Local strain measurements in shallow trench insulator structures using near-ultraviolet Raman spectroscopy: Simulation and experiment

2007 ◽  
Vol 102 (10) ◽  
pp. 103506 ◽  
Author(s):  
Eddy Latu-Romain ◽  
Michel Mermoux ◽  
Alexandre Crisci ◽  
Dominique Delille ◽  
Laurens F. Tz. Kwakman
Author(s):  
Mauro G. Marinho ◽  
Alexandre M. Pope ◽  
Luiz Claudio Meniconi ◽  
Luiz Henrique M. Alves ◽  
Cesar Del Vecchio

Following the warning of a flooded bow horizontal brace of a semi-submersible production platform, an inspection diving team was mobilized and cracks were found at both bow and aft K-joints. Analysis of the service life of the platform, together with the results of structural analysis and local strain measurements, concluded that cracking was caused by fatigue initiated at high stress concentration points on the gusset plates inserted in the tubular joints. As a consequence of the fractured plates other cracks were nucleated close to the intersection lines of the braces that compose the K-joints. Based on this analysis different repair possibilities were proposed. To comply with the production goals of the Business Unit it was decided to repair the platform on-site and in production in agreement with the Classification Society. The proposed repair contemplated the installation of two flanges on the gusset plates between the diagonal braces by underwater wet (UWW) welding. Cracks at the gusset plates were also removed by grinding and wet welding. Defects located at the braces are being monitored and repaired by the installation of backing bars, by wet welding, followed by grinding and welding from the inside. To carry out the job two weld procedures and ten welder-divers were qualified.


2008 ◽  
Vol 517 (1) ◽  
pp. 31-33 ◽  
Author(s):  
Dong Wang ◽  
Hiroshi Nakashima ◽  
Masanori Tanaka ◽  
Taizoh Sadoh ◽  
Masanobu Miyao ◽  
...  

2006 ◽  
Vol 45 (4B) ◽  
pp. 3007-3011 ◽  
Author(s):  
Atsushi Ogura ◽  
Kosuke Yamasaki ◽  
Daisuke Kosemura ◽  
Satoshi Tanaka ◽  
Ichiro Chiba ◽  
...  

2020 ◽  
Vol 12 (24) ◽  
pp. 10468
Author(s):  
Muhammad Safdar ◽  
Tim Newson ◽  
Colin Schmidt ◽  
Kenichi Sato ◽  
Takuro Fujikawa ◽  
...  

The disposal of 2011 Japan earthquake waste has become an important issue in Japan and it is not realistic or economical to send all of these wastes to landfill sites, due to limited space, high costs, and related environmental issues. In sustainable geotechnical applications, mixing of the separated soils from disaster wastes with additives (e.g., cement and fiber) is required to improve their strength and stiffness characteristics. In this study, monotonic triaxial drained compression tests are performed on medium dense specimens of Toyoura sand-cement-fiber mixtures with different percentages of fiber and cement (e.g., 0–3%) additives. The experimental results indicate that behavior of the mixtures is significantly affected by the concentration of fiber and cement additives. Based on a comprehensive set of test results, modifications to the series of equations were developed that can be used to evaluate the shear modulus and mobilized stress curves at small-strain levels. The experimental results and model comparison show that the elastic threshold strain (γe), reference strain (γr), increases with fiber and cement additives. In addition, the range of curvature parameter, from 0.88 to 1.0, provides a good comparison with the results of small-strain measurements. Overall, the comparison of the results and model shows that the small-strain measurements obtained using local strain transducers fall within the range of model upper and lower bound curves. The results of the unreinforced, fiber, and cemented sand shows a close agreement with the model mean curve, but fiber-reinforced cemented sand shows a good comparison with model upper bound.


2020 ◽  
Author(s):  
Elisabeth Bemer ◽  
Noalwenn Dubos-Sallée ◽  
Patrick N. J. Rasolofosaon

<p>The differences between static and dynamic elastic moduli remain a controversial issue in rock physics. Various empirical correlations can be found in the literature. However, the experimental methods used to derive the static and dynamic elastic moduli differ and may entail substantial part of the discrepancies observed at the laboratory scale. The representativeness and bias of these methods should be fully assessed before applying big data analytics to the numerous datasets available in the literature.</p><p>We will illustrate, discuss and analyze the differences inherent to static and dynamic measurements through a series of triaxial and petroacoustic tests performed on an outcrop carbonate. The studied rock formation is Euville limestone, which is a crinoidal grainstone composed of roughly 99% calcite and coming from Meuse department located in Paris Basin. Sister plugs have been cored from the same quarry block and observed under CT-scanner to check their homogeneity levels.</p><p>The triaxial device is equipped with an internal stress sensor and provides axial strain measurements both from strain gauges glued to the samples and LVDTs placed inside the confinement chamber. Two measures of the static Young's modulus can thus be derived: the first one from the local strain measurements provided by the strain gauges and the second one from the semi-local strain measurements provided by the LVDTs. The P- and S-wave velocities are measured both through first break picking and the phase spectral ratio method, providing also two different measures of the dynamic Young's modulus.</p><p>The triaxial tests have been performed in drained conditions and the measured static elastic moduli correspond to drained elastic moduli. The petroacoustic tests have been performed using the fluid substitution method, which consists in measuring the acoustic velocities for various saturating fluids of different bulk modulus. No weakening or dispersion effects have been observed. Gassmann's equation can then be used to derive the dynamic drained elastic moduli and the solid matrix bulk modulus, which is otherwise either taken from the literature for pure calcite or dolomite samples, or computed using Voigt-Reuss-Hill or Hashin-Shtrikman averaging of the mineral constituents.</p><p>For the studied carbonate formation, we obtain similar values for static and dynamic elastic moduli when derived from careful lab experiments. Based on the obtained results, we will finally make recommendations, emphasizing the necessity of using relevant experimental techniques for a consistent characterization of the relation between static and dynamic elastic moduli.</p>


Sign in / Sign up

Export Citation Format

Share Document