Optimization of spray drying operating conditions for production of functional milk powder encapsulating bee pollen

2020 ◽  
pp. 1-14 ◽  
Author(s):  
Mamta Thakur ◽  
Kirty Pant ◽  
Rishi Ravindra Naik ◽  
Vikas Nanda
Author(s):  
Timothy A. G. Langrish ◽  
Xing Huang ◽  
Chao Zhong

Wall deposition tests have been conducted on a new spray-drying sytem. Solutions of salt and skim milk powder have been dried with different inlet temperatures (170 °C and 230 °C) and solid contents (8.8 wt% and 30 wt%). The experiment showed that increasing the temperature caused an decrease in the amount of deposition for salt solution, but an increase for skim milk. The experiments also showed that a higher solid content caused an increase in deposition. The trends agreed with the studies using a conventional spray dryer, but the amount of deposition appeared to be lower in the new spray dryer at the same operating conditions Keywords: Spray drying; wall deposition


2021 ◽  
Vol 383 ◽  
pp. 302-317
Author(s):  
M. Gabriela Bordón ◽  
Noelia P.X. Alasino ◽  
Vanina Martínez ◽  
Regina Gauna Peter ◽  
Ramiro Iturralde ◽  
...  

1955 ◽  
Vol 53 (4) ◽  
pp. 387-397 ◽  
Author(s):  
P. H. R. Anderson ◽  
Doris M. Stone

SummaryEight explosive outbreaks of food poisoning, occurring in school canteens in England during 1953 and affecting 1190 known cases, are described. The clinical features were characteristic of the toxin type of illness. No deaths occurred.The food causing all of these outbreaks was prepared from spray-dried skim milk powder. It was not subsequently heat-treated and was usually consumed 3–4 hr. after preparation.The spray-dried milk powder proved to contain a high content of bacteria, including large numbers of Staph. aureus, of a phage pattern often associated with food poisoning. The assumption was therefore made that these outbreaks were caused by staphylococcal enterotoxin.Because the food was often consumed within 3–4 hr. of reconstitution of the milk powder—before, in fact, the staphylococci had had time to grow—it is concluded that the poisoning must have been due mainly to pre-formed toxin.Consideration is given to the opportunities for the formation of toxin in a spray-drying plant, and reasons are brought forward for believing that it is formed mainly in the balance tank where the warm milk is kept, sometimes for several hours, before passing into the final drying chamber.The processing of the milk and the precautions for preventing contamination of the finished product are discussed.


2021 ◽  
Author(s):  
K. Cevik ◽  
H. Yalcin

Abstract The aim of this study was to investigate microencapsulation of palm oil fractions (palm olein (POL) and 90% palm olein+10% palm stearin (POS)) using skim milk powder (SMP) and maltodextrin (MD) by spray drying. Twenty-seven emulsions with POL were prepared to determine appropriate solid content (SC) and oil/coating material ratio (O/CM) of the emulsions to be fed into the spray dryer. Emulsion properties, such as viscosity and stability, were affected by SC and coating materials. The effects of coating materials used in microencapsulation of POL and POS were also tested by using different ratios of SMP and MD. The microencapsulation efficiency (69.28–84.97%), the microencapsulation yield (14.50–31.79%), and the peroxide value (4.12–7.07 meq O2/kg oil) of the powders were affected by the coating materials (P < 0.05).


2018 ◽  
Vol 83 (12) ◽  
pp. 2983-2991 ◽  
Author(s):  
Haileeyesus Habtegebriel ◽  
Michael Wawire ◽  
Daniel Sila

1991 ◽  
Vol 17 (1) ◽  
pp. 216-220
Author(s):  
Shun-ichi Kudoh ◽  
Jiro Koga ◽  
Shiro Matsumoto ◽  
Ichiro Inoue

Foods ◽  
2020 ◽  
Vol 9 (9) ◽  
pp. 1177
Author(s):  
Zalizawati Abdullah ◽  
Farah Saleena Taip ◽  
Siti Mazlina Mustapa Kamal ◽  
Ribhan Zafira Abdul Rahman

The moisture content of a powder is a parameter crucial to be controlled in order to produce stable products with a long shelf life. Inferential control is the best solution to control the moisture content due to difficulty in measuring this variable online. In this study, fundamental and empirical approaches were used in designing the nonlinear model-based inferential control of moisture content of coconut milk powder that was produced from co-current spray dryer. A one-dimensional model with integration of reaction engineering approach (REA) model was used to represent the dynamic of the spray drying process. The empirical approach, i.e., nonlinear autoregressive with exogenous input (NARX) and neural network, was used to allow fast and accurate prediction of output response in inferential control. Minimal offset (<0.0003 kg/kg) of the responses at various set points indicate high accuracy of the neural network estimator. The nonlinear model-based inferential control was able to provide stable control response at wider process operating conditions and acceptable disturbance rejection. Nevertheless, the performance of the controller depends on the tuning rules used.


Sign in / Sign up

Export Citation Format

Share Document