Strategic integration of single flash geothermal steam cycle (SFGSC) and ejector assisted dual-evaporator organic flash refrigeration cycle (EADEOFRC) for power and multi-temperature cooling: 2nd law performance study

2021 ◽  
pp. 1-13
Author(s):  
Subha Mondal ◽  
Chitta Sahana ◽  
Sudipta De
Keyword(s):  
Refrigeration Cycle ◽  
Performance Study ◽  
Strategic Integration ◽  
Single Flash ◽  
Steam Cycle

A Comparative Performance Study of an Ejector-Expansion Refrigeration Cycle Using R134a and its Alternatives: Application of Automobile Air Conditioning

2021 ◽  
Author(s):  
Kadhim K. Idan Al-Chlaihawi ◽  
Hakim T. Kadhim ◽  
Ahmad Hashim Yousif
Keyword(s):  
Air Conditioning ◽  
Cooling Capacity ◽  
Exergy Efficiency ◽  
Refrigeration Cycle ◽  
Performance Study ◽  
Alternative Refrigerants ◽  
Suitable Alternative ◽  
Discharge Temperature ◽  
Volumetric Cooling ◽  
Automobile Air Conditioning

In this study, the performance of ejector-expansion refrigeration cycle (EERC) with R134a alternative refrigerants (R152a, R1234yf, R404A, R407C, R507A and R600a) for automobile air-conditioning application is investigated numerically. The ejector is modeled with a constant mixing-pressure assumption taking into consideration the friction effect in the ejector mixing section. The studied refrigerants are compared based on the optimum area ratio, discharge temperature, compressor input power, volumetric cooling capacity, exergy destruction, COP, exergy efficiency and COP improvement. The results show that R152a and R1234yf have the closest performance to R134a and can be considered the most suitable alternative refrigerants for R134a. The COP and exergy efficiency are improved by 2.26% and 2.27%, respectively, using R152a compared to the use of R134a, whereas they are reduced by 2.89% and 2.88% using R1234yf. The volumetric cooling capacity is reduced for both R152a and R1234yf by 6.14% and 6.8%, respectively. In addition, the effect of compressor rotational speed on the performances is reported.

Replication of the Superstition and Performance Study by

2014 ◽  
Vol 45 (3) ◽  
pp. 239-245 ◽  
Author(s):  
Robert J. Calin-Jageman ◽  
Tracy L. Caldwell
Keyword(s):  
Task Difficulty ◽  
Statistical Power ◽  
Meta Analysis ◽  
A Priori ◽  
Significant Heterogeneity ◽  
Performance Study ◽  
Improve Performance ◽  
Research Designs ◽  
Series Of Experiments ◽  
And Performance

A recent series of experiments suggests that fostering superstitions can substantially improve performance on a variety of motor and cognitive tasks ( Damisch, Stoberock, & Mussweiler, 2010 ). We conducted two high-powered and precise replications of one of these experiments, examining if telling participants they had a lucky golf ball could improve their performance on a 10-shot golf task relative to controls. We found that the effect of superstition on performance is elusive: Participants told they had a lucky ball performed almost identically to controls. Our failure to replicate the target study was not due to lack of impact, lack of statistical power, differences in task difficulty, nor differences in participant belief in luck. A meta-analysis indicates significant heterogeneity in the effect of superstition on performance. This could be due to an unknown moderator, but no effect was observed among the studies with the strongest research designs (e.g., high power, a priori sampling plan).

Performance study of RTV-2 Silicone Rubber Material For Soft Actuator by Experimental and Numerical methods: The Effect of Inflation Pressure and Wall Thickness

2020 ◽  
Vol 17 (1) ◽  
pp. 7524-7532 ◽  
Author(s):  
Deepak D. ◽  
Nitesh Kumar ◽  
Shreyas P. Shetty ◽  
Saurabh Jain ◽  
Manoj Bhat
Keyword(s):  
Numerical Methods ◽  
Wall Thickness ◽  
Silicone Rubber ◽  
Inflation Pressure ◽  
Performance Study ◽  
Rubber Material ◽  
Soft Actuator ◽  
Alternative Materials ◽  
Load Carrying ◽  
Influential Parameters

The expensive nature of currently used materials in the soft robotic industry demands the consideration of alternative materials for fabrication. This work investigates the performance of RTV-2 grade silicone rubber for fabrication of a soft actuator. Initially, a cylindrical actuator is fabricated using this material and its performance is experimentally assessed for different pressures. Further, parametric variations of the effect of wall thickness and inflation pressure are studied by numerical methods. Results show that, both wall thickness and inflation pressure are influential parameters which affect the elongation behaviour of the actuator. Thin (1.5 mm) sectioned actuators produced 76.97% more elongation compared to thick sectioned, but the stress induced is 89.61 % higher. Whereas, the thick sectioned actuator (6 mm) showed a higher load transmitting capability. With change in wall thickness from 1.5 mm to 6 mm, the elongation is reduced by 76.97 %, 38.35 %, 21.05 % and 11.43 % at pressure 100 kPa, 75 kPa, 50 kPa and 25 kPa respectively. The induced stress is also found reduced by 89.61 %, 86.66 %, 84.46 % and 68.68 % at these pressures. The average load carrying capacity of the actuator is found to be directly proportional to its wall thickness and inflation pressure.

Sign in / Sign up

Export Citation Format

Share Document