THE ORIGIN AND INFLUENCE OF OVERPRESSURE WITH REFERENCE TO THE NORTH WEST SHELF, AUSTRALIA

1999 ◽  
Vol 39 (1) ◽  
pp. 64 ◽  
Author(s):  
R.E. Swarbrick ◽  
R.R. Hillis
Keyword(s):  
Source Rocks ◽  
Lateral Strain ◽  
Hydrocarbon Generation ◽  
Large Magnitude ◽  
Gas Generation ◽  
North West ◽  
Fine Grained ◽  
Seal Integrity ◽  
The North ◽  
High Magnitude

The dominant cause of overpressure in basins is rapid loading of fine-grained sediments in which incomplete dewatering leads to additional overburden load being supported partly by the pore fluids. The principal controls on the magnitude of overpressure created are permeability and compressibility of the fine-grained rocks, coupled with the loading or sedimentation rate. High magnitude overpressure requires rapid sedimentation and/or evolution of sediment permeability to nanoDarcy values at shallow depth. By contrast, most fluid expansion mechanisms can be shown to be ineffective at generating large magnitude overpressure at realistic basin conditions. Only gas generation (either directly from kerogen or by oil to gas cracking) has the potential to create large magnitude overpressure, and only if the connected reservoir volume is very restricted.The origin of overpressure in the North West Shelf, especially the Northern Carnarvon Basin has previously been suggested to be due to petroleum generation, principally because the top of overpressure is coincident with, or lies below, the hydrocarbon generation window. To achieve high magnitude overpressure by this mechanism requires large volumes of gas generative source rocks connected to reservoirs of extremely limited extent. The volume of reservoir rocks in the basins is relatively high, and gas generation appears to be only a secondary mechanism. The most likely origin of overpressure is burial of the Jurassic and Lower Cretaceous group sediments (including the Muderong Shale) with early development of the Muderong Shale as a pressure seal. Lateral stress cannot be discounted as an additional mechanism of overpressure generation. However, lateral strain appears to be significantly less than vertical strain.Overpressure has the potential to influence the petroleum system in the North West Shelf if there has been high magnitude overpressure for prolonged periods of geological time. Normally pressured units today may have had a history of overpressure in the geological past. Reservoir quality can be enhanced by overpressure, but trap seal integrity either strengthened or weakened by overpressure. Timing of maturation and migration of hydrocarbon can also be affected.

THE EFFECT OF INERTINITE ON KEROGEN APPRAISAL BY PROGRAMMED PYROLYSIS, NORTH WEST SHELF, AUSTRALIA

1994 ◽  
Vol 34 (1) ◽  
pp. 297
Author(s):  
E.L. Horstman
Keyword(s):  
Organic Carbon ◽  
Oil And Gas ◽  
Hydrogen Index ◽  
Source Rocks ◽  
Gas Generation ◽  
North West ◽  
The North ◽  
Measured Amount

The oil potential of rocks containing inertinite is systematically underestimated by chemical or programmed pyrolysis techniques. Inertinite is measured as organic carbon, but does not contribute to the hydrocarbons produced during pyrolysis. When maceral data is available the measured amount of organic carbon can be recalculated to establish an Hydrogen Index based only on the kerogen which might contribute to oil and gas generation. Inertiniterich rocks that were previously discounted as being only gas prone should be reviewed.Recalculated HI:OI plots prepared from samples from the North West Shelf of Australia indicate the presence of significant amounts of oil-prone kerogen in source rocks previously evaluated as being predominantly gas-prone, upgrading the oil potential of the area.

scholarly journals Reconstruction of burial history, temperature, source rock maturity and hydrocarbon generation in the northwestern Dutch offshore

2012 ◽  
Vol 91 (4) ◽  
pp. 535-554 ◽  
Author(s):  
R. Abdul Fattah ◽  
J.M. Verweij ◽  
N. Witmans ◽  
J.H. ten Veen
Keyword(s):  
Source Rock ◽  
Source Rocks ◽  
Northwestern Part ◽  
Hydrocarbon Generation ◽  
Burial History ◽  
Coal Seams ◽  
Gas Generation ◽  
Offshore Area ◽  
The North ◽  
Late Generation

Abstract3D basin modelling is used to investigate the history of maturation and hydrocarbon generation on the main platforms in the northwestern part of the offshore area of the Netherlands. The study area covers the Cleaverbank and Elbow Spit Platforms. Recently compiled maps and data are used to build the input geological model. An updated and refined palaeo water depth curve and newly refined sediment water interface temperatures (SWIT) are used in the simulation. Basal heat flow is calculated using tectonic models. Two main source rock intervals are defined in the model, Westphalian coal seams and pre-Westphalian shales, which include Namurian and Dinantian successions. The modelling shows that the pre-Westphalian source rocks entered the hydrocarbon generation window in the Late Carboniferous. In the southern and central parts of the study area, the Namurian started producing gas in the Permian. In the north, the Dinantian source rocks appear to be immature. Lower Westphalian sediments started generating gas during the Upper Triassic. Gas generation from Westphalian coal seams increased during the Paleogene and continues in present-day. This late generation of gas from Westphalian coal seams is a likely source for gas accumulations in the area.Westphalian coals might have produced early nitrogen prior to or during the main gas generation occurrence in the Paleogene. Namurian shales may be a source of late nitrogen after reaching maximum gas generating phase in the Triassic. Temperatures reached during the Mid Jurassic were sufficiently high to allow the release of non-organic nitrogen from Namurian shales.

scholarly journals Fine evaluation and favorable area prediction of deep source rocks in northern Songliao Basin

2021 ◽  
Vol 329 ◽  
pp. 01056
Author(s):  
Fan Zhang ◽  
Yanjie Li ◽  
Xiaoshan Ji ◽  
Qiuli Huo ◽  
Yuming Wu ◽  
...  
Keyword(s):  
Natural Gas ◽  
Comprehensive Evaluation ◽  
Thermal Evolution ◽  
Songliao Basin ◽  
Source Rocks ◽  
Hydrocarbon Generation ◽  
Gas Generation ◽  
The North ◽  
Geological Conditions ◽  
Exploration Area

Focusing on Xujiaweizi fault depression, the geological conditions and geochemical characteristics of deep natural gas formation in the north of Songliao basin are evaluated, the natural gas resources are estimated, and the favorable areas are optimized. Shahezi Formation shale is a set of coal bearing sediments with high organic matter abundance (TOC is 1%～12%), high over maturity (Ro is 1%～4%) and shore shallow lake facies, which are mainly distributed in Xujiaweizi fault depression, Gulong-Lindian fault depression and Yingshan fault depression. The thickness, TOC, Ro and hydrocarbon generation of four thirdorder sequences with different lithology (mudstone and coal) are carefully evaluated for the Shahezi Formation shale in the deep layer of Songbei. The comprehensive evaluation shows that the mudstone thickness of Es4 member in Anda and Xuzhong areas of Xujiaweizi fault depression is large (150 ~ 525m), TOC is high (1% ~ 4%), thermal evolution degree is high (Ro is 1.2% ~ 3.4%), and gas generation intensity is high (20 ~ 815) × 108m3 / t), moderate buried depth (3000~4500m) and overlapping area of 756km2. It is a favorable exploration area for natural gas and shale gas in Daqing Oilfield.

Depositional Environment Drive as Overpressure Generation: Study Case in “Gap” Field, North West Java Basin

2020 ◽  
Author(s):  
A., C. Prasetyo
Keyword(s):  
Clay Mineral ◽  
Depositional Environment ◽  
Mineral Content ◽  
Hydrocarbon Generation ◽  
Well Test ◽  
Burial History ◽  
The South ◽  
North West ◽  
The North ◽  
Geological Processes

Overpressure existence represents a geological hazard; therefore, an accurate pore pressure prediction is critical for well planning and drilling procedures, etc. Overpressure is a geological phenomenon usually generated by two mechanisms, loading (disequilibrium compaction) and unloading mechanisms (diagenesis and hydrocarbon generation) and they are all geological processes. This research was conducted based on analytical and descriptive methods integrated with well data including wireline log, laboratory test and well test data. This research was conducted based on quantitative estimate of pore pressures using the Eaton Method. The stages are determining shale intervals with GR logs, calculating vertical stress/overburden stress values, determining normal compaction trends, making cross plots of sonic logs against density logs, calculating geothermal gradients, analyzing hydrocarbon maturity, and calculating sedimentation rates with burial history. The research conducted an analysis method on the distribution of clay mineral composition to determine depositional environment and its relationship to overpressure. The wells include GAP-01, GAP-02, GAP-03, and GAP-04 which has an overpressure zone range at depth 8501-10988 ft. The pressure value within the 4 wells has a range between 4358-7451 Psi. Overpressure mechanism in the GAP field is caused by non-loading mechanism (clay mineral diagenesis and hydrocarbon maturation). Overpressure distribution is controlled by its stratigraphy. Therefore, it is possible overpressure is spread quite broadly, especially in the low morphology of the “GAP” Field. This relates to the delta depositional environment with thick shale. Based on clay minerals distribution, the northern part (GAP 02 & 03) has more clay mineral content compared to the south and this can be interpreted increasingly towards sea (low energy regime) and facies turned into pro-delta. Overpressure might be found shallower in the north than the south due to higher clay mineral content present to the north.

scholarly journals I.—Microscopic Structure of Irish Granites. No. 2. Granite of Aillemore, Co. Mayo

1874 ◽  
Vol 1 (1) ◽  
pp. 1-2
Author(s):  
Edward Hull
Keyword(s):  
The Other ◽  
Microscopic Structure ◽  
South Side ◽  
North West ◽  
Fine Grained ◽  
Lower Silurian ◽  
The North ◽  
Geological Map ◽  
Vertical Walls ◽  
Dark Green

This granite forms an isolated mass, rising into two eminences a few miles south of Louisburg, called Corvock Brack (1287 feet) and Knockaskeheen (1288 feet). It is a greyish granite—generally fine—grained—consisting of quartz, two felspars,—one orthoclase, the other triclinic, probably oligoclase—and dark green mica. In some places there are patches in which the felspar assumes the appearance of “graphic granite.” Numerous boulders of this granite are strewn over the district to the north-west, and on the south side of Knockaskeheen; the rock is traversed by regular joints ranging N. 10 W., along which it splits off into nearly vertical walls. The position of the granite is shown on Griffith's Geological Map of Ireland, and it is surrounded by schistose beds, generally metamorphosed, and probably of Lower Silurian age. The granite itself is of older date than the Upper Llandovery beds, which lie to the southward.

scholarly journals The characteristics of hydrocarbon generation, reserving performances of fine-grained rock, and preservation conditions of coal measure shale gas of an epicontinental sea basin: A case study of the Late Palaeozoic shale gas in the Huanghebei Area of Western Shandong

2018 ◽  
Vol 37 (1) ◽  
pp. 453-472 ◽  
Author(s):  
Ying Li ◽  
Zengxue Li ◽  
Huaihong Wang ◽  
Dongdong Wang
Keyword(s):  
Coal Seam ◽  
Shale Gas ◽  
Late Paleozoic ◽  
Organic Carbon Content ◽  
Hydrocarbon Generation ◽  
Average Content ◽  
Gas Generation ◽  
Geological Structures ◽  
Fine Grained ◽  
Western Shandong

In China, marine and land transitional fine-grained rocks (shale, mudstone, and so on) are widely distributed and are known to have large accumulated thicknesses. However, shale gas explorations of these types of rock have only recently been initiated, thus the research degree is very low. Therefore, this study was conducted in order to improve the research data regarding the gas accumulation theory of marine and continental transitional fine-grained rock, as well as investigate the shale gas generation potential in the Late Paleozoic fine-grained rock masses located in the Huanghebei Area of western Shandong Province. The hydrocarbon generation characteristics of the epicontinental sea coal measures were examined using sedimentology, petrography, geochemistry, oil and gas geology, tectonics, and combined experimental testing processes. The thick fine-grained rocks were found to have been deposited in the sedimentary environments of the tidal flats, barriers, lagoons, deltas, and rivers during the Late Paleozoic in the study area. The most typical fine-grained rocks were located between the No. 5 coal seam of the Shanxi Formation and the No. 10 coal seam of the Taiyuan Formation, with an average thickness of 84.8 m. These formations were mainly distributed in the western section of the Huanghebei Area. The total organic carbon content level of the fine-grained rock was determined to be 2.09% on average, and the higher content levels were located in the western section of the Huanghebei Area. The main organic matter types of the fine-grained rock were observed to be kerogen II, followed by kerogen III. The vitrinite reflectance ( Ro) of the fine-grained rock was between 0.72 and 1.25%, which indicated that the gas generation of the dark fine-grained rock was within a favorable range, and the maturity of the rock was mainly in a medium stage in the northern section of the Huanghebei Area. It was determined that the average content of brittle minerals in the fine-grained rock was 55.7%. The dissolution pores and micro-cracks were the dominating pores in the fine-grained rock, followed by intergranular pores and intercrystalline pores. It was also found that both the porosity and permeability of the fine-grained rock were very low in the study area. The desorption gas content of the fine-grained rock was determined to be between 0.986 and 4.328 m3/t, with an average content of 2.66 m3/t. The geological structures were observed to be simple in the western section of the Huanghebei Area, and the occurrence impacts on the shale gas were minimal. However, the geological structures were found be complex in the eastern section of the study area, which was unfavorable for shale gas storage. The depths of the fine-grained rock were between 414.05 and 1290.55 m and were observed to become increasingly deeper from the southwestern section to the northern section. Generally speaking, there were found to be good reservoir forming conditions and great resource potential for marine and continental transitional shale gas in the study area.

scholarly journals Evaluation of hydrocarbons generated from the Permo-Carboniferous source rocks in Huanghua Depression of the Bohai Bay Basin, China

2018 ◽  
Vol 36 (5) ◽  
pp. 1229-1244
Author(s):  
Xiao-Rong Qu ◽  
Yan-Ming Zhu ◽  
Wu Li ◽  
Xin Tang ◽  
Han Zhang
Keyword(s):  
Oil And Gas ◽  
Source Rocks ◽  
Bohai Bay ◽  
Hydrocarbon Generation ◽  
Burial History ◽  
Bohai Bay Basin ◽  
Important Conclusion ◽  
The North ◽  
Huanghua Depression ◽  
History Of

The Huanghua Depression is located in the north-centre of Bohai Bay Basin, which is a rift basin developed in the Mesozoic over the basement of the Huabei Platform, China. Permo-Carboniferous source rocks were formed in the Huanghua Depression, which has experienced multiple complicated tectonic alterations with inhomogeneous uplift, deformation, buried depth and magma effect. As a result, the hydrocarbon generation evolution of Permo-Carboniferous source rocks was characterized by discontinuity and grading. On the basis of a detailed study on tectonic-burial history, the paper worked on the burial history, heating history and hydrocarbon generation history of Permo-Carboniferous source rocks in the Huanghua Depression combined with apatite fission track testing and fluid inclusion analyses using the EASY% Ro numerical simulation. The results revealed that their maturity evolved in stages with multiple hydrocarbon generations. In this paper, we clarified the tectonic episode, the strength of hydrocarbon generation and the time–spatial distribution of hydrocarbon regeneration. Finally, an important conclusion was made that the hydrocarbon regeneration of Permo-Carboniferous source rocks occurred in the Late Cenozoic and the subordinate depressions were brought forward as advantage zones for the depth exploration of Permo-Carboniferous oil and gas in the middle-northern part of the Huanghua Depression, Bohai Bay Basin, China.

ACCURATE RECOGNITION OF SOURCE ROCK CHARACTER IN THE JURASSIC OF THE NORTH WEST SHELF, WESTERN AUSTRALIA

1992 ◽  
Vol 32 (1) ◽  
pp. 289 ◽  
Author(s):  
John Scott
Keyword(s):  
Source Rock ◽  
Organic Material ◽  
Source Rocks ◽  
Higher Plant ◽  
Pyrolysis Gas ◽  
Screening Analysis ◽  
North West ◽  
The North ◽  
Potential Source Rock ◽  
Rock Eval

The main potential source rock intervals are generally well defined on the North West Shelf by screening analysis such as Rock-Eval. The type of product from the source rocks is not well defined, owing to inadequacies in current screening analysis techniques. The implications of poor definition of source type in acreage assessment are obvious. The type of product is dependent on the level of organic maturity of the source rock, the ability of products to migrate out of the source rock and on the type of organic material present. The type of kerogen present is frequently determined by Rock-Eval pyrolysis. However, Rock-Eval has severe limitations in defining product type when there is a significant input of terrestrial organic material. This problem has been recognised in Australian terrestrial/continental sequences but also occurs where marine source rock facies contain terrestrially-derived higher plant material. Pyrolysis-gas chromatography as applied to source rock analysis provides, by molecular typing, a better method of estimating the type of products of the kerogen breakdown than bulk chemical analysis such as Rock-Eval pyrolysis.

Observations on the Lower Triassic petroleum prospectivity of the offshore Carnarvon and Roebuck basins

2016 ◽  
Vol 56 (1) ◽  
pp. 173 ◽  
Author(s):  
Stephen Molyneux ◽  
Jeff Goodall ◽  
Roisin McGee ◽  
George Mills ◽  
Birgitta Hartung-Kagi
Keyword(s):  
Regional Analysis ◽  
Lower Triassic ◽  
Source Rocks ◽  
Upper Permian ◽  
Regional Study ◽  
North West ◽  
Petroleum Systems ◽  
The North ◽  
Depositional Processes ◽  
Water Margin

Why are the only commercial hydrocarbon discoveries in Lower Triassic and Permian sediments of the western margin of Australia restricted to the Perth Basin and the Petrel Sub-basin? Recent regional analysis by Carnarvon Petroleum has sought to address some key questions about the Lower Triassic Locker Shale and Upper Permian Chinty and Kennedy formations petroleum systems along the shallow water margin of the Carnarvon and offshore Canning (Roebuck/Bedout) basins. This paper aims to address the following questions:Source: Is there evidence in the wells drilled to date of a working petroleum system tied to the Locker Shale or other pre-Jurassic source rocks? Reservoir: What is the palaeogeography and sedimentology of the stratigraphic units and what are the implications for the petroleum systems?The authors believed that a fresh look at the Lower Triassic to Upper Permian petroleum prospectivity of the North West Shelf would be beneficial, and key observations arising from the regional study undertaken are highlighted:Few wells along a 2,000 km area have drilled into Lower Triassic Locker Shale or older stratigraphy. Several of these wells have been geochemically and isotopically typed to potentially non Jurassic source rocks. The basal Triassic Hovea Member of the Kockatea Shale in the Perth Basin is a proven commercial oil source rock and a Hovea Member Equivalent has been identified through palynology and a distinctive sapropelic/algal kerogen facies in nearly 16 wells that penetrate the full Lower Triassic interval on the North West Shelf. Samples from the Upper Permian, the Hovea Member Equivalent and the Locker Shale have been analysed isotopically indicating –28, –34 and –30 delta C13 averages, respectively. Lower Triassic and Upper Permian reservoirs are often high net to gross sands with up to 1,000 mD permeability and around 20% porosity. Depositional processes are varied, from Locker Shale submarine canyon systems to a mixed carbonate clastic marine coastline/shelf of the Upper Permian Chinty and Kennedy formations.

Sign in / Sign up

Export Citation Format

Share Document