scholarly journals The effect of entrance flow development on vortex formation and wall shear stress in a curved artery model

2021 ◽  
Vol 33 (10) ◽  
pp. 101908
Author(s):  
Christopher Cox ◽  
Michael W. Plesniak
2019 ◽  
Vol 31 (12) ◽  
pp. 121903 ◽  
Author(s):  
Christopher Cox ◽  
Mohammad Reza Najjari ◽  
Michael W. Plesniak

2021 ◽  
pp. 1-12
Author(s):  
Adel M. Malek ◽  
James E. Hippelheuser ◽  
Alexandra Lauric

OBJECTIVE Aneurysm formation preferentially occurs at the site of wide-angle cerebral arterial bifurcations, which were recently shown to have a high longitudinal positive wall shear stress (WSS) gradient that promotes aneurysm formation. The authors sought to explore the other components of the hemodynamic environment that are altered with increasing bifurcation angle in the apical region and the effects of these components on WSS patterns on the vessel wall that may modulate aneurysm genesis and progression. METHODS Parametric models of symmetrical and asymmetrical bifurcations were created with increasing bifurcation angles (45°–240°), and 3D rotational angiography models of 13 middle cerebral artery (MCA) bifurcations (7 aneurysmal, 6 controls) were analyzed using computational fluid dynamics. For aneurysmal bifurcations, the aneurysm was digitally removed to uncover hemodynamics at the apex. WSS vectors along cross-sectional planes distal to the bifurcation apex were decomposed as orthogonal projections to the cut plane into longitudinal and transverse (tangential to the cross-sectional plane) components. Transverse rotational WSS (TRWSS) and TRWSS gradients (TRWSSGs) were sampled and evaluated at the apex and immediately distal from the apex. RESULTS In parametric models, increased bifurcation angle was associated with transverse flow vortex formation with emergence of an associated apical high TRWSS with highly aneurysmogenic positive TRWSSGs. While TRWSS decayed rapidly away from the apex in narrow-angle bifurcations, it remained greatly elevated for many radii downstream in aneurysm-prone wider bifurcations. In asymmetrical bifurcations, TRWSS was higher on the aneurysm-prone daughter vessel associated with the wider angle. Patient-derived models with aneurysmal bifurcations had wider angles (149.33° ± 12.56° vs 98.17° ± 8.67°, p < 0.001), with significantly higher maximum TRWSS (1.37 ± 0.67 vs 0.48 ± 0.23 Pa, p = 0.01) and TRWSSG (1.78 ± 0.92 vs 0.76 ± 0.50 Pa/mm, p = 0.03) compared to control nonaneurysmal bifurcations. CONCLUSIONS Wider vascular bifurcations are associated with a novel and to the authors’ knowledge previously undescribed transverse component rotational wall shear stress associated with a positive (aneurysmogenic) spatial gradient. The resulting hemodynamic insult, demonstrated in both parametric models and patient-based anatomy, is noted to decay rapidly away from the protection of the medial pad in healthy narrow-angle bifurcations but remain elevated distally downstream of wide-angle aneurysm-prone bifurcations. This TRWSS serves as a new contribution to the hemodynamic environment favoring aneurysm formation and progression at wide cerebral bifurcations and may have clinical implications favoring interventions that reduce bifurcation angle.


Author(s):  
Brett Freidkes ◽  
David A. Mills ◽  
Casey Keane ◽  
Lawrence S. Ukeiley ◽  
Mark Sheplak

2020 ◽  
Vol 59 (SK) ◽  
pp. SKKE16 ◽  
Author(s):  
Ryo Nagaoka ◽  
Kazuma Ishikawa ◽  
Michiya Mozumi ◽  
Magnus Cinthio ◽  
Hideyuki Hasegawa

Water ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1587
Author(s):  
Dolat Khan ◽  
Ata ur Rahman ◽  
Gohar Ali ◽  
Poom Kumam ◽  
Attapol Kaewkhao ◽  
...  

Due to the importance of wall shear stress effect and dust fluid in daily life fluid problems. This paper aims to discover the influence of wall shear stress on dust fluids of fluctuating flow. The flow is considered between two parallel plates that are non-conducting. Due to the transformation of heat, the fluid flow is generated. We consider every dust particle having spherical uniformly disperse in the base fluid. The perturb solution is obtained by applying the Poincare-Lighthill perturbation technique (PLPT). The fluid velocity and shear stress are discussed for the different parameters like Grashof number, magnetic parameter, radiation parameter, and dusty fluid parameter. Graphical results for fluid and dust particles are plotted through Mathcad-15. The behavior of base fluid and dusty fluid is matching for different embedded parameters.


Sign in / Sign up

Export Citation Format

Share Document