scholarly journals Comparison of Depth of Cure, Hardness and Heat Generation of LED and High Intensity QTH Light Sources

2011 ◽  
Vol 05 (03) ◽  
pp. 299-304 ◽  
Author(s):  
Sayed Mostafa Mousavinasab ◽  
Ian Meyers
Keyword(s):  
Light Source ◽  
Exposure Time ◽  
High Power ◽  
Second Generation ◽  
Light Sources ◽  
Curing Time ◽  
Led Light ◽  
Depth Of Cure ◽  
Thermal Changes ◽  
Qth Light

ABSTRACTObjectives: To compare curing performance of a second generation LED curing light with a high power tungsten quartz halogen (QTH). Methods: A hybrid composite resin (Filtek Z 250, 3M, USA) was used as test material and cured using a second generation LED light (Translux Power BlueTM, Heraus Kulzer ,Germany) or a very high power QTH light unit (EMS, Switzerland). A two split aluminum mold was used to prepare ten samples with LED light source cured for forty seconds and ten samples prepared using high power QTH light unit, cured for four or six seconds recommended exposure time. Hardness, depth of cure (DOC) and thermal rise during exposure time by these light sources were measured. The data submitted to analysis of variance (ANOVA), Tukey's and student's t tests at 5% significance level. Results: Significant differences were found in hardness, DOC of samples cured by above mentioned light sources and also in thermal rises during exposure time. The curing performance of the tested QTH was not as well as the LED light. TPB light source produced the maximum hardness (81.25, 73.29, 65.49,55.83 and 24.53 for 0 mm, 1 mm, 2 mm, 3 mm and 4 mm intervals) and DOC (2.64 mm) values with forty seconds irradiation time and the high power (QTH) the least hardness (73.27, 61.51 and 31.59 for 0 mm, 1 mm and 2 mm, respectively) and DOC (2 mm) values with four seconds irradiation time.Thermal rises during 4 s and 6 s curing time using high power QTH and tested LED were 1.88˚C, 3˚C and 1.87˚C, respectively. Conclusions: The used high power LED light produced greater hardness and depth of cure during forty seconds exposure time compared to high power QTH light with four or six seconds curing time. Thermal rise during 6 s curing time with QTH was greater compared to thermal changes occurred during 40 s curing time with tested LED light source. There was no difference seen in thermal changes caused by LED light with 40 s and QTH light with 4 s exposure time. (Eur J Dent 2011;5:299- 304)

scholarly journals Analysis on High-Power Seaport LED Luminaire with Uniform Light Distribution Based on Optimized Lens and Heatsink

2021 ◽  
Vol 11 (9) ◽  
pp. 4035
Author(s):  
Jinsheon Kim ◽  
Jeungmo Kang ◽  
Woojin Jang
Keyword(s):  
Light Source ◽  
High Power ◽  
Heat Dissipation ◽  
Light Emitting Diode ◽  
Light Distribution ◽  
Light Sources ◽  
Led Light ◽  
High Power Led ◽  
Distribution Requirement ◽  
Lighting Application

In the case of light-emitting diode (LED) seaport luminaires, they should be designed in consideration of glare, average illuminance, and overall uniformity. Although it is possible to implement light distribution through auxiliary devices such as reflectors, it means increasing the weight and size of the luminaire, which reduces the feasibility. Considering the special environment of seaport luminaires, which are installed at a height of 30 m or more, it is necessary to reduce the weight of the device, facilitate replacement, and secure a light source with a long life. In this paper, an optimized lens design was investigated to provide uniform light distribution to meet the requirement in the seaport lighting application. Four types of lens were designed and fabricated to verify the uniform light distribution requirement for the seaport lighting application. Using numerical analysis, we optimized the lens that provides the required minimum overall uniformity for the seaport lighting application. A theoretical analysis for the heatsink structure and shape were conducted to reduce the heat from the high-power LED light sources up to 250 W. As a result of these analyses on the heat dissipation characteristics of the high-power LED light source used in the LED seaport luminaire, the heatsink with hexagonal-shape fins shows the best heat dissipation effect. Finally, a prototype LED seaport luminaire with an optimized lens and heat sink was fabricated and tested in a real seaport environment. The light distribution characteristics of this prototype LED seaport luminaire were compared with a commercial high-pressure sodium luminaire and metal halide luminaire.

scholarly journals Polymerization quality testing of composite resins cured by led light source

2003 ◽  
Vol 50 (1) ◽  
pp. 7-12 ◽  
Author(s):  
Larisa Blazic ◽  
Slavoljub Zivkovic ◽  
Dejan Pantelic ◽  
Vladimir Pipic
Keyword(s):  
Light Source ◽  
Light Exposure ◽  
Light Emitting Diode ◽  
Composite Resins ◽  
Curing Time ◽  
Light Emitting ◽  
Led Light ◽  
Depth Of Cure ◽  
Dental Tissues ◽  
Hard Dental Tissues

The quality of interface between composite resin materials and hard dental tissues is highly dependent on the polymerization light source. Newly developed blue light- emitting diode units for light polymerization of dental restorative materials are the most innovative light source technology in dentistry nowadays. The aim of this work was to estimate the depth of cure of five different light-activating composite resins exposed to different irradiation times (5s, 10s, 20s and 40s) when the experimental LED light source was used. The tested materials were: Tetric Ceram (Vivadent), Point 4 (Kerr), Admira (VOCO), Filtek Z250 (3M) and Diamond Lite (DRM Lab., Inc). The depth of cure testing was determined using a penetrometer. Results after 40s curing time were as following: the deepest depth of cure was achieved after application of Filtek Z 250, Diamond Lite Point 4 and Tetric Ceram. For the restorative material Admira was found the lowest depth of cure for the light exposure of 40s. An experimental LED light source achieved a sufficient depth of cure (over 2 mm) for all tested materials after curing time of 10s. The polymerization light source spectral distribution should be considered in addition to irradiance as a depth of cure indicator.

scholarly journals Lifetime prediction of a multi-chip high-power LED light source based on artificial neural networks

2019 ◽  
Vol 12 ◽  
pp. 361-367 ◽  
Author(s):  
Hongwei Liu ◽  
Dandan Yu ◽  
Pingjuan Niu ◽  
Zanyun Zhang ◽  
Kai Guo ◽  
...  
Keyword(s):  
Neural Networks ◽  
Artificial Neural Networks ◽  
Light Source ◽  
High Power ◽  
Lifetime Prediction ◽  
Led Light ◽  
High Power Led ◽  
Artificial Neural

scholarly journals Photobiocatalytic alcohol oxidation using LED light sources

2017 ◽  
Vol 19 (2) ◽  
pp. 376-379 ◽  
Author(s):  
M. Rauch ◽  
S. Schmidt ◽  
I. W. C. E. Arends ◽  
K. Oppelt ◽  
S. Kara ◽  
...  
Keyword(s):  
Light Source ◽  
Photocatalytic Oxidation ◽  
Alcohol Oxidation ◽  
Light Sources ◽  
Blue Led ◽  
Led Light

The photocatalytic oxidation of NADH using a flavin photocatalyst and a simple blue LED light source is reported.

scholarly journals Effect of Light-Sources and Thicknesses of Composite Onlays on Micro-Hardness of Luting Composites

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6849
Author(s):  
Francesco De Angelis ◽  
Mirco Vadini ◽  
Mario Capogreco ◽  
Camillo D’Arcangelo ◽  
Maurizio D’Amario
Keyword(s):  
High Power ◽  
Resin Composite ◽  
Composite Layer ◽  
Resin Cement ◽  
Specimen Thickness ◽  
Light Sources ◽  
Curing Time ◽  
Resin Cements ◽  
Halogen Light ◽  
Light Curing

The aim of this study was to compare three different light-curing-units (LCUs) and determine their effectiveness in the adhesive cementation of indirect composite restorations when a light-curing resin cement is used. Two resin composites were selected: Enamel Plus HRI (Micerium) and AURA (SDI). Three thicknesses (3 mm, 4 mm and 5 mm) were produced and applied as overlays and underlays for each resin composite. A standardized composite layer was placed between underlay and overlay surfaces. Light curing of the resin-based luting composites was attained through the overlay filters using LCUs for different exposure times. All specimens were allocated to experimental groups according to the overlay thickness, curing unit and curing time. Vickers Hardness (VH) notches were carried out on each specimen. Data were statistically evaluated. The curing unit, curing time and overlay thickness were significant factors capable of influencing VH values. The results showed significantly decreased VH values with increasing specimen thickness (p < 0.05). Significant differences in VH values were found amongst the LCUs for the various exposure times (p < 0.05). According to the results, a time of cure shorter than 80 s (with a conventional quartz–tungsten–halogen LCU) or shorter than 40 s (with a high-power light-emitting diode (LED) LCU) is not recommended. The only subgroup achieving clinically acceptable VH values after a short 20 s curing time included the 3 mm-thick overlays made out of the AURA composite, when the high-power LED LCU unit was used (VH 51.0). Composite thickness has an intense effect on polymerization. In clinical practice, light-cured resin cements may result in insufficient polymerization for high thickness and inadequate times. High-intensity curing lights can attain the sufficient polymerization of resin cements through overlays in a significantly shorter time than conventional halogen light.

Effectiveness of Second-generation Light-emitting Diode (LED) Light Curing Units

2007 ◽  
Vol 8 (2) ◽  
pp. 35-42 ◽  
Author(s):  
Fabrício Aulo Ogliari ◽  
Ulisses Bastos Campregher ◽  
Susana Maria Werner Samuel ◽  
Carmen Beatriz Borges Fortes ◽  
Alberth David Correa Medina ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Second Generation ◽  
Light Emitting Diode ◽  
Strength Properties ◽  
Knoop Hardness ◽  
Curing Time ◽  
Light Emitting ◽  
Led Light ◽  
Three Samples ◽  
Light Curing

Abstract Aim The purpose of this study was to evaluate the effectiveness of three commercially available light emitting diode (LED) light curing units (LCU) (Elipar FreeLight - 3M ESPE; UltraLume LED2 - Ultradent; and Single V - BioArt) for polymerizing Z250-A3 composite (3M ESPE) using Knoop hardness, polymerization depth, and flexural strength properties. Methods and Materials The XL 2500 (3M ESPE) LCU, which is a conventional halogen unit, was used as a control. In all cases the curing time was 20 seconds. Hardness was determined 24 hours after composite cure for 10 samples of 8 mm diameter and 2 mm height for each LCU tested. Samples were stored dry in a lightproof container prior to testing. The depth of cure of the composite was measured immediately after composite polymerization for each LCU using three samples 4 mm in diameter and 6 mm in height. Flexural strength was determined for five samples 24 hours after immersion in distilled water at 37°C. Each sample measured 25 mm in length, 2 mm in width, and 2 mm in height for each LCU tested. Conclusion The results were treated statistically for comparison of the LCUs. In all cases the results obtained by LED LCUs were not different or were higher than a conventional halogen LCU. Clinical Significance Second generation LED LCUs were as effective as/or more effective than a halogen LCU for polymerization of the used composite. The present study shows second generation LEDs have the potential to replace halogen LCUs. Citation Campregher UB, Samuel SMW, Fortes CBB, Medina ADC, Collares FMC, Ogliari FA. Effectiveness of Second-generation Light-emitting Diode (LED) Light Curing Units. J Contemp Dent Pract 2007 February;(8)2:035-042.

RESEARCH OF LIGHTING CONDITIONS BY LED LIGHT SOURCES SECOND GENERATION

2019 ◽  
pp. 53-56
Author(s):  
O. E. Zheleznikova ◽  
S. Juma Mohammed ◽  
A. N. Mikhal’kova ◽  
S. A. Mikaeva
Keyword(s):  
Second Generation ◽  
Light Sources ◽  
Led Light ◽  
Lighting Conditions

scholarly journals Investigation on optical integration between LED Mid-IR light sources and Si-based waveguides for sensing applications

2021 ◽  
Vol 2145 (1) ◽  
pp. 012056
Author(s):  
Pawaphat Jaturaphagorn ◽  
Papichaya Chaisakul ◽  
Nattaporn Chattham ◽  
Pichet Limsuwan
Keyword(s):  
Integrated Circuits ◽  
Light Source ◽  
Light Emitting Diode ◽  
Coupling Scheme ◽  
Light Sources ◽  
Optical Coupling ◽  
Led Light ◽  
Carbon Dioxide Gas ◽  
Sensing Applications ◽  
Ir Light

Abstract Research on mid-IR silicon-based waveguides has recently received strong interest. Particularly, this paper focuses on one of the critical issues in micron-scale photonic integrated circuits, which is to efficiently couple a mid-IR LED (light emitting diode) light source to an external micron-scale waveguide. The optical coupling scheme is crucial for the exploitation of LED light sources in waveguide-based spectroscopic sensing applications. This paper reports optical coupling scheme between an LED mid-IR light source and a silicon rich silicon nitride (SiN) waveguide that could enable the use of LED-based light sources. Finally, the detection limit of the investigated device for carbon dioxide gas detection is calculated.

Predicting solutions toward improved high power white LED light sources: a combined theoretical and experimental study

2008 ◽  
Author(s):  
C. Sommer ◽  
F. P. Wenzl ◽  
L. Kuna ◽  
E. Zinterl ◽  
J. R. Krenn ◽  
...  
Keyword(s):  
Experimental Study ◽  
High Power ◽  
Light Sources ◽  
White Led ◽  
Led Light
Sign in / Sign up

Export Citation Format

Share Document