Characteristics ◽  
Large Gain

In this paper, a large gain variable range, high linearity, low noise, low DC offset VGAs with a simple gain-dB variable circuit are introduced. In the VGAs chain, the last and the first VGAs employ Bipolar transistors, to improve the linearity and noise characteristics. And the middle three stages VGAs employ MOS transistors. The whole circuitry is designed in 0.35um BiCMOS process, including variable gain amplifiers (VGAs) , fixed gain amplifiers , gain control and DC offset cancellation parts. The automatic gain control loop (AGC) provides a process independent gain variable range of 60dB (including 50dB gain-dB-linearity variable range), with a 200us loop lock time, the VGAs provide a 73dB largest gain, the THD is less than 1% at a 1V(P-P) output level; the equivalent output integral noise is 0.011v/√hz@20MHz bandwidth. The whole area is 1173um*494 um, and the power is 7.1mA at 3.3V signal supply voltage.

CMOS automatic gain control circuit with DC offset cancellation for FM/cw ladar

2014 ◽  
Vol 20 (4) ◽  
pp. 310-314
Author(s):  
Yiqiang Zhao ◽  
Min Xu ◽  
Ruilong Pang ◽  
Haixia Yu ◽  
Hongliang Zhao
Keyword(s):  
Automatic Gain Control ◽  
Gain Control ◽  
Control Circuit ◽  
Offset Cancellation ◽  
Dc Offset

A novel analog/digital reconfigurable automatic gain control with a novel DC offset cancellation circuit

2011 ◽  
Vol 32 (2) ◽  
pp. 025002
Author(s):  
Xiaofeng He ◽  
Taishan Mo ◽  
Chengyan Ma ◽  
Tianchun Ye
Keyword(s):  
Automatic Gain Control ◽  
Gain Control ◽  
Offset Cancellation ◽  
Dc Offset

scholarly journals A Four-Channel Low-Noise Readout IC for Air Flow Measurement Using Hot Wire Anemometer in 0.18 μm CMOS Technology

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4694
Author(s):  
Kyeongsik Nam ◽  
Hyungseup Kim ◽  
Yongsu Kwon ◽  
Gyuri Choi ◽  
Taeyup Kim ◽  
...  
Keyword(s):  
Supply Voltage ◽  
Air Flow ◽  
Low Noise ◽  
Cmos Process ◽  
Significant Information ◽  
Flow Measurements ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Op Amp ◽  
Noise Characteristics

Air flow measurements provide significant information required for understanding the characteristics of insect movement. This study proposes a four-channel low-noise readout integrated circuit (IC) in order to measure air flow (air velocity), which can be beneficial to insect biomimetic robot systems that have been studied recently. Instrumentation amplifiers (IAs) with low-noise characteristics in readout ICs are essential because the air flow of an insect’s movement, which is electrically converted using a microelectromechanical systems (MEMS) sensor, generally produces a small signal. The fundamental architecture employed in the readout IC is a three op amp IA, and it accomplishes low-noise characteristics by chopping. Moreover, the readout IC has a four-channel input structure and implements an automatic offset calibration loop (AOCL) for input offset correction. The AOCL based on the binary search logic adjusts the output offset by controlling the input voltage bias generated by the R-2R digital-to-analog converter (DAC). The electrically converted air flow signal is amplified using a three op amp IA, which is passed through a low-pass filter (LPF) for ripple rejection that is generated by chopping, and converted to a digital code by a 12-bit successive approximation register (SAR) analog-to-digital converter (ADC). Furthermore, the readout IC contains a low-dropout (LDO) regulator that enables the supply voltage to drive digital circuits, and a serial peripheral interface (SPI) for digital communication. The readout IC is designed with a 0.18 μm CMOS process and the current consumption is 1.886 mA at 3.3 V supply voltage. The IC has an active area of 6.78 mm2 and input-referred noise (IRN) characteristics of 95.4 nV/√Hz at 1 Hz.

A Low-Noise, Low-Power, Wide Dynamic Range Logarithmic Amplifier for Biomedical Applications

2018 ◽  
Vol 27 (07) ◽  
pp. 1850104 ◽  
Author(s):  
Yuwadee Sundarasaradula ◽  
Apinunt Thanachayanont
Keyword(s):  
Low Power ◽  
Biomedical Applications ◽  
Dynamic Range ◽  
Supply Voltage ◽  
Low Noise ◽  
Power Supply Voltage ◽  
Wide Dynamic Range ◽  
Dc Offset ◽  
Limiting Amplifier ◽  
Logarithmic Amplifier

This paper presents the design and realization of a low-noise, low-power, wide dynamic range CMOS logarithmic amplifier for biomedical applications. The proposed amplifier is based on the true piecewise linear function by using progressive-compression parallel-summation architecture. A DC offset cancellation feedback loop is used to prevent output saturation and deteriorated input sensitivity from inherent DC offset voltages. The proposed logarithmic amplifier was designed and fabricated in a standard 0.18[Formula: see text][Formula: see text]m CMOS technology. The prototype chip includes six limiting amplifier stages and an on-chip bias generator, occupying a die area of 0.027[Formula: see text]mm2. The overall circuit consumes 9.75[Formula: see text][Formula: see text]W from a single 1.5[Formula: see text]V power supply voltage. Measured results showed that the prototype logarithmic amplifier exhibited an 80[Formula: see text]dB input dynamic range (from 10[Formula: see text][Formula: see text]V to 100[Formula: see text]mV), a bandwidth of 4[Formula: see text]Hz–10[Formula: see text]kHz, and a total input-referred noise of 5.52[Formula: see text][Formula: see text]V.

A CMOS Automatic Gain Control Circuit for Biomedical Applications

2015 ◽  
Vol 645-646 ◽  
pp. 1308-1313
Author(s):  
Zhi Qiang Gao ◽  
Fu Xiang Huang ◽  
Jing Li ◽  
Liang Yin ◽  
Xiao Wei Liu
Keyword(s):  
Exponential Function ◽  
Biomedical Applications ◽  
Low Voltage ◽  
Supply Voltage ◽  
Automatic Gain Control ◽  
Gain Control ◽  
Cmos Technology ◽  
Chip Area ◽  
Gain Variation ◽  
Linearity Error

In this paper, a low-voltage automatic gain control (AGC) circuits is presented. The proposed circuit uses a novel approximated exponential function to increase the dB-linear output range. The three-stage AGC is fabricated in 0.18μm CMOS technology and shows the maximum gain variation of more than 100dB and a 67dB linear range with linearity error of less than ±1dB. The range of gain variation can be controlled from 34 to 101dB. The AGC dissipates less than 2.3mA under 1.8V supply voltage while occupying 0.4mm2 of chip area.

scholarly journals 14.85 µW Analog Front-End for Photoplethysmography Acquisition with 142-dBΩ Gain and 64.2-pArms Noise

Sensors ◽  
2019 ◽  
Vol 19 (3) ◽  
pp. 512
Author(s):  
Binghui Lin ◽  
Mohamed Atef ◽  
Guoxing Wang
Keyword(s):  
Dynamic Range ◽  
Automatic Gain Control ◽  
Gain Control ◽  
Low Noise ◽  
Total Power ◽  
Cmos Process ◽  
Control Block ◽  
Silicon Area ◽  
Front End ◽  
Analog Front End

A low-power, high-gain, and low-noise analog front-end (AFE) for wearable photoplethysmography (PPG) acquisition systems is designed and fabricated in a 0.35 μm CMOS process. A high transimpedance gain of 142 dBΩ and a low input-referred noise of only 64.2 pArms was achieved. A Sub-Hz filter was integrated using a pseudo resistor, resulting in a small silicon area. To mitigate the saturation problem caused by background light (BGL), a BGL cancellation loop and a new simple automatic gain control block are used to enhance the dynamic range and improve the linearity of the AFE. The measurement results show that a DC photocurrent component up-to-10 μA can be rejected and the PPG output swing can reach 1.42 Vpp at THD < 1%. The chip consumes a total power of 14.85 μW using a single 3.3-V power supply. In this work, the small area and efficiently integrated blocks were used to implement the PPG AFE and the silicon area is minimized to 0.8 mm × 0.8 mm.

Sign in / Sign up

Export Citation Format

Share Document