A NUMERICAL STUDY OF THE FLOW OF GRANULAR MATERIALS BETWEEN TWO VERTICAL FLAT PLATES WHICH ARE AT DIFFERENT TEMPERATURES

1999 ◽  
Vol 17 (1-2) ◽  
pp. 149-163 ◽  
Author(s):  
TRAN X. PHUOC ◽  
MEHRDAD MASSOUDI
Keyword(s):  
Granular Materials ◽  
Numerical Study ◽  
Flat Plates ◽  
Different Temperatures

On the Motion of Granular Materials Due to Shear

2000 ◽  
Author(s):  
Mehrdad Massoudi ◽  
Tran X. Phuoc
Keyword(s):  
Finite Difference ◽  
Granular Materials ◽  
Continuum Model ◽  
Theory Model ◽  
Governing Equations ◽  
Flat Plates ◽  
Material Parameters ◽  
Finite Difference Technique ◽  
Linear Differential ◽  
The Continuum

Abstract In this paper we study the flow of granular materials between two horisontal flat plates where the top plate is moving with a constant speed. The constitutive relation used for the stress is based on the continuum model proposed by Rajagopal and Massoudi (1990), where the material parameters are derived using the kinetic theory model proposed by Boyle and Massoudi (1990). The governing equations are non-dimensionalized and the resulting system of non-linear differential equations is solved numerically using finite difference technique.

Numerical study of asymmetric and axisymmetric thermal jet with entropy generation concept

2021 ◽  
Vol 15 (1) ◽  
pp. 7628-7636
Author(s):  
D. Belakhal ◽  
Kouider Rahmani ◽  
Amel Elkaroui Elkaroui ◽  
Syrine Ben Haj Ayech ◽  
Nejla Mahjoub Saïd ◽  
...  
Keyword(s):  
Entropy Generation ◽  
Numerical Study ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Variable Density ◽  
Current Investigation ◽  
Numerical Resolution ◽  
Different Temperatures ◽  
Density Ratios ◽  
The Impact

In the current investigation, numerical study of a thermal jet of asymmetric (rectangular and elliptical) and axisymmetric (circular) geometry was investigated with variable density to verify the impact of the ratio of density and geometry on the generation of entropy. The central jet was brought to different temperatures (194, 293 and 2110 K) to obtain density ratios (0.66, 1 and 7.2) identical to a mixture jet ((Air-CO2), (Air-Air) and (Air-He)), respectively. Solving the three-dimensional numerical resolution of the Navier Stocks for turbulent flow permanent enclosed on the turbulence model K-εstandard was made. The results acquired are compared with that carried out in previous experimental studies, where it was concluded that, the axisymmetric (circular) geometry increases the entropy generation.

Effective Thermal Conductivity of Submicron Powders: A Numerical Study

2016 ◽  
Vol 846 ◽  
pp. 500-505
Author(s):  
Wei Jing Dai ◽  
Yi Xiang Gan ◽  
Dorian Hanaor
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Effective Thermal Conductivity ◽  
Granular Materials ◽  
Gas Phase ◽  
Numerical Study ◽  
Transfer Model ◽  
Size Of Particles ◽  
Contact Unit

Effective thermal conductivity is an important property of granular materials in engineering applications and industrial processes, including the blending and mixing of powders, sintering of ceramics and refractory metals, and electrochemical interactions in fuel cells and Li-ion batteries. The thermo-mechanical properties of granular materials with macroscopic particle sizes (above 1 mm) have been investigated experimentally and theoretically, but knowledge remains limited for materials consisting of micro/nanosized grains. In this work we study the effective thermal conductivity of micro/nanopowders under varying conditions of mechanical stress and gas pressure via the discrete thermal resistance method. In this proposed method, a unit cell of contact structure is regarded as one thermal resistor. Thermal transport between two contacting particles and through the gas phase (including conduction in the gas phase and heat transfer of solid-gas interfaces) are the main mechanisms. Due to the small size of particles, the gas phase is limited to a small volume and a simplified gas heat transfer model is applied considering the Knudsen number. During loading, changes in the gas volume and the contact area between particles are simulated by the finite element method. The thermal resistance of one contact unit is calculated through the combination of the heat transfer mechanisms. A simplified relationship between effective thermal conductivity and loading pressure can be obtained by integrating the contact units of the compacted powders.

A comprehensive numerical study of jet flow impingement over flat plates at varied angles

2001 ◽  
Author(s):  
Junxiao Wu ◽  
Lin Tang ◽  
Edward Luke ◽  
Xiao-Ling Tong ◽  
Pasquale Cinella
Keyword(s):  
Numerical Study ◽  
Jet Flow ◽  
Flat Plates

Comprehensive Numerical Study of Jet-Flow Impingement over Flat Plates

2002 ◽  
Vol 39 (3) ◽  
pp. 357-366 ◽  
Author(s):  
Junxiao Wu ◽  
Lin Tang ◽  
Edward A. Luke ◽  
Xiao-Ling Tong ◽  
Pasquale Cinnella
Keyword(s):  
Numerical Study ◽  
Jet Flow ◽  
Flat Plates

scholarly journals Numerical study of one-dimensional compression in granular materials

2015 ◽  
Vol 5 (July–September) ◽  
pp. 96-103
Author(s):  
◽  
C. O'Sullivan ◽  
◽  
◽  
Keyword(s):  
Granular Materials ◽  
Numerical Study ◽  
One Dimensional

Three Dimensional Numerical Modelling of Staggered Tube Bundle Turbulent Crossflow in Duct

2005 ◽  
Author(s):  
Ahad Ramezanpour ◽  
Hassan Shirvani ◽  
Ramin Rahmani ◽  
Iraj Mirzaee
Keyword(s):  
Nusselt Number ◽  
Numerical Study ◽  
Tube Bundle ◽  
Three Dimensional ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Wall Function ◽  
Flat Plates ◽  
Geometrical Characteristics ◽  
Commercial Code

A numerical study has been conducted to investigate the three dimensional (3D) staggered tube bundle turbulent cross flow confined between two parallel flat plates using RNG k-ε model and standard wall function utilizing commercial code FLUENT. The maximum Reynolds numbers of 1000, 5000, and 50000 and the distance between plates of H = 3, 5, 10, 15, and 20 mm have been considered. The arrangement of the staggered tube bundle is fix with geometrical characteristics of Sn/D = 1.5 and Sp/D = 1.2 which has been found optimum in previous two-dimensional studies. The constant temperature of 360K on tubes, constant inlet flow and plates’ temperature of 300K have been set as the boundary conditions. The global Nusselt number, friction factor for the dissimilar Reynolds numbers, distance between plates, local Nusselt number and different angles on first and third tubes have been evaluated.

Sign in / Sign up

Export Citation Format

Share Document